hwmon: (adm9240) Avoid forward declaration
Reorder functions to avoid forward declaration.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
diff --git a/drivers/hwmon/adm9240.c b/drivers/hwmon/adm9240.c
index 086d02a..8235ae4 100644
--- a/drivers/hwmon/adm9240.c
+++ b/drivers/hwmon/adm9240.c
@@ -130,35 +130,6 @@
return SCALE(reg, 1250, 255);
}
-static int adm9240_probe(struct i2c_client *client,
- const struct i2c_device_id *id);
-static int adm9240_detect(struct i2c_client *client,
- struct i2c_board_info *info);
-static void adm9240_init_client(struct i2c_client *client);
-static int adm9240_remove(struct i2c_client *client);
-static struct adm9240_data *adm9240_update_device(struct device *dev);
-
-/* driver data */
-static const struct i2c_device_id adm9240_id[] = {
- { "adm9240", adm9240 },
- { "ds1780", ds1780 },
- { "lm81", lm81 },
- { }
-};
-MODULE_DEVICE_TABLE(i2c, adm9240_id);
-
-static struct i2c_driver adm9240_driver = {
- .class = I2C_CLASS_HWMON,
- .driver = {
- .name = "adm9240",
- },
- .probe = adm9240_probe,
- .remove = adm9240_remove,
- .id_table = adm9240_id,
- .detect = adm9240_detect,
- .address_list = normal_i2c,
-};
-
/* per client data */
struct adm9240_data {
struct device *hwmon_dev;
@@ -181,6 +152,110 @@
u8 vrm; /* -- vrm set on startup, no accessor */
};
+/* write new fan div, callers must hold data->update_lock */
+static void adm9240_write_fan_div(struct i2c_client *client, int nr,
+ u8 fan_div)
+{
+ u8 reg, old, shift = (nr + 2) * 2;
+
+ reg = i2c_smbus_read_byte_data(client, ADM9240_REG_VID_FAN_DIV);
+ old = (reg >> shift) & 3;
+ reg &= ~(3 << shift);
+ reg |= (fan_div << shift);
+ i2c_smbus_write_byte_data(client, ADM9240_REG_VID_FAN_DIV, reg);
+ dev_dbg(&client->dev,
+ "fan%d clock divider changed from %u to %u\n",
+ nr + 1, 1 << old, 1 << fan_div);
+}
+
+static struct adm9240_data *adm9240_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm9240_data *data = i2c_get_clientdata(client);
+ int i;
+
+ mutex_lock(&data->update_lock);
+
+ /* minimum measurement cycle: 1.75 seconds */
+ if (time_after(jiffies, data->last_updated_measure + (HZ * 7 / 4))
+ || !data->valid) {
+
+ for (i = 0; i < 6; i++) { /* read voltages */
+ data->in[i] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_IN(i));
+ }
+ data->alarms = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_INT(0)) |
+ i2c_smbus_read_byte_data(client,
+ ADM9240_REG_INT(1)) << 8;
+
+ /*
+ * read temperature: assume temperature changes less than
+ * 0.5'C per two measurement cycles thus ignore possible
+ * but unlikely aliasing error on lsb reading. --Grant
+ */
+ data->temp = ((i2c_smbus_read_byte_data(client,
+ ADM9240_REG_TEMP) << 8) |
+ i2c_smbus_read_byte_data(client,
+ ADM9240_REG_TEMP_CONF)) / 128;
+
+ for (i = 0; i < 2; i++) { /* read fans */
+ data->fan[i] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_FAN(i));
+
+ /* adjust fan clock divider on overflow */
+ if (data->valid && data->fan[i] == 255 &&
+ data->fan_div[i] < 3) {
+
+ adm9240_write_fan_div(client, i,
+ ++data->fan_div[i]);
+
+ /* adjust fan_min if active, but not to 0 */
+ if (data->fan_min[i] < 255 &&
+ data->fan_min[i] >= 2)
+ data->fan_min[i] /= 2;
+ }
+ }
+ data->last_updated_measure = jiffies;
+ }
+
+ /* minimum config reading cycle: 300 seconds */
+ if (time_after(jiffies, data->last_updated_config + (HZ * 300))
+ || !data->valid) {
+
+ for (i = 0; i < 6; i++) {
+ data->in_min[i] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_IN_MIN(i));
+ data->in_max[i] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_IN_MAX(i));
+ }
+ for (i = 0; i < 2; i++) {
+ data->fan_min[i] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_FAN_MIN(i));
+ }
+ data->temp_max[0] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_TEMP_MAX(0));
+ data->temp_max[1] = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_TEMP_MAX(1));
+
+ /* read fan divs and 5-bit VID */
+ i = i2c_smbus_read_byte_data(client, ADM9240_REG_VID_FAN_DIV);
+ data->fan_div[0] = (i >> 4) & 3;
+ data->fan_div[1] = (i >> 6) & 3;
+ data->vid = i & 0x0f;
+ data->vid |= (i2c_smbus_read_byte_data(client,
+ ADM9240_REG_VID4) & 1) << 4;
+ /* read analog out */
+ data->aout = i2c_smbus_read_byte_data(client,
+ ADM9240_REG_ANALOG_OUT);
+
+ data->last_updated_config = jiffies;
+ data->valid = 1;
+ }
+ mutex_unlock(&data->update_lock);
+ return data;
+}
+
/*** sysfs accessors ***/
/* temperature */
@@ -340,22 +415,6 @@
return sprintf(buf, "%d\n", 1 << data->fan_div[attr->index]);
}
-/* write new fan div, callers must hold data->update_lock */
-static void adm9240_write_fan_div(struct i2c_client *client, int nr,
- u8 fan_div)
-{
- u8 reg, old, shift = (nr + 2) * 2;
-
- reg = i2c_smbus_read_byte_data(client, ADM9240_REG_VID_FAN_DIV);
- old = (reg >> shift) & 3;
- reg &= ~(3 << shift);
- reg |= (fan_div << shift);
- i2c_smbus_write_byte_data(client, ADM9240_REG_VID_FAN_DIV, reg);
- dev_dbg(&client->dev,
- "fan%d clock divider changed from %u to %u\n",
- nr + 1, 1 << old, 1 << fan_div);
-}
-
/*
* set fan speed low limit:
*
@@ -620,6 +679,48 @@
return 0;
}
+static void adm9240_init_client(struct i2c_client *client)
+{
+ struct adm9240_data *data = i2c_get_clientdata(client);
+ u8 conf = i2c_smbus_read_byte_data(client, ADM9240_REG_CONFIG);
+ u8 mode = i2c_smbus_read_byte_data(client, ADM9240_REG_TEMP_CONF) & 3;
+
+ data->vrm = vid_which_vrm(); /* need this to report vid as mV */
+
+ dev_info(&client->dev, "Using VRM: %d.%d\n", data->vrm / 10,
+ data->vrm % 10);
+
+ if (conf & 1) { /* measurement cycle running: report state */
+
+ dev_info(&client->dev, "status: config 0x%02x mode %u\n",
+ conf, mode);
+
+ } else { /* cold start: open limits before starting chip */
+ int i;
+
+ for (i = 0; i < 6; i++) {
+ i2c_smbus_write_byte_data(client,
+ ADM9240_REG_IN_MIN(i), 0);
+ i2c_smbus_write_byte_data(client,
+ ADM9240_REG_IN_MAX(i), 255);
+ }
+ i2c_smbus_write_byte_data(client,
+ ADM9240_REG_FAN_MIN(0), 255);
+ i2c_smbus_write_byte_data(client,
+ ADM9240_REG_FAN_MIN(1), 255);
+ i2c_smbus_write_byte_data(client,
+ ADM9240_REG_TEMP_MAX(0), 127);
+ i2c_smbus_write_byte_data(client,
+ ADM9240_REG_TEMP_MAX(1), 127);
+
+ /* start measurement cycle */
+ i2c_smbus_write_byte_data(client, ADM9240_REG_CONFIG, 1);
+
+ dev_info(&client->dev,
+ "cold start: config was 0x%02x mode %u\n", conf, mode);
+ }
+}
+
static int adm9240_probe(struct i2c_client *new_client,
const struct i2c_device_id *id)
{
@@ -663,135 +764,25 @@
return 0;
}
-static void adm9240_init_client(struct i2c_client *client)
-{
- struct adm9240_data *data = i2c_get_clientdata(client);
- u8 conf = i2c_smbus_read_byte_data(client, ADM9240_REG_CONFIG);
- u8 mode = i2c_smbus_read_byte_data(client, ADM9240_REG_TEMP_CONF) & 3;
+static const struct i2c_device_id adm9240_id[] = {
+ { "adm9240", adm9240 },
+ { "ds1780", ds1780 },
+ { "lm81", lm81 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, adm9240_id);
- data->vrm = vid_which_vrm(); /* need this to report vid as mV */
-
- dev_info(&client->dev, "Using VRM: %d.%d\n", data->vrm / 10,
- data->vrm % 10);
-
- if (conf & 1) { /* measurement cycle running: report state */
-
- dev_info(&client->dev, "status: config 0x%02x mode %u\n",
- conf, mode);
-
- } else { /* cold start: open limits before starting chip */
- int i;
-
- for (i = 0; i < 6; i++) {
- i2c_smbus_write_byte_data(client,
- ADM9240_REG_IN_MIN(i), 0);
- i2c_smbus_write_byte_data(client,
- ADM9240_REG_IN_MAX(i), 255);
- }
- i2c_smbus_write_byte_data(client,
- ADM9240_REG_FAN_MIN(0), 255);
- i2c_smbus_write_byte_data(client,
- ADM9240_REG_FAN_MIN(1), 255);
- i2c_smbus_write_byte_data(client,
- ADM9240_REG_TEMP_MAX(0), 127);
- i2c_smbus_write_byte_data(client,
- ADM9240_REG_TEMP_MAX(1), 127);
-
- /* start measurement cycle */
- i2c_smbus_write_byte_data(client, ADM9240_REG_CONFIG, 1);
-
- dev_info(&client->dev,
- "cold start: config was 0x%02x mode %u\n", conf, mode);
- }
-}
-
-static struct adm9240_data *adm9240_update_device(struct device *dev)
-{
- struct i2c_client *client = to_i2c_client(dev);
- struct adm9240_data *data = i2c_get_clientdata(client);
- int i;
-
- mutex_lock(&data->update_lock);
-
- /* minimum measurement cycle: 1.75 seconds */
- if (time_after(jiffies, data->last_updated_measure + (HZ * 7 / 4))
- || !data->valid) {
-
- for (i = 0; i < 6; i++) { /* read voltages */
- data->in[i] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_IN(i));
- }
- data->alarms = i2c_smbus_read_byte_data(client,
- ADM9240_REG_INT(0)) |
- i2c_smbus_read_byte_data(client,
- ADM9240_REG_INT(1)) << 8;
-
- /*
- * read temperature: assume temperature changes less than
- * 0.5'C per two measurement cycles thus ignore possible
- * but unlikely aliasing error on lsb reading. --Grant
- */
- data->temp = ((i2c_smbus_read_byte_data(client,
- ADM9240_REG_TEMP) << 8) |
- i2c_smbus_read_byte_data(client,
- ADM9240_REG_TEMP_CONF)) / 128;
-
- for (i = 0; i < 2; i++) { /* read fans */
- data->fan[i] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_FAN(i));
-
- /* adjust fan clock divider on overflow */
- if (data->valid && data->fan[i] == 255 &&
- data->fan_div[i] < 3) {
-
- adm9240_write_fan_div(client, i,
- ++data->fan_div[i]);
-
- /* adjust fan_min if active, but not to 0 */
- if (data->fan_min[i] < 255 &&
- data->fan_min[i] >= 2)
- data->fan_min[i] /= 2;
- }
- }
- data->last_updated_measure = jiffies;
- }
-
- /* minimum config reading cycle: 300 seconds */
- if (time_after(jiffies, data->last_updated_config + (HZ * 300))
- || !data->valid) {
-
- for (i = 0; i < 6; i++) {
- data->in_min[i] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_IN_MIN(i));
- data->in_max[i] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_IN_MAX(i));
- }
- for (i = 0; i < 2; i++) {
- data->fan_min[i] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_FAN_MIN(i));
- }
- data->temp_max[0] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_TEMP_MAX(0));
- data->temp_max[1] = i2c_smbus_read_byte_data(client,
- ADM9240_REG_TEMP_MAX(1));
-
- /* read fan divs and 5-bit VID */
- i = i2c_smbus_read_byte_data(client, ADM9240_REG_VID_FAN_DIV);
- data->fan_div[0] = (i >> 4) & 3;
- data->fan_div[1] = (i >> 6) & 3;
- data->vid = i & 0x0f;
- data->vid |= (i2c_smbus_read_byte_data(client,
- ADM9240_REG_VID4) & 1) << 4;
- /* read analog out */
- data->aout = i2c_smbus_read_byte_data(client,
- ADM9240_REG_ANALOG_OUT);
-
- data->last_updated_config = jiffies;
- data->valid = 1;
- }
- mutex_unlock(&data->update_lock);
- return data;
-}
+static struct i2c_driver adm9240_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "adm9240",
+ },
+ .probe = adm9240_probe,
+ .remove = adm9240_remove,
+ .id_table = adm9240_id,
+ .detect = adm9240_detect,
+ .address_list = normal_i2c,
+};
module_i2c_driver(adm9240_driver);