gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2
Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
it is different from PCA9535 and includes interrupt mask/status registers,
The current driver does not support the interrupt registers configuration,
it causes some gpio pins cannot trigger interrupt events,
this patch fix this issue.
The original patch was submitted by
Josef Ahmad <josef.ahmad@linux.intel.com>
http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipes-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch
Signed-off-by: Yong Li <yong.b.li@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c
index d0d3065..8d8f06d 100644
--- a/drivers/gpio/gpio-pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -37,8 +37,13 @@
#define PCA957X_MSK 6
#define PCA957X_INTS 7
+#define PCAL953X_IN_LATCH 34
+#define PCAL953X_INT_MASK 37
+#define PCAL953X_INT_STAT 38
+
#define PCA_GPIO_MASK 0x00FF
#define PCA_INT 0x0100
+#define PCA_PCAL 0x0200
#define PCA953X_TYPE 0x1000
#define PCA957X_TYPE 0x2000
#define PCA_TYPE_MASK 0xF000
@@ -76,7 +81,7 @@
MODULE_DEVICE_TABLE(i2c, pca953x_id);
static const struct acpi_device_id pca953x_acpi_ids[] = {
- { "INT3491", 16 | PCA953X_TYPE | PCA_INT, },
+ { "INT3491", 16 | PCA953X_TYPE | PCA_INT | PCA_PCAL, },
{ }
};
MODULE_DEVICE_TABLE(acpi, pca953x_acpi_ids);
@@ -436,6 +441,18 @@
struct pca953x_chip *chip = gpiochip_get_data(gc);
u8 new_irqs;
int level, i;
+ u8 invert_irq_mask[MAX_BANK];
+
+ if (chip->driver_data & PCA_PCAL) {
+ /* Enable latch on interrupt-enabled inputs */
+ pca953x_write_regs(chip, PCAL953X_IN_LATCH, chip->irq_mask);
+
+ for (i = 0; i < NBANK(chip); i++)
+ invert_irq_mask[i] = ~chip->irq_mask[i];
+
+ /* Unmask enabled interrupts */
+ pca953x_write_regs(chip, PCAL953X_INT_MASK, invert_irq_mask);
+ }
/* Look for any newly setup interrupt */
for (i = 0; i < NBANK(chip); i++) {
@@ -497,6 +514,29 @@
u8 trigger[MAX_BANK];
int ret, i, offset = 0;
+ if (chip->driver_data & PCA_PCAL) {
+ /* Read the current interrupt status from the device */
+ ret = pca953x_read_regs(chip, PCAL953X_INT_STAT, trigger);
+ if (ret)
+ return false;
+
+ /* Check latched inputs and clear interrupt status */
+ ret = pca953x_read_regs(chip, PCA953X_INPUT, cur_stat);
+ if (ret)
+ return false;
+
+ for (i = 0; i < NBANK(chip); i++) {
+ /* Apply filter for rising/falling edge selection */
+ pending[i] = (~cur_stat[i] & chip->irq_trig_fall[i]) |
+ (cur_stat[i] & chip->irq_trig_raise[i]);
+ pending[i] &= trigger[i];
+ if (pending[i])
+ pending_seen = true;
+ }
+
+ return pending_seen;
+ }
+
switch (chip->chip_type) {
case PCA953X_TYPE:
offset = PCA953X_INPUT;