| if ARCH_OMAP |
| |
| menu "TI OMAP Implementations" |
| |
| config ARCH_OMAP_OTG |
| bool |
| |
| choice |
| prompt "OMAP System Type" |
| default ARCH_OMAP2PLUS |
| |
| config ARCH_OMAP1 |
| bool "TI OMAP1" |
| select COMMON_CLKDEV |
| help |
| "Systems based on omap7xx, omap15xx or omap16xx" |
| |
| config ARCH_OMAP2PLUS |
| bool "TI OMAP2/3/4" |
| select COMMON_CLKDEV |
| help |
| "Systems based on omap24xx, omap34xx or omap44xx" |
| |
| config ARCH_OMAP2 |
| bool "TI OMAP2" |
| depends on ARCH_OMAP2PLUS |
| select CPU_V6 |
| |
| config ARCH_OMAP3 |
| bool "TI OMAP3" |
| depends on ARCH_OMAP2PLUS |
| select CPU_V7 |
| select USB_ARCH_HAS_EHCI |
| select ARM_L1_CACHE_SHIFT_6 |
| |
| config ARCH_OMAP4 |
| bool "TI OMAP4" |
| depends on ARCH_OMAP2PLUS |
| select CPU_V7 |
| select ARM_GIC |
| |
| endchoice |
| |
| comment "OMAP Feature Selections" |
| |
| config OMAP_DEBUG_DEVICES |
| bool |
| help |
| For debug cards on TI reference boards. |
| |
| config OMAP_DEBUG_LEDS |
| bool |
| depends on OMAP_DEBUG_DEVICES |
| default y if LEDS || LEDS_OMAP_DEBUG |
| |
| config OMAP_RESET_CLOCKS |
| bool "Reset unused clocks during boot" |
| depends on ARCH_OMAP |
| help |
| Say Y if you want to reset unused clocks during boot. |
| This option saves power, but assumes all drivers are |
| using the clock framework. Broken drivers that do not |
| yet use clock framework may not work with this option. |
| If you are booting from another operating system, you |
| probably do not want this option enabled until your |
| device drivers work properly. |
| |
| config OMAP_MUX |
| bool "OMAP multiplexing support" |
| depends on ARCH_OMAP |
| default y |
| help |
| Pin multiplexing support for OMAP boards. If your bootloader |
| sets the multiplexing correctly, say N. Otherwise, or if unsure, |
| say Y. |
| |
| config OMAP_MUX_DEBUG |
| bool "Multiplexing debug output" |
| depends on OMAP_MUX |
| help |
| Makes the multiplexing functions print out a lot of debug info. |
| This is useful if you want to find out the correct values of the |
| multiplexing registers. |
| |
| config OMAP_MUX_WARNINGS |
| bool "Warn about pins the bootloader didn't set up" |
| depends on OMAP_MUX |
| default y |
| help |
| Choose Y here to warn whenever driver initialization logic needs |
| to change the pin multiplexing setup. When there are no warnings |
| printed, it's safe to deselect OMAP_MUX for your product. |
| |
| config OMAP_MCBSP |
| bool "McBSP support" |
| depends on ARCH_OMAP |
| default y |
| help |
| Say Y here if you want support for the OMAP Multichannel |
| Buffered Serial Port. |
| |
| config OMAP_MBOX_FWK |
| tristate "Mailbox framework support" |
| depends on ARCH_OMAP |
| help |
| Say Y here if you want to use OMAP Mailbox framework support for |
| DSP, IVA1.0 and IVA2 in OMAP1/2/3. |
| |
| config OMAP_IOMMU |
| tristate |
| |
| config OMAP_IOMMU_DEBUG |
| depends on OMAP_IOMMU |
| tristate |
| |
| choice |
| prompt "System timer" |
| default OMAP_MPU_TIMER |
| |
| config OMAP_MPU_TIMER |
| bool "Use mpu timer" |
| help |
| Select this option if you want to use the OMAP mpu timer. This |
| timer provides more intra-tick resolution than the 32KHz timer, |
| but consumes more power. |
| |
| config OMAP_32K_TIMER |
| bool "Use 32KHz timer" |
| depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS |
| help |
| Select this option if you want to enable the OMAP 32KHz timer. |
| This timer saves power compared to the OMAP_MPU_TIMER, and has |
| support for no tick during idle. The 32KHz timer provides less |
| intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is |
| currently only available for OMAP16XX, 24XX, 34XX and OMAP4. |
| |
| endchoice |
| |
| config OMAP3_L2_AUX_SECURE_SAVE_RESTORE |
| bool "OMAP3 HS/EMU save and restore for L2 AUX control register" |
| depends on ARCH_OMAP3 && PM |
| default n |
| help |
| Without this option, L2 Auxiliary control register contents are |
| lost during off-mode entry on HS/EMU devices. This feature |
| requires support from PPA / boot-loader in HS/EMU devices, which |
| currently does not exist by default. |
| |
| config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID |
| int "Service ID for the support routine to set L2 AUX control" |
| depends on OMAP3_L2_AUX_SECURE_SAVE_RESTORE |
| default 43 |
| help |
| PPA routine service ID for setting L2 auxiliary control register. |
| |
| config OMAP_32K_TIMER_HZ |
| int "Kernel internal timer frequency for 32KHz timer" |
| range 32 1024 |
| depends on OMAP_32K_TIMER |
| default "128" |
| help |
| Kernel internal timer frequency should be a divisor of 32768, |
| such as 64 or 128. |
| |
| config OMAP_DM_TIMER |
| bool "Use dual-mode timer" |
| depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS |
| help |
| Select this option if you want to use OMAP Dual-Mode timers. |
| |
| config OMAP_SERIAL_WAKE |
| bool "Enable wake-up events for serial ports" |
| depends on ARCH_OMAP1 && OMAP_MUX |
| default y |
| help |
| Select this option if you want to have your system wake up |
| to data on the serial RX line. This allows you to wake the |
| system from serial console. |
| |
| choice |
| prompt "OMAP PM layer selection" |
| depends on ARCH_OMAP |
| default OMAP_PM_NOOP |
| |
| config OMAP_PM_NONE |
| bool "No PM layer" |
| |
| config OMAP_PM_NOOP |
| bool "No-op/debug PM layer" |
| |
| endchoice |
| |
| endmenu |
| |
| endif |