pcmcia: introduce autoconfiguration feature
Introduce an autoconfiguration feature to set certain values in
pcmcia_loop_config(), instead of copying the same code over and over
in each PCMCIA driver. At first, introduce the following options:
CONF_AUTO_CHECK_VCC check or matching Vcc entry
CONF_AUTO_SET_VPP set Vpp
CONF_AUTO_AUDIO enable the speaker line
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> (for drivers/bluetooth)
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/net/wireless/hostap/hostap_cs.c b/drivers/net/wireless/hostap/hostap_cs.c
index 5b0b582..d4f19af 100644
--- a/drivers/net/wireless/hostap/hostap_cs.c
+++ b/drivers/net/wireless/hostap/hostap_cs.c
@@ -472,7 +472,6 @@
static int prism2_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
@@ -481,28 +480,6 @@
PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X "
"(default 0x%02X)\n", cfg->index, dflt->index);
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO)
- p_dev->config_flags |= CONF_ENABLE_SPKR;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != cfg->vcc.param[CISTPL_POWER_VNOM] /
- 10000 && !ignore_cis_vcc) {
- PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping"
- " this entry\n");
- return -ENODEV;
- }
- } else if (dflt->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != dflt->vcc.param[CISTPL_POWER_VNOM] /
- 10000 && !ignore_cis_vcc) {
- PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch "
- "- skipping this entry\n");
- return -ENODEV;
- }
- }
-
if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
p_dev->vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
else if (dflt->vpp1.present & (1 << CISTPL_POWER_VNOM))
@@ -553,6 +530,10 @@
}
/* Look for an appropriate configuration table entry in the CIS */
+ link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_AUDIO |
+ CONF_AUTO_CHECK_VCC;
+ if (ignore_cis_vcc)
+ link->config_flags &= ~CONF_AUTO_CHECK_VCC;
ret = pcmcia_loop_config(link, prism2_config_check, NULL);
if (ret) {
if (!ignore_cis_vcc)