chelsio: Use netdev_<level> and pr_<level>
Use more current logging styles.
Convert printks to pr_<level> and
printks with ("%s: ...", dev->name to netdev_<level>(dev, "...
Add pr_fmt #defines where appropriate.
Coalesce formats.
Use pr_<level>_once where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/chelsio/cxgb/cxgb2.c b/drivers/net/ethernet/chelsio/cxgb/cxgb2.c
index c8fdeaa..20d2085 100644
--- a/drivers/net/ethernet/chelsio/cxgb/cxgb2.c
+++ b/drivers/net/ethernet/chelsio/cxgb/cxgb2.c
@@ -131,7 +131,7 @@
static void link_report(struct port_info *p)
{
if (!netif_carrier_ok(p->dev))
- printk(KERN_INFO "%s: link down\n", p->dev->name);
+ netdev_info(p->dev, "link down\n");
else {
const char *s = "10Mbps";
@@ -141,9 +141,9 @@
case SPEED_100: s = "100Mbps"; break;
}
- printk(KERN_INFO "%s: link up, %s, %s-duplex\n",
- p->dev->name, s,
- p->link_config.duplex == DUPLEX_FULL ? "full" : "half");
+ netdev_info(p->dev, "link up, %s, %s-duplex\n",
+ s, p->link_config.duplex == DUPLEX_FULL
+ ? "full" : "half");
}
}
@@ -976,19 +976,13 @@
static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
- static int version_printed;
-
int i, err, pci_using_dac = 0;
unsigned long mmio_start, mmio_len;
const struct board_info *bi;
struct adapter *adapter = NULL;
struct port_info *pi;
- if (!version_printed) {
- printk(KERN_INFO "%s - version %s\n", DRV_DESCRIPTION,
- DRV_VERSION);
- ++version_printed;
- }
+ pr_info_once("%s - version %s\n", DRV_DESCRIPTION, DRV_VERSION);
err = pci_enable_device(pdev);
if (err)
@@ -1124,8 +1118,8 @@
for (i = 0; i < bi->port_number; ++i) {
err = register_netdev(adapter->port[i].dev);
if (err)
- pr_warning("%s: cannot register net device %s, skipping\n",
- pci_name(pdev), adapter->port[i].dev->name);
+ pr_warn("%s: cannot register net device %s, skipping\n",
+ pci_name(pdev), adapter->port[i].dev->name);
else {
/*
* Change the name we use for messages to the name of
@@ -1143,10 +1137,10 @@
goto out_release_adapter_res;
}
- printk(KERN_INFO "%s: %s (rev %d), %s %dMHz/%d-bit\n", adapter->name,
- bi->desc, adapter->params.chip_revision,
- adapter->params.pci.is_pcix ? "PCIX" : "PCI",
- adapter->params.pci.speed, adapter->params.pci.width);
+ pr_info("%s: %s (rev %d), %s %dMHz/%d-bit\n",
+ adapter->name, bi->desc, adapter->params.chip_revision,
+ adapter->params.pci.is_pcix ? "PCIX" : "PCI",
+ adapter->params.pci.speed, adapter->params.pci.width);
/*
* Set the T1B ASIC and memory clocks.