Merge commit 'v2.6.36-rc7' into spi/next
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index bc9a42d..0c936cf 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -172,18 +172,12 @@
}
static struct pl022_config_chip spi0_chip_info = {
- .lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
- .endian_tx = SSP_TX_LSB,
- .endian_rx = SSP_RX_LSB,
- .data_size = SSP_DATA_BITS_8,
.rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_FIRST_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_LOW,
.ctrl_len = SSP_BITS_8,
.wait_state = SSP_MWIRE_WAIT_ZERO,
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -239,6 +233,7 @@
.max_speed_hz = 5000000,
.bus_num = 0,
.chip_select = 0,
+ .mode = SPI_MODE_0,
.platform_data = &eeprom,
.controller_data = &spi0_chip_info,
},
diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c
index 5f55012..03f7936 100644
--- a/arch/arm/mach-u300/dummyspichip.c
+++ b/arch/arm/mach-u300/dummyspichip.c
@@ -46,7 +46,6 @@
* struct, this is just used here to alter the behaviour of the chip
* in order to perform tests.
*/
- struct pl022_config_chip *chip_info = spi->controller_data;
int status;
u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
@@ -72,7 +71,7 @@
* Force chip to 8 bit mode
* WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
*/
- chip_info->data_size = SSP_DATA_BITS_8;
+ spi->bits_per_word = 8;
/* You should NOT DO THIS EITHER */
spi->master->setup(spi);
@@ -159,7 +158,7 @@
* Force chip to 16 bit mode
* WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
*/
- chip_info->data_size = SSP_DATA_BITS_16;
+ spi->bits_per_word = 16;
/* You should NOT DO THIS EITHER */
spi->master->setup(spi);
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index f0e887b..edb2c0d 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -30,8 +30,6 @@
}
struct pl022_config_chip dummy_chip_info = {
- /* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
- .lbm = LOOPBACK_ENABLED,
/*
* available POLLING_TRANSFER and INTERRUPT_TRANSFER,
* DMA_TRANSFER does not work
@@ -42,14 +40,8 @@
.hierarchy = SSP_MASTER,
/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
.slave_tx_disable = 0,
- /* LSB first */
- .endian_tx = SSP_TX_LSB,
- .endian_rx = SSP_RX_LSB,
- .data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_SECOND_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_LOW,
.ctrl_len = SSP_BITS_12,
.wait_state = SSP_MWIRE_WAIT_ZERO,
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -75,7 +67,7 @@
.bus_num = 0, /* Only one bus on this chip */
.chip_select = 0,
/* Means SPI_CS_HIGH, change if e.g low CS */
- .mode = 0,
+ .mode = SPI_MODE_1 | SPI_LSB_FIRST | SPI_LOOP,
},
#endif
};
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 0e8fd13..219ae0c 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -55,19 +55,13 @@
}
struct pl022_config_chip ab4500_chip_info = {
- .lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
/* we can act as master only */
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
- .endian_rx = SSP_RX_MSB,
- .endian_tx = SSP_TX_MSB,
- .data_size = SSP_DATA_BITS_24,
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_SECOND_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_HIGH,
.cs_control = ab4500_spi_cs_control,
};
@@ -83,7 +77,7 @@
.max_speed_hz = 12000000,
.bus_num = 0,
.chip_select = 0,
- .mode = SPI_MODE_0,
+ .mode = SPI_MODE_3,
.irq = IRQ_DB8500_AB8500,
},
};
diff --git a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
index e5aba8f..b226f740 100644
--- a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
+++ b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
@@ -32,6 +32,8 @@
* struct s3c64xx_spi_info - SPI Controller defining structure
* @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
* @src_clk_name: Platform name of the corresponding clock.
+ * @clk_from_cmu: If the SPI clock/prescalar control block is present
+ * by the platform's clock-management-unit and not in SPI controller.
* @num_cs: Number of CS this controller emulates.
* @cfg_gpio: Configure pins for this SPI controller.
* @fifo_lvl_mask: All tx fifo_lvl fields start at offset-6
@@ -41,6 +43,7 @@
struct s3c64xx_spi_info {
int src_clk_nr;
char *src_clk_name;
+ bool clk_from_cmu;
int num_cs;
diff --git a/drivers/mfd/ab8500-spi.c b/drivers/mfd/ab8500-spi.c
index e1c8b62..01b6d58 100644
--- a/drivers/mfd/ab8500-spi.c
+++ b/drivers/mfd/ab8500-spi.c
@@ -83,6 +83,11 @@
struct ab8500 *ab8500;
int ret;
+ spi->bits_per_word = 24;
+ ret = spi_setup(spi);
+ if (ret < 0)
+ return ret;
+
ab8500 = kzalloc(sizeof *ab8500, GFP_KERNEL);
if (!ab8500)
return -ENOMEM;
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 91c2f4f..d966de1 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -298,6 +298,13 @@
help
SPI driver for Freescale STMP37xx/378x SoC SSP interface
+config SPI_TOPCLIFF_PCH
+ tristate "Topcliff PCH SPI Controller"
+ depends on PCI
+ help
+ SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
+ used in some x86 embedded processors.
+
config SPI_TXX9
tristate "Toshiba TXx9 SPI controller"
depends on GENERIC_GPIO && CPU_TX49XX
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index e9cbd18..f32d11e 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -2,9 +2,7 @@
# Makefile for kernel SPI drivers.
#
-ifeq ($(CONFIG_SPI_DEBUG),y)
-EXTRA_CFLAGS += -DDEBUG
-endif
+ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG
# small core, mostly translating board-specific
# config declarations into driver model code
@@ -39,6 +37,7 @@
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
+obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi_topcliff_pch.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o
diff --git a/drivers/spi/amba-pl022.c b/drivers/spi/amba-pl022.c
index 4c37c4e2..fb3d1b3 100644
--- a/drivers/spi/amba-pl022.c
+++ b/drivers/spi/amba-pl022.c
@@ -27,7 +27,6 @@
/*
* TODO:
* - add timeout on polled transfers
- * - add generic DMA framework support
*/
#include <linux/init.h>
@@ -45,6 +44,9 @@
#include <linux/amba/pl022.h>
#include <linux/io.h>
#include <linux/slab.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
/*
* This macro is used to define some register default values.
@@ -381,6 +383,14 @@
enum ssp_reading read;
enum ssp_writing write;
u32 exp_fifo_level;
+ /* DMA settings */
+#ifdef CONFIG_DMA_ENGINE
+ struct dma_chan *dma_rx_channel;
+ struct dma_chan *dma_tx_channel;
+ struct sg_table sgt_rx;
+ struct sg_table sgt_tx;
+ char *dummypage;
+#endif
};
/**
@@ -406,7 +416,7 @@
u16 dmacr;
u16 cpsr;
u8 n_bytes;
- u8 enable_dma:1;
+ bool enable_dma;
enum ssp_reading read;
enum ssp_writing write;
void (*cs_control) (u32 command);
@@ -763,6 +773,371 @@
}
return STATE_DONE;
}
+
+/*
+ * This DMA functionality is only compiled in if we have
+ * access to the generic DMA devices/DMA engine.
+ */
+#ifdef CONFIG_DMA_ENGINE
+static void unmap_free_dma_scatter(struct pl022 *pl022)
+{
+ /* Unmap and free the SG tables */
+ dma_unmap_sg(&pl022->adev->dev, pl022->sgt_tx.sgl,
+ pl022->sgt_tx.nents, DMA_TO_DEVICE);
+ dma_unmap_sg(&pl022->adev->dev, pl022->sgt_rx.sgl,
+ pl022->sgt_rx.nents, DMA_FROM_DEVICE);
+ sg_free_table(&pl022->sgt_rx);
+ sg_free_table(&pl022->sgt_tx);
+}
+
+static void dma_callback(void *data)
+{
+ struct pl022 *pl022 = data;
+ struct spi_message *msg = pl022->cur_msg;
+
+ BUG_ON(!pl022->sgt_rx.sgl);
+
+#ifdef VERBOSE_DEBUG
+ /*
+ * Optionally dump out buffers to inspect contents, this is
+ * good if you want to convince yourself that the loopback
+ * read/write contents are the same, when adopting to a new
+ * DMA engine.
+ */
+ {
+ struct scatterlist *sg;
+ unsigned int i;
+
+ dma_sync_sg_for_cpu(&pl022->adev->dev,
+ pl022->sgt_rx.sgl,
+ pl022->sgt_rx.nents,
+ DMA_FROM_DEVICE);
+
+ for_each_sg(pl022->sgt_rx.sgl, sg, pl022->sgt_rx.nents, i) {
+ dev_dbg(&pl022->adev->dev, "SPI RX SG ENTRY: %d", i);
+ print_hex_dump(KERN_ERR, "SPI RX: ",
+ DUMP_PREFIX_OFFSET,
+ 16,
+ 1,
+ sg_virt(sg),
+ sg_dma_len(sg),
+ 1);
+ }
+ for_each_sg(pl022->sgt_tx.sgl, sg, pl022->sgt_tx.nents, i) {
+ dev_dbg(&pl022->adev->dev, "SPI TX SG ENTRY: %d", i);
+ print_hex_dump(KERN_ERR, "SPI TX: ",
+ DUMP_PREFIX_OFFSET,
+ 16,
+ 1,
+ sg_virt(sg),
+ sg_dma_len(sg),
+ 1);
+ }
+ }
+#endif
+
+ unmap_free_dma_scatter(pl022);
+
+ /* Update total bytes transfered */
+ msg->actual_length += pl022->cur_transfer->len;
+ if (pl022->cur_transfer->cs_change)
+ pl022->cur_chip->
+ cs_control(SSP_CHIP_DESELECT);
+
+ /* Move to next transfer */
+ msg->state = next_transfer(pl022);
+ tasklet_schedule(&pl022->pump_transfers);
+}
+
+static void setup_dma_scatter(struct pl022 *pl022,
+ void *buffer,
+ unsigned int length,
+ struct sg_table *sgtab)
+{
+ struct scatterlist *sg;
+ int bytesleft = length;
+ void *bufp = buffer;
+ int mapbytes;
+ int i;
+
+ if (buffer) {
+ for_each_sg(sgtab->sgl, sg, sgtab->nents, i) {
+ /*
+ * If there are less bytes left than what fits
+ * in the current page (plus page alignment offset)
+ * we just feed in this, else we stuff in as much
+ * as we can.
+ */
+ if (bytesleft < (PAGE_SIZE - offset_in_page(bufp)))
+ mapbytes = bytesleft;
+ else
+ mapbytes = PAGE_SIZE - offset_in_page(bufp);
+ sg_set_page(sg, virt_to_page(bufp),
+ mapbytes, offset_in_page(bufp));
+ bufp += mapbytes;
+ bytesleft -= mapbytes;
+ dev_dbg(&pl022->adev->dev,
+ "set RX/TX target page @ %p, %d bytes, %d left\n",
+ bufp, mapbytes, bytesleft);
+ }
+ } else {
+ /* Map the dummy buffer on every page */
+ for_each_sg(sgtab->sgl, sg, sgtab->nents, i) {
+ if (bytesleft < PAGE_SIZE)
+ mapbytes = bytesleft;
+ else
+ mapbytes = PAGE_SIZE;
+ sg_set_page(sg, virt_to_page(pl022->dummypage),
+ mapbytes, 0);
+ bytesleft -= mapbytes;
+ dev_dbg(&pl022->adev->dev,
+ "set RX/TX to dummy page %d bytes, %d left\n",
+ mapbytes, bytesleft);
+
+ }
+ }
+ BUG_ON(bytesleft);
+}
+
+/**
+ * configure_dma - configures the channels for the next transfer
+ * @pl022: SSP driver's private data structure
+ */
+static int configure_dma(struct pl022 *pl022)
+{
+ struct dma_slave_config rx_conf = {
+ .src_addr = SSP_DR(pl022->phybase),
+ .direction = DMA_FROM_DEVICE,
+ .src_maxburst = pl022->vendor->fifodepth >> 1,
+ };
+ struct dma_slave_config tx_conf = {
+ .dst_addr = SSP_DR(pl022->phybase),
+ .direction = DMA_TO_DEVICE,
+ .dst_maxburst = pl022->vendor->fifodepth >> 1,
+ };
+ unsigned int pages;
+ int ret;
+ int sglen;
+ struct dma_chan *rxchan = pl022->dma_rx_channel;
+ struct dma_chan *txchan = pl022->dma_tx_channel;
+ struct dma_async_tx_descriptor *rxdesc;
+ struct dma_async_tx_descriptor *txdesc;
+ dma_cookie_t cookie;
+
+ /* Check that the channels are available */
+ if (!rxchan || !txchan)
+ return -ENODEV;
+
+ switch (pl022->read) {
+ case READING_NULL:
+ /* Use the same as for writing */
+ rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED;
+ break;
+ case READING_U8:
+ rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ break;
+ case READING_U16:
+ rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ break;
+ case READING_U32:
+ rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ break;
+ }
+
+ switch (pl022->write) {
+ case WRITING_NULL:
+ /* Use the same as for reading */
+ tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED;
+ break;
+ case WRITING_U8:
+ tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ break;
+ case WRITING_U16:
+ tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ break;
+ case WRITING_U32:
+ tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;;
+ break;
+ }
+
+ /* SPI pecularity: we need to read and write the same width */
+ if (rx_conf.src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
+ rx_conf.src_addr_width = tx_conf.dst_addr_width;
+ if (tx_conf.dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
+ tx_conf.dst_addr_width = rx_conf.src_addr_width;
+ BUG_ON(rx_conf.src_addr_width != tx_conf.dst_addr_width);
+
+ rxchan->device->device_control(rxchan, DMA_SLAVE_CONFIG,
+ (unsigned long) &rx_conf);
+ txchan->device->device_control(txchan, DMA_SLAVE_CONFIG,
+ (unsigned long) &tx_conf);
+
+ /* Create sglists for the transfers */
+ pages = (pl022->cur_transfer->len >> PAGE_SHIFT) + 1;
+ dev_dbg(&pl022->adev->dev, "using %d pages for transfer\n", pages);
+
+ ret = sg_alloc_table(&pl022->sgt_rx, pages, GFP_KERNEL);
+ if (ret)
+ goto err_alloc_rx_sg;
+
+ ret = sg_alloc_table(&pl022->sgt_tx, pages, GFP_KERNEL);
+ if (ret)
+ goto err_alloc_tx_sg;
+
+ /* Fill in the scatterlists for the RX+TX buffers */
+ setup_dma_scatter(pl022, pl022->rx,
+ pl022->cur_transfer->len, &pl022->sgt_rx);
+ setup_dma_scatter(pl022, pl022->tx,
+ pl022->cur_transfer->len, &pl022->sgt_tx);
+
+ /* Map DMA buffers */
+ sglen = dma_map_sg(&pl022->adev->dev, pl022->sgt_rx.sgl,
+ pl022->sgt_rx.nents, DMA_FROM_DEVICE);
+ if (!sglen)
+ goto err_rx_sgmap;
+
+ sglen = dma_map_sg(&pl022->adev->dev, pl022->sgt_tx.sgl,
+ pl022->sgt_tx.nents, DMA_TO_DEVICE);
+ if (!sglen)
+ goto err_tx_sgmap;
+
+ /* Send both scatterlists */
+ rxdesc = rxchan->device->device_prep_slave_sg(rxchan,
+ pl022->sgt_rx.sgl,
+ pl022->sgt_rx.nents,
+ DMA_FROM_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!rxdesc)
+ goto err_rxdesc;
+
+ txdesc = txchan->device->device_prep_slave_sg(txchan,
+ pl022->sgt_tx.sgl,
+ pl022->sgt_tx.nents,
+ DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!txdesc)
+ goto err_txdesc;
+
+ /* Put the callback on the RX transfer only, that should finish last */
+ rxdesc->callback = dma_callback;
+ rxdesc->callback_param = pl022;
+
+ /* Submit and fire RX and TX with TX last so we're ready to read! */
+ cookie = rxdesc->tx_submit(rxdesc);
+ if (dma_submit_error(cookie))
+ goto err_submit_rx;
+ cookie = txdesc->tx_submit(txdesc);
+ if (dma_submit_error(cookie))
+ goto err_submit_tx;
+ rxchan->device->device_issue_pending(rxchan);
+ txchan->device->device_issue_pending(txchan);
+
+ return 0;
+
+err_submit_tx:
+err_submit_rx:
+err_txdesc:
+ txchan->device->device_control(txchan, DMA_TERMINATE_ALL, 0);
+err_rxdesc:
+ rxchan->device->device_control(rxchan, DMA_TERMINATE_ALL, 0);
+ dma_unmap_sg(&pl022->adev->dev, pl022->sgt_tx.sgl,
+ pl022->sgt_tx.nents, DMA_TO_DEVICE);
+err_tx_sgmap:
+ dma_unmap_sg(&pl022->adev->dev, pl022->sgt_rx.sgl,
+ pl022->sgt_tx.nents, DMA_FROM_DEVICE);
+err_rx_sgmap:
+ sg_free_table(&pl022->sgt_tx);
+err_alloc_tx_sg:
+ sg_free_table(&pl022->sgt_rx);
+err_alloc_rx_sg:
+ return -ENOMEM;
+}
+
+static int __init pl022_dma_probe(struct pl022 *pl022)
+{
+ dma_cap_mask_t mask;
+
+ /* Try to acquire a generic DMA engine slave channel */
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+ /*
+ * We need both RX and TX channels to do DMA, else do none
+ * of them.
+ */
+ pl022->dma_rx_channel = dma_request_channel(mask,
+ pl022->master_info->dma_filter,
+ pl022->master_info->dma_rx_param);
+ if (!pl022->dma_rx_channel) {
+ dev_err(&pl022->adev->dev, "no RX DMA channel!\n");
+ goto err_no_rxchan;
+ }
+
+ pl022->dma_tx_channel = dma_request_channel(mask,
+ pl022->master_info->dma_filter,
+ pl022->master_info->dma_tx_param);
+ if (!pl022->dma_tx_channel) {
+ dev_err(&pl022->adev->dev, "no TX DMA channel!\n");
+ goto err_no_txchan;
+ }
+
+ pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL);
+ if (!pl022->dummypage) {
+ dev_err(&pl022->adev->dev, "no DMA dummypage!\n");
+ goto err_no_dummypage;
+ }
+
+ dev_info(&pl022->adev->dev, "setup for DMA on RX %s, TX %s\n",
+ dma_chan_name(pl022->dma_rx_channel),
+ dma_chan_name(pl022->dma_tx_channel));
+
+ return 0;
+
+err_no_dummypage:
+ dma_release_channel(pl022->dma_tx_channel);
+err_no_txchan:
+ dma_release_channel(pl022->dma_rx_channel);
+ pl022->dma_rx_channel = NULL;
+err_no_rxchan:
+ return -ENODEV;
+}
+
+static void terminate_dma(struct pl022 *pl022)
+{
+ struct dma_chan *rxchan = pl022->dma_rx_channel;
+ struct dma_chan *txchan = pl022->dma_tx_channel;
+
+ rxchan->device->device_control(rxchan, DMA_TERMINATE_ALL, 0);
+ txchan->device->device_control(txchan, DMA_TERMINATE_ALL, 0);
+ unmap_free_dma_scatter(pl022);
+}
+
+static void pl022_dma_remove(struct pl022 *pl022)
+{
+ if (pl022->busy)
+ terminate_dma(pl022);
+ if (pl022->dma_tx_channel)
+ dma_release_channel(pl022->dma_tx_channel);
+ if (pl022->dma_rx_channel)
+ dma_release_channel(pl022->dma_rx_channel);
+ kfree(pl022->dummypage);
+}
+
+#else
+static inline int configure_dma(struct pl022 *pl022)
+{
+ return -ENODEV;
+}
+
+static inline int pl022_dma_probe(struct pl022 *pl022)
+{
+ return 0;
+}
+
+static inline void pl022_dma_remove(struct pl022 *pl022)
+{
+}
+#endif
+
/**
* pl022_interrupt_handler - Interrupt handler for SSP controller
*
@@ -794,14 +1169,17 @@
if (unlikely(!irq_status))
return IRQ_NONE;
- /* This handles the error code interrupts */
+ /*
+ * This handles the FIFO interrupts, the timeout
+ * interrupts are flatly ignored, they cannot be
+ * trusted.
+ */
if (unlikely(irq_status & SSP_MIS_MASK_RORMIS)) {
/*
* Overrun interrupt - bail out since our Data has been
* corrupted
*/
- dev_err(&pl022->adev->dev,
- "FIFO overrun\n");
+ dev_err(&pl022->adev->dev, "FIFO overrun\n");
if (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RFF)
dev_err(&pl022->adev->dev,
"RXFIFO is full\n");
@@ -896,8 +1274,8 @@
}
/**
- * pump_transfers - Tasklet function which schedules next interrupt transfer
- * when running in interrupt transfer mode.
+ * pump_transfers - Tasklet function which schedules next transfer
+ * when running in interrupt or DMA transfer mode.
* @data: SSP driver private data structure
*
*/
@@ -954,65 +1332,23 @@
}
/* Flush the FIFOs and let's go! */
flush(pl022);
+
+ if (pl022->cur_chip->enable_dma) {
+ if (configure_dma(pl022)) {
+ dev_dbg(&pl022->adev->dev,
+ "configuration of DMA failed, fall back to interrupt mode\n");
+ goto err_config_dma;
+ }
+ return;
+ }
+
+err_config_dma:
writew(ENABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase));
}
-/**
- * NOT IMPLEMENTED
- * configure_dma - It configures the DMA pipes for DMA transfers
- * @data: SSP driver's private data structure
- *
- */
-static int configure_dma(void *data)
+static void do_interrupt_dma_transfer(struct pl022 *pl022)
{
- struct pl022 *pl022 = data;
- dev_dbg(&pl022->adev->dev, "configure DMA\n");
- return -ENOTSUPP;
-}
-
-/**
- * do_dma_transfer - It handles transfers of the current message
- * if it is DMA xfer.
- * NOT FULLY IMPLEMENTED
- * @data: SSP driver's private data structure
- */
-static void do_dma_transfer(void *data)
-{
- struct pl022 *pl022 = data;
-
- if (configure_dma(data)) {
- dev_dbg(&pl022->adev->dev, "configuration of DMA Failed!\n");
- goto err_config_dma;
- }
-
- /* TODO: Implememt DMA setup of pipes here */
-
- /* Enable target chip, set up transfer */
- pl022->cur_chip->cs_control(SSP_CHIP_SELECT);
- if (set_up_next_transfer(pl022, pl022->cur_transfer)) {
- /* Error path */
- pl022->cur_msg->state = STATE_ERROR;
- pl022->cur_msg->status = -EIO;
- giveback(pl022);
- return;
- }
- /* Enable SSP */
- writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE),
- SSP_CR1(pl022->virtbase));
-
- /* TODO: Enable the DMA transfer here */
- return;
-
- err_config_dma:
- pl022->cur_msg->state = STATE_ERROR;
- pl022->cur_msg->status = -EIO;
- giveback(pl022);
- return;
-}
-
-static void do_interrupt_transfer(void *data)
-{
- struct pl022 *pl022 = data;
+ u32 irqflags = ENABLE_ALL_INTERRUPTS;
/* Enable target chip */
pl022->cur_chip->cs_control(SSP_CHIP_SELECT);
@@ -1023,15 +1359,26 @@
giveback(pl022);
return;
}
+ /* If we're using DMA, set up DMA here */
+ if (pl022->cur_chip->enable_dma) {
+ /* Configure DMA transfer */
+ if (configure_dma(pl022)) {
+ dev_dbg(&pl022->adev->dev,
+ "configuration of DMA failed, fall back to interrupt mode\n");
+ goto err_config_dma;
+ }
+ /* Disable interrupts in DMA mode, IRQ from DMA controller */
+ irqflags = DISABLE_ALL_INTERRUPTS;
+ }
+err_config_dma:
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE),
SSP_CR1(pl022->virtbase));
- writew(ENABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase));
+ writew(irqflags, SSP_IMSC(pl022->virtbase));
}
-static void do_polling_transfer(void *data)
+static void do_polling_transfer(struct pl022 *pl022)
{
- struct pl022 *pl022 = data;
struct spi_message *message = NULL;
struct spi_transfer *transfer = NULL;
struct spi_transfer *previous = NULL;
@@ -1101,7 +1448,7 @@
*
* This function checks if there is any spi message in the queue that
* needs processing and delegate control to appropriate function
- * do_polling_transfer()/do_interrupt_transfer()/do_dma_transfer()
+ * do_polling_transfer()/do_interrupt_dma_transfer()
* based on the kind of the transfer
*
*/
@@ -1150,10 +1497,8 @@
if (pl022->cur_chip->xfer_type == POLLING_TRANSFER)
do_polling_transfer(pl022);
- else if (pl022->cur_chip->xfer_type == INTERRUPT_TRANSFER)
- do_interrupt_transfer(pl022);
else
- do_dma_transfer(pl022);
+ do_interrupt_dma_transfer(pl022);
}
@@ -1248,100 +1593,56 @@
}
static int verify_controller_parameters(struct pl022 *pl022,
- struct pl022_config_chip *chip_info)
+ struct pl022_config_chip const *chip_info)
{
- if ((chip_info->lbm != LOOPBACK_ENABLED)
- && (chip_info->lbm != LOOPBACK_DISABLED)) {
- dev_err(chip_info->dev,
- "loopback Mode is configured incorrectly\n");
- return -EINVAL;
- }
if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI)
|| (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"interface is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->iface == SSP_INTERFACE_UNIDIRECTIONAL) &&
(!pl022->vendor->unidir)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"unidirectional mode not supported in this "
"hardware version\n");
return -EINVAL;
}
if ((chip_info->hierarchy != SSP_MASTER)
&& (chip_info->hierarchy != SSP_SLAVE)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"hierarchy is configured incorrectly\n");
return -EINVAL;
}
- if (((chip_info->clk_freq).cpsdvsr < CPSDVR_MIN)
- || ((chip_info->clk_freq).cpsdvsr > CPSDVR_MAX)) {
- dev_err(chip_info->dev,
- "cpsdvsr is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->endian_rx != SSP_RX_MSB)
- && (chip_info->endian_rx != SSP_RX_LSB)) {
- dev_err(chip_info->dev,
- "RX FIFO endianess is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->endian_tx != SSP_TX_MSB)
- && (chip_info->endian_tx != SSP_TX_LSB)) {
- dev_err(chip_info->dev,
- "TX FIFO endianess is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->data_size < SSP_DATA_BITS_4)
- || (chip_info->data_size > SSP_DATA_BITS_32)) {
- dev_err(chip_info->dev,
- "DATA Size is configured incorrectly\n");
- return -EINVAL;
- }
if ((chip_info->com_mode != INTERRUPT_TRANSFER)
&& (chip_info->com_mode != DMA_TRANSFER)
&& (chip_info->com_mode != POLLING_TRANSFER)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Communication mode is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->rx_lev_trig < SSP_RX_1_OR_MORE_ELEM)
|| (chip_info->rx_lev_trig > SSP_RX_32_OR_MORE_ELEM)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"RX FIFO Trigger Level is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->tx_lev_trig < SSP_TX_1_OR_MORE_EMPTY_LOC)
|| (chip_info->tx_lev_trig > SSP_TX_32_OR_MORE_EMPTY_LOC)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"TX FIFO Trigger Level is configured incorrectly\n");
return -EINVAL;
}
- if (chip_info->iface == SSP_INTERFACE_MOTOROLA_SPI) {
- if ((chip_info->clk_phase != SSP_CLK_FIRST_EDGE)
- && (chip_info->clk_phase != SSP_CLK_SECOND_EDGE)) {
- dev_err(chip_info->dev,
- "Clock Phase is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->clk_pol != SSP_CLK_POL_IDLE_LOW)
- && (chip_info->clk_pol != SSP_CLK_POL_IDLE_HIGH)) {
- dev_err(chip_info->dev,
- "Clock Polarity is configured incorrectly\n");
- return -EINVAL;
- }
- }
if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) {
if ((chip_info->ctrl_len < SSP_BITS_4)
|| (chip_info->ctrl_len > SSP_BITS_32)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"CTRL LEN is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->wait_state != SSP_MWIRE_WAIT_ZERO)
&& (chip_info->wait_state != SSP_MWIRE_WAIT_ONE)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Wait State is configured incorrectly\n");
return -EINVAL;
}
@@ -1350,24 +1651,20 @@
if ((chip_info->duplex !=
SSP_MICROWIRE_CHANNEL_FULL_DUPLEX)
&& (chip_info->duplex !=
- SSP_MICROWIRE_CHANNEL_HALF_DUPLEX))
- dev_err(chip_info->dev,
+ SSP_MICROWIRE_CHANNEL_HALF_DUPLEX)) {
+ dev_err(&pl022->adev->dev,
"Microwire duplex mode is configured incorrectly\n");
return -EINVAL;
+ }
} else {
if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX)
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Microwire half duplex mode requested,"
" but this is only available in the"
" ST version of PL022\n");
return -EINVAL;
}
}
- if (chip_info->cs_control == NULL) {
- dev_warn(chip_info->dev,
- "Chip Select Function is NULL for this chip\n");
- chip_info->cs_control = null_cs_control;
- }
return 0;
}
@@ -1467,22 +1764,24 @@
return 0;
}
-/**
- * NOT IMPLEMENTED
- * process_dma_info - Processes the DMA info provided by client drivers
- * @chip_info: chip info provided by client device
- * @chip: Runtime state maintained by the SSP controller for each spi device
- *
- * This function processes and stores DMA config provided by client driver
- * into the runtime state maintained by the SSP controller driver
+
+/*
+ * A piece of default chip info unless the platform
+ * supplies it.
*/
-static int process_dma_info(struct pl022_config_chip *chip_info,
- struct chip_data *chip)
-{
- dev_err(chip_info->dev,
- "cannot process DMA info, DMA not implemented!\n");
- return -ENOTSUPP;
-}
+static const struct pl022_config_chip pl022_default_chip_info = {
+ .com_mode = POLLING_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ .hierarchy = SSP_SLAVE,
+ .slave_tx_disable = DO_NOT_DRIVE_TX,
+ .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
+ .ctrl_len = SSP_BITS_8,
+ .wait_state = SSP_MWIRE_WAIT_ZERO,
+ .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
+ .cs_control = null_cs_control,
+};
+
/**
* pl022_setup - setup function registered to SPI master framework
@@ -1496,23 +1795,15 @@
* controller hardware here, that is not done until the actual transfer
* commence.
*/
-
-/* FIXME: JUST GUESSING the spi->mode bits understood by this driver */
-#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
- | SPI_LSB_FIRST | SPI_LOOP)
-
static int pl022_setup(struct spi_device *spi)
{
- struct pl022_config_chip *chip_info;
+ struct pl022_config_chip const *chip_info;
struct chip_data *chip;
+ struct ssp_clock_params clk_freq;
int status = 0;
struct pl022 *pl022 = spi_master_get_devdata(spi->master);
-
- if (spi->mode & ~MODEBITS) {
- dev_dbg(&spi->dev, "unsupported mode bits %x\n",
- spi->mode & ~MODEBITS);
- return -EINVAL;
- }
+ unsigned int bits = spi->bits_per_word;
+ u32 tmp;
if (!spi->max_speed_hz)
return -EINVAL;
@@ -1535,48 +1826,13 @@
chip_info = spi->controller_data;
if (chip_info == NULL) {
+ chip_info = &pl022_default_chip_info;
/* spi_board_info.controller_data not is supplied */
dev_dbg(&spi->dev,
"using default controller_data settings\n");
-
- chip_info =
- kzalloc(sizeof(struct pl022_config_chip), GFP_KERNEL);
-
- if (!chip_info) {
- dev_err(&spi->dev,
- "cannot allocate controller data\n");
- status = -ENOMEM;
- goto err_first_setup;
- }
-
- dev_dbg(&spi->dev, "allocated memory for controller data\n");
-
- /* Pointer back to the SPI device */
- chip_info->dev = &spi->dev;
- /*
- * Set controller data default values:
- * Polling is supported by default
- */
- chip_info->lbm = LOOPBACK_DISABLED;
- chip_info->com_mode = POLLING_TRANSFER;
- chip_info->iface = SSP_INTERFACE_MOTOROLA_SPI;
- chip_info->hierarchy = SSP_SLAVE;
- chip_info->slave_tx_disable = DO_NOT_DRIVE_TX;
- chip_info->endian_tx = SSP_TX_LSB;
- chip_info->endian_rx = SSP_RX_LSB;
- chip_info->data_size = SSP_DATA_BITS_12;
- chip_info->rx_lev_trig = SSP_RX_1_OR_MORE_ELEM;
- chip_info->tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC;
- chip_info->clk_phase = SSP_CLK_SECOND_EDGE;
- chip_info->clk_pol = SSP_CLK_POL_IDLE_LOW;
- chip_info->ctrl_len = SSP_BITS_8;
- chip_info->wait_state = SSP_MWIRE_WAIT_ZERO;
- chip_info->duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX;
- chip_info->cs_control = null_cs_control;
- } else {
+ } else
dev_dbg(&spi->dev,
"using user supplied controller_data settings\n");
- }
/*
* We can override with custom divisors, else we use the board
@@ -1586,29 +1842,48 @@
&& (0 == chip_info->clk_freq.scr)) {
status = calculate_effective_freq(pl022,
spi->max_speed_hz,
- &chip_info->clk_freq);
+ &clk_freq);
if (status < 0)
goto err_config_params;
} else {
- if ((chip_info->clk_freq.cpsdvsr % 2) != 0)
- chip_info->clk_freq.cpsdvsr =
- chip_info->clk_freq.cpsdvsr - 1;
+ memcpy(&clk_freq, &chip_info->clk_freq, sizeof(clk_freq));
+ if ((clk_freq.cpsdvsr % 2) != 0)
+ clk_freq.cpsdvsr =
+ clk_freq.cpsdvsr - 1;
}
+ if ((clk_freq.cpsdvsr < CPSDVR_MIN)
+ || (clk_freq.cpsdvsr > CPSDVR_MAX)) {
+ dev_err(&spi->dev,
+ "cpsdvsr is configured incorrectly\n");
+ goto err_config_params;
+ }
+
+
status = verify_controller_parameters(pl022, chip_info);
if (status) {
dev_err(&spi->dev, "controller data is incorrect");
goto err_config_params;
}
+
/* Now set controller state based on controller data */
chip->xfer_type = chip_info->com_mode;
- chip->cs_control = chip_info->cs_control;
+ if (!chip_info->cs_control) {
+ chip->cs_control = null_cs_control;
+ dev_warn(&spi->dev,
+ "chip select function is NULL for this chip\n");
+ } else
+ chip->cs_control = chip_info->cs_control;
- if (chip_info->data_size <= 8) {
- dev_dbg(&spi->dev, "1 <= n <=8 bits per word\n");
+ if (bits <= 3) {
+ /* PL022 doesn't support less than 4-bits */
+ status = -ENOTSUPP;
+ goto err_config_params;
+ } else if (bits <= 8) {
+ dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n");
chip->n_bytes = 1;
chip->read = READING_U8;
chip->write = WRITING_U8;
- } else if (chip_info->data_size <= 16) {
+ } else if (bits <= 16) {
dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n");
chip->n_bytes = 2;
chip->read = READING_U16;
@@ -1625,6 +1900,7 @@
dev_err(&spi->dev,
"a standard pl022 can only handle "
"1 <= n <= 16 bit words\n");
+ status = -ENOTSUPP;
goto err_config_params;
}
}
@@ -1636,9 +1912,8 @@
chip->cpsr = 0;
if ((chip_info->com_mode == DMA_TRANSFER)
&& ((pl022->master_info)->enable_dma)) {
- chip->enable_dma = 1;
+ chip->enable_dma = true;
dev_dbg(&spi->dev, "DMA mode set in controller state\n");
- status = process_dma_info(chip_info, chip);
if (status < 0)
goto err_config_params;
SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED,
@@ -1646,7 +1921,7 @@
SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED,
SSP_DMACR_MASK_TXDMAE, 1);
} else {
- chip->enable_dma = 0;
+ chip->enable_dma = false;
dev_dbg(&spi->dev, "DMA mode NOT set in controller state\n");
SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED,
SSP_DMACR_MASK_RXDMAE, 0);
@@ -1654,10 +1929,12 @@
SSP_DMACR_MASK_TXDMAE, 1);
}
- chip->cpsr = chip_info->clk_freq.cpsdvsr;
+ chip->cpsr = clk_freq.cpsdvsr;
/* Special setup for the ST micro extended control registers */
if (pl022->vendor->extended_cr) {
+ u32 etx;
+
if (pl022->vendor->pl023) {
/* These bits are only in the PL023 */
SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay,
@@ -1673,29 +1950,51 @@
SSP_WRITE_BITS(chip->cr1, chip_info->wait_state,
SSP_CR1_MASK_MWAIT_ST, 6);
}
- SSP_WRITE_BITS(chip->cr0, chip_info->data_size,
+ SSP_WRITE_BITS(chip->cr0, bits - 1,
SSP_CR0_MASK_DSS_ST, 0);
- SSP_WRITE_BITS(chip->cr1, chip_info->endian_rx,
- SSP_CR1_MASK_RENDN_ST, 4);
- SSP_WRITE_BITS(chip->cr1, chip_info->endian_tx,
- SSP_CR1_MASK_TENDN_ST, 5);
+
+ if (spi->mode & SPI_LSB_FIRST) {
+ tmp = SSP_RX_LSB;
+ etx = SSP_TX_LSB;
+ } else {
+ tmp = SSP_RX_MSB;
+ etx = SSP_TX_MSB;
+ }
+ SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4);
+ SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5);
SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig,
SSP_CR1_MASK_RXIFLSEL_ST, 7);
SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig,
SSP_CR1_MASK_TXIFLSEL_ST, 10);
} else {
- SSP_WRITE_BITS(chip->cr0, chip_info->data_size,
+ SSP_WRITE_BITS(chip->cr0, bits - 1,
SSP_CR0_MASK_DSS, 0);
SSP_WRITE_BITS(chip->cr0, chip_info->iface,
SSP_CR0_MASK_FRF, 4);
}
+
/* Stuff that is common for all versions */
- SSP_WRITE_BITS(chip->cr0, chip_info->clk_pol, SSP_CR0_MASK_SPO, 6);
- SSP_WRITE_BITS(chip->cr0, chip_info->clk_phase, SSP_CR0_MASK_SPH, 7);
- SSP_WRITE_BITS(chip->cr0, chip_info->clk_freq.scr, SSP_CR0_MASK_SCR, 8);
+ if (spi->mode & SPI_CPOL)
+ tmp = SSP_CLK_POL_IDLE_HIGH;
+ else
+ tmp = SSP_CLK_POL_IDLE_LOW;
+ SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6);
+
+ if (spi->mode & SPI_CPHA)
+ tmp = SSP_CLK_SECOND_EDGE;
+ else
+ tmp = SSP_CLK_FIRST_EDGE;
+ SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 7);
+
+ SSP_WRITE_BITS(chip->cr0, clk_freq.scr, SSP_CR0_MASK_SCR, 8);
/* Loopback is available on all versions except PL023 */
- if (!pl022->vendor->pl023)
- SSP_WRITE_BITS(chip->cr1, chip_info->lbm, SSP_CR1_MASK_LBM, 0);
+ if (!pl022->vendor->pl023) {
+ if (spi->mode & SPI_LOOP)
+ tmp = LOOPBACK_ENABLED;
+ else
+ tmp = LOOPBACK_DISABLED;
+ SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0);
+ }
SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1);
SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2);
SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 3);
@@ -1704,7 +2003,7 @@
spi_set_ctldata(spi, chip);
return status;
err_config_params:
- err_first_setup:
+ spi_set_ctldata(spi, NULL);
kfree(chip);
return status;
}
@@ -1766,12 +2065,21 @@
master->setup = pl022_setup;
master->transfer = pl022_transfer;
+ /*
+ * Supports mode 0-3, loopback, and active low CS. Transfers are
+ * always MS bit first on the original pl022.
+ */
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
+ if (pl022->vendor->extended_cr)
+ master->mode_bits |= SPI_LSB_FIRST;
+
dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num);
status = amba_request_regions(adev, NULL);
if (status)
goto err_no_ioregion;
+ pl022->phybase = adev->res.start;
pl022->virtbase = ioremap(adev->res.start, resource_size(&adev->res));
if (pl022->virtbase == NULL) {
status = -ENOMEM;
@@ -1798,6 +2106,14 @@
dev_err(&adev->dev, "probe - cannot get IRQ (%d)\n", status);
goto err_no_irq;
}
+
+ /* Get DMA channels */
+ if (platform_info->enable_dma) {
+ status = pl022_dma_probe(pl022);
+ if (status != 0)
+ goto err_no_dma;
+ }
+
/* Initialize and start queue */
status = init_queue(pl022);
if (status != 0) {
@@ -1826,6 +2142,8 @@
err_start_queue:
err_init_queue:
destroy_queue(pl022);
+ pl022_dma_remove(pl022);
+ err_no_dma:
free_irq(adev->irq[0], pl022);
err_no_irq:
clk_put(pl022->clk);
@@ -1856,6 +2174,7 @@
return status;
}
load_ssp_default_config(pl022);
+ pl022_dma_remove(pl022);
free_irq(adev->irq[0], pl022);
clk_disable(pl022->clk);
clk_put(pl022->clk);
diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index b3a94ca..d703927 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -489,10 +489,8 @@
dev_err(&spi->dev, "TXS timed out\n");
goto out;
}
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "write-%d %02x\n",
+ dev_vdbg(&spi->dev, "write-%d %02x\n",
word_len, *tx);
-#endif
__raw_writel(*tx++, tx_reg);
}
if (rx != NULL) {
@@ -506,10 +504,8 @@
(l & OMAP2_MCSPI_CHCONF_TURBO)) {
omap2_mcspi_set_enable(spi, 0);
*rx++ = __raw_readl(rx_reg);
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "read-%d %02x\n",
+ dev_vdbg(&spi->dev, "read-%d %02x\n",
word_len, *(rx - 1));
-#endif
if (mcspi_wait_for_reg_bit(chstat_reg,
OMAP2_MCSPI_CHSTAT_RXS) < 0) {
dev_err(&spi->dev,
@@ -522,10 +518,8 @@
}
*rx++ = __raw_readl(rx_reg);
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "read-%d %02x\n",
+ dev_vdbg(&spi->dev, "read-%d %02x\n",
word_len, *(rx - 1));
-#endif
}
} while (c);
} else if (word_len <= 16) {
@@ -542,10 +536,8 @@
dev_err(&spi->dev, "TXS timed out\n");
goto out;
}
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "write-%d %04x\n",
+ dev_vdbg(&spi->dev, "write-%d %04x\n",
word_len, *tx);
-#endif
__raw_writel(*tx++, tx_reg);
}
if (rx != NULL) {
@@ -559,10 +551,8 @@
(l & OMAP2_MCSPI_CHCONF_TURBO)) {
omap2_mcspi_set_enable(spi, 0);
*rx++ = __raw_readl(rx_reg);
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "read-%d %04x\n",
+ dev_vdbg(&spi->dev, "read-%d %04x\n",
word_len, *(rx - 1));
-#endif
if (mcspi_wait_for_reg_bit(chstat_reg,
OMAP2_MCSPI_CHSTAT_RXS) < 0) {
dev_err(&spi->dev,
@@ -575,10 +565,8 @@
}
*rx++ = __raw_readl(rx_reg);
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "read-%d %04x\n",
+ dev_vdbg(&spi->dev, "read-%d %04x\n",
word_len, *(rx - 1));
-#endif
}
} while (c);
} else if (word_len <= 32) {
@@ -595,10 +583,8 @@
dev_err(&spi->dev, "TXS timed out\n");
goto out;
}
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "write-%d %08x\n",
+ dev_vdbg(&spi->dev, "write-%d %08x\n",
word_len, *tx);
-#endif
__raw_writel(*tx++, tx_reg);
}
if (rx != NULL) {
@@ -612,10 +598,8 @@
(l & OMAP2_MCSPI_CHCONF_TURBO)) {
omap2_mcspi_set_enable(spi, 0);
*rx++ = __raw_readl(rx_reg);
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "read-%d %08x\n",
+ dev_vdbg(&spi->dev, "read-%d %08x\n",
word_len, *(rx - 1));
-#endif
if (mcspi_wait_for_reg_bit(chstat_reg,
OMAP2_MCSPI_CHSTAT_RXS) < 0) {
dev_err(&spi->dev,
@@ -628,10 +612,8 @@
}
*rx++ = __raw_readl(rx_reg);
-#ifdef VERBOSE
- dev_dbg(&spi->dev, "read-%d %08x\n",
+ dev_vdbg(&spi->dev, "read-%d %08x\n",
word_len, *(rx - 1));
-#endif
}
} while (c);
}
diff --git a/drivers/spi/orion_spi.c b/drivers/spi/orion_spi.c
index 3aea50d..0b677dc 100644
--- a/drivers/spi/orion_spi.c
+++ b/drivers/spi/orion_spi.c
@@ -404,7 +404,7 @@
goto msg_rejected;
}
- if ((t != NULL) && t->bits_per_word)
+ if (t->bits_per_word)
bits_per_word = t->bits_per_word;
if ((bits_per_word != 8) && (bits_per_word != 16)) {
@@ -415,7 +415,7 @@
goto msg_rejected;
}
/*make sure buffer length is even when working in 16 bit mode*/
- if ((t != NULL) && (t->bits_per_word == 16) && (t->len & 1)) {
+ if ((t->bits_per_word == 16) && (t->len & 1)) {
dev_err(&spi->dev,
"message rejected : "
"odd data length (%d) while in 16 bit mode\n",
diff --git a/drivers/spi/spi_s3c64xx.c b/drivers/spi/spi_s3c64xx.c
index c3038da..795828b 100644
--- a/drivers/spi/spi_s3c64xx.c
+++ b/drivers/spi/spi_s3c64xx.c
@@ -261,15 +261,25 @@
chcfg |= S3C64XX_SPI_CH_TXCH_ON;
if (dma_mode) {
modecfg |= S3C64XX_SPI_MODE_TXDMA_ON;
- s3c2410_dma_config(sdd->tx_dmach, 1);
+ s3c2410_dma_config(sdd->tx_dmach, sdd->cur_bpw / 8);
s3c2410_dma_enqueue(sdd->tx_dmach, (void *)sdd,
xfer->tx_dma, xfer->len);
s3c2410_dma_ctrl(sdd->tx_dmach, S3C2410_DMAOP_START);
} else {
- unsigned char *buf = (unsigned char *) xfer->tx_buf;
- int i = 0;
- while (i < xfer->len)
- writeb(buf[i++], regs + S3C64XX_SPI_TX_DATA);
+ switch (sdd->cur_bpw) {
+ case 32:
+ iowrite32_rep(regs + S3C64XX_SPI_TX_DATA,
+ xfer->tx_buf, xfer->len / 4);
+ break;
+ case 16:
+ iowrite16_rep(regs + S3C64XX_SPI_TX_DATA,
+ xfer->tx_buf, xfer->len / 2);
+ break;
+ default:
+ iowrite8_rep(regs + S3C64XX_SPI_TX_DATA,
+ xfer->tx_buf, xfer->len);
+ break;
+ }
}
}
@@ -286,7 +296,7 @@
writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
| S3C64XX_SPI_PACKET_CNT_EN,
regs + S3C64XX_SPI_PACKET_CNT);
- s3c2410_dma_config(sdd->rx_dmach, 1);
+ s3c2410_dma_config(sdd->rx_dmach, sdd->cur_bpw / 8);
s3c2410_dma_enqueue(sdd->rx_dmach, (void *)sdd,
xfer->rx_dma, xfer->len);
s3c2410_dma_ctrl(sdd->rx_dmach, S3C2410_DMAOP_START);
@@ -366,20 +376,26 @@
return -EIO;
}
} else {
- unsigned char *buf;
- int i;
-
/* If it was only Tx */
if (xfer->rx_buf == NULL) {
sdd->state &= ~TXBUSY;
return 0;
}
- i = 0;
- buf = xfer->rx_buf;
- while (i < xfer->len)
- buf[i++] = readb(regs + S3C64XX_SPI_RX_DATA);
-
+ switch (sdd->cur_bpw) {
+ case 32:
+ ioread32_rep(regs + S3C64XX_SPI_RX_DATA,
+ xfer->rx_buf, xfer->len / 4);
+ break;
+ case 16:
+ ioread16_rep(regs + S3C64XX_SPI_RX_DATA,
+ xfer->rx_buf, xfer->len / 2);
+ break;
+ default:
+ ioread8_rep(regs + S3C64XX_SPI_RX_DATA,
+ xfer->rx_buf, xfer->len);
+ break;
+ }
sdd->state &= ~RXBUSY;
}
@@ -399,13 +415,18 @@
static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
{
+ struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
void __iomem *regs = sdd->regs;
u32 val;
/* Disable Clock */
- val = readl(regs + S3C64XX_SPI_CLK_CFG);
- val &= ~S3C64XX_SPI_ENCLK_ENABLE;
- writel(val, regs + S3C64XX_SPI_CLK_CFG);
+ if (sci->clk_from_cmu) {
+ clk_disable(sdd->src_clk);
+ } else {
+ val = readl(regs + S3C64XX_SPI_CLK_CFG);
+ val &= ~S3C64XX_SPI_ENCLK_ENABLE;
+ writel(val, regs + S3C64XX_SPI_CLK_CFG);
+ }
/* Set Polarity and Phase */
val = readl(regs + S3C64XX_SPI_CH_CFG);
@@ -429,29 +450,39 @@
switch (sdd->cur_bpw) {
case 32:
val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
+ val |= S3C64XX_SPI_MODE_CH_TSZ_WORD;
break;
case 16:
val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
+ val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD;
break;
default:
val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
+ val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE;
break;
}
- val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; /* Always 8bits wide */
writel(val, regs + S3C64XX_SPI_MODE_CFG);
- /* Configure Clock */
- val = readl(regs + S3C64XX_SPI_CLK_CFG);
- val &= ~S3C64XX_SPI_PSR_MASK;
- val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1)
- & S3C64XX_SPI_PSR_MASK);
- writel(val, regs + S3C64XX_SPI_CLK_CFG);
+ if (sci->clk_from_cmu) {
+ /* Configure Clock */
+ /* There is half-multiplier before the SPI */
+ clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
+ /* Enable Clock */
+ clk_enable(sdd->src_clk);
+ } else {
+ /* Configure Clock */
+ val = readl(regs + S3C64XX_SPI_CLK_CFG);
+ val &= ~S3C64XX_SPI_PSR_MASK;
+ val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1)
+ & S3C64XX_SPI_PSR_MASK);
+ writel(val, regs + S3C64XX_SPI_CLK_CFG);
- /* Enable Clock */
- val = readl(regs + S3C64XX_SPI_CLK_CFG);
- val |= S3C64XX_SPI_ENCLK_ENABLE;
- writel(val, regs + S3C64XX_SPI_CLK_CFG);
+ /* Enable Clock */
+ val = readl(regs + S3C64XX_SPI_CLK_CFG);
+ val |= S3C64XX_SPI_ENCLK_ENABLE;
+ writel(val, regs + S3C64XX_SPI_CLK_CFG);
+ }
}
static void s3c64xx_spi_dma_rxcb(struct s3c2410_dma_chan *chan, void *buf_id,
@@ -499,6 +530,7 @@
static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
struct spi_message *msg)
{
+ struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
struct device *dev = &sdd->pdev->dev;
struct spi_transfer *xfer;
@@ -514,6 +546,9 @@
/* Map until end or first fail */
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+ if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+ continue;
+
if (xfer->tx_buf != NULL) {
xfer->tx_dma = dma_map_single(dev,
(void *)xfer->tx_buf, xfer->len,
@@ -545,6 +580,7 @@
static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
struct spi_message *msg)
{
+ struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
struct device *dev = &sdd->pdev->dev;
struct spi_transfer *xfer;
@@ -553,6 +589,9 @@
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+ if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+ continue;
+
if (xfer->rx_buf != NULL
&& xfer->rx_dma != XFER_DMAADDR_INVALID)
dma_unmap_single(dev, xfer->rx_dma,
@@ -608,6 +647,14 @@
bpw = xfer->bits_per_word ? : spi->bits_per_word;
speed = xfer->speed_hz ? : spi->max_speed_hz;
+ if (xfer->len % (bpw / 8)) {
+ dev_err(&spi->dev,
+ "Xfer length(%u) not a multiple of word size(%u)\n",
+ xfer->len, bpw / 8);
+ status = -EIO;
+ goto out;
+ }
+
if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) {
sdd->cur_bpw = bpw;
sdd->cur_speed = speed;
@@ -798,7 +845,6 @@
struct s3c64xx_spi_driver_data *sdd;
struct s3c64xx_spi_info *sci;
struct spi_message *msg;
- u32 psr, speed;
unsigned long flags;
int err = 0;
@@ -841,31 +887,36 @@
}
/* Check if we can provide the requested rate */
- speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1); /* Max possible */
+ if (!sci->clk_from_cmu) {
+ u32 psr, speed;
- if (spi->max_speed_hz > speed)
- spi->max_speed_hz = speed;
+ /* Max possible */
+ speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1);
- psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1;
- psr &= S3C64XX_SPI_PSR_MASK;
- if (psr == S3C64XX_SPI_PSR_MASK)
- psr--;
+ if (spi->max_speed_hz > speed)
+ spi->max_speed_hz = speed;
- speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
- if (spi->max_speed_hz < speed) {
- if (psr+1 < S3C64XX_SPI_PSR_MASK) {
- psr++;
- } else {
- err = -EINVAL;
- goto setup_exit;
+ psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1;
+ psr &= S3C64XX_SPI_PSR_MASK;
+ if (psr == S3C64XX_SPI_PSR_MASK)
+ psr--;
+
+ speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
+ if (spi->max_speed_hz < speed) {
+ if (psr+1 < S3C64XX_SPI_PSR_MASK) {
+ psr++;
+ } else {
+ err = -EINVAL;
+ goto setup_exit;
+ }
}
- }
- speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
- if (spi->max_speed_hz >= speed)
- spi->max_speed_hz = speed;
- else
- err = -EINVAL;
+ speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
+ if (spi->max_speed_hz >= speed)
+ spi->max_speed_hz = speed;
+ else
+ err = -EINVAL;
+ }
setup_exit:
@@ -888,7 +939,8 @@
/* Disable Interrupts - we use Polling if not DMA mode */
writel(0, regs + S3C64XX_SPI_INT_EN);
- writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
+ if (!sci->clk_from_cmu)
+ writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
regs + S3C64XX_SPI_CLK_CFG);
writel(0, regs + S3C64XX_SPI_MODE_CFG);
writel(0, regs + S3C64XX_SPI_PACKET_CNT);
diff --git a/drivers/spi/spi_topcliff_pch.c b/drivers/spi/spi_topcliff_pch.c
new file mode 100644
index 0000000..9774623
--- /dev/null
+++ b/drivers/spi/spi_topcliff_pch.c
@@ -0,0 +1,1303 @@
+/*
+ * SPI bus driver for the Topcliff PCH used by Intel SoCs
+ *
+ * Copyright (C) 2010 OKI SEMICONDUCTOR Co., LTD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/wait.h>
+#include <linux/spi/spi.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/spi/spidev.h>
+#include <linux/module.h>
+#include <linux/device.h>
+
+/* Register offsets */
+#define PCH_SPCR 0x00 /* SPI control register */
+#define PCH_SPBRR 0x04 /* SPI baud rate register */
+#define PCH_SPSR 0x08 /* SPI status register */
+#define PCH_SPDWR 0x0C /* SPI write data register */
+#define PCH_SPDRR 0x10 /* SPI read data register */
+#define PCH_SSNXCR 0x18 /* SSN Expand Control Register */
+#define PCH_SRST 0x1C /* SPI reset register */
+
+#define PCH_SPSR_TFD 0x000007C0
+#define PCH_SPSR_RFD 0x0000F800
+
+#define PCH_READABLE(x) (((x) & PCH_SPSR_RFD)>>11)
+#define PCH_WRITABLE(x) (((x) & PCH_SPSR_TFD)>>6)
+
+#define PCH_RX_THOLD 7
+#define PCH_RX_THOLD_MAX 15
+
+#define PCH_MAX_BAUDRATE 5000000
+#define PCH_MAX_FIFO_DEPTH 16
+
+#define STATUS_RUNNING 1
+#define STATUS_EXITING 2
+#define PCH_SLEEP_TIME 10
+
+#define PCH_ADDRESS_SIZE 0x20
+
+#define SSN_LOW 0x02U
+#define SSN_NO_CONTROL 0x00U
+#define PCH_MAX_CS 0xFF
+#define PCI_DEVICE_ID_GE_SPI 0x8816
+
+#define SPCR_SPE_BIT (1 << 0)
+#define SPCR_MSTR_BIT (1 << 1)
+#define SPCR_LSBF_BIT (1 << 4)
+#define SPCR_CPHA_BIT (1 << 5)
+#define SPCR_CPOL_BIT (1 << 6)
+#define SPCR_TFIE_BIT (1 << 8)
+#define SPCR_RFIE_BIT (1 << 9)
+#define SPCR_FIE_BIT (1 << 10)
+#define SPCR_ORIE_BIT (1 << 11)
+#define SPCR_MDFIE_BIT (1 << 12)
+#define SPCR_FICLR_BIT (1 << 24)
+#define SPSR_TFI_BIT (1 << 0)
+#define SPSR_RFI_BIT (1 << 1)
+#define SPSR_FI_BIT (1 << 2)
+#define SPBRR_SIZE_BIT (1 << 10)
+
+#define PCH_ALL (SPCR_TFIE_BIT|SPCR_RFIE_BIT|SPCR_FIE_BIT|SPCR_ORIE_BIT|SPCR_MDFIE_BIT)
+
+#define SPCR_RFIC_FIELD 20
+#define SPCR_TFIC_FIELD 16
+
+#define SPSR_INT_BITS 0x1F
+#define MASK_SPBRR_SPBR_BITS (~((1 << 10) - 1))
+#define MASK_RFIC_SPCR_BITS (~(0xf << 20))
+#define MASK_TFIC_SPCR_BITS (~(0xf000f << 12))
+
+#define PCH_CLOCK_HZ 50000000
+#define PCH_MAX_SPBR 1023
+
+
+/**
+ * struct pch_spi_data - Holds the SPI channel specific details
+ * @io_remap_addr: The remapped PCI base address
+ * @master: Pointer to the SPI master structure
+ * @work: Reference to work queue handler
+ * @wk: Workqueue for carrying out execution of the
+ * requests
+ * @wait: Wait queue for waking up upon receiving an
+ * interrupt.
+ * @transfer_complete: Status of SPI Transfer
+ * @bcurrent_msg_processing: Status flag for message processing
+ * @lock: Lock for protecting this structure
+ * @queue: SPI Message queue
+ * @status: Status of the SPI driver
+ * @bpw_len: Length of data to be transferred in bits per
+ * word
+ * @transfer_active: Flag showing active transfer
+ * @tx_index: Transmit data count; for bookkeeping during
+ * transfer
+ * @rx_index: Receive data count; for bookkeeping during
+ * transfer
+ * @tx_buff: Buffer for data to be transmitted
+ * @rx_index: Buffer for Received data
+ * @n_curnt_chip: The chip number that this SPI driver currently
+ * operates on
+ * @current_chip: Reference to the current chip that this SPI
+ * driver currently operates on
+ * @current_msg: The current message that this SPI driver is
+ * handling
+ * @cur_trans: The current transfer that this SPI driver is
+ * handling
+ * @board_dat: Reference to the SPI device data structure
+ */
+struct pch_spi_data {
+ void __iomem *io_remap_addr;
+ struct spi_master *master;
+ struct work_struct work;
+ struct workqueue_struct *wk;
+ wait_queue_head_t wait;
+ u8 transfer_complete;
+ u8 bcurrent_msg_processing;
+ spinlock_t lock;
+ struct list_head queue;
+ u8 status;
+ u32 bpw_len;
+ u8 transfer_active;
+ u32 tx_index;
+ u32 rx_index;
+ u16 *pkt_tx_buff;
+ u16 *pkt_rx_buff;
+ u8 n_curnt_chip;
+ struct spi_device *current_chip;
+ struct spi_message *current_msg;
+ struct spi_transfer *cur_trans;
+ struct pch_spi_board_data *board_dat;
+};
+
+/**
+ * struct pch_spi_board_data - Holds the SPI device specific details
+ * @pdev: Pointer to the PCI device
+ * @irq_reg_sts: Status of IRQ registration
+ * @pci_req_sts: Status of pci_request_regions
+ * @suspend_sts: Status of suspend
+ * @data: Pointer to SPI channel data structure
+ */
+struct pch_spi_board_data {
+ struct pci_dev *pdev;
+ u8 irq_reg_sts;
+ u8 pci_req_sts;
+ u8 suspend_sts;
+ struct pch_spi_data *data;
+};
+
+static struct pci_device_id pch_spi_pcidev_id[] = {
+ {PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_GE_SPI)},
+ {0,}
+};
+
+/**
+ * pch_spi_writereg() - Performs register writes
+ * @master: Pointer to struct spi_master.
+ * @idx: Register offset.
+ * @val: Value to be written to register.
+ */
+static inline void pch_spi_writereg(struct spi_master *master, int idx, u32 val)
+{
+ struct pch_spi_data *data = spi_master_get_devdata(master);
+ iowrite32(val, (data->io_remap_addr + idx));
+}
+
+/**
+ * pch_spi_readreg() - Performs register reads
+ * @master: Pointer to struct spi_master.
+ * @idx: Register offset.
+ */
+static inline u32 pch_spi_readreg(struct spi_master *master, int idx)
+{
+ struct pch_spi_data *data = spi_master_get_devdata(master);
+ return ioread32(data->io_remap_addr + idx);
+}
+
+static inline void pch_spi_setclr_reg(struct spi_master *master, int idx,
+ u32 set, u32 clr)
+{
+ u32 tmp = pch_spi_readreg(master, idx);
+ tmp = (tmp & ~clr) | set;
+ pch_spi_writereg(master, idx, tmp);
+}
+
+static void pch_spi_set_master_mode(struct spi_master *master)
+{
+ pch_spi_setclr_reg(master, PCH_SPCR, SPCR_MSTR_BIT, 0);
+}
+
+/**
+ * pch_spi_clear_fifo() - Clears the Transmit and Receive FIFOs
+ * @master: Pointer to struct spi_master.
+ */
+static void pch_spi_clear_fifo(struct spi_master *master)
+{
+ pch_spi_setclr_reg(master, PCH_SPCR, SPCR_FICLR_BIT, 0);
+ pch_spi_setclr_reg(master, PCH_SPCR, 0, SPCR_FICLR_BIT);
+}
+
+static void pch_spi_handler_sub(struct pch_spi_data *data, u32 reg_spsr_val,
+ void __iomem *io_remap_addr)
+{
+ u32 n_read, tx_index, rx_index, bpw_len;
+ u16 *pkt_rx_buffer, *pkt_tx_buff;
+ int read_cnt;
+ u32 reg_spcr_val;
+ void __iomem *spsr;
+ void __iomem *spdrr;
+ void __iomem *spdwr;
+
+ spsr = io_remap_addr + PCH_SPSR;
+ iowrite32(reg_spsr_val, spsr);
+
+ if (data->transfer_active) {
+ rx_index = data->rx_index;
+ tx_index = data->tx_index;
+ bpw_len = data->bpw_len;
+ pkt_rx_buffer = data->pkt_rx_buff;
+ pkt_tx_buff = data->pkt_tx_buff;
+
+ spdrr = io_remap_addr + PCH_SPDRR;
+ spdwr = io_remap_addr + PCH_SPDWR;
+
+ n_read = PCH_READABLE(reg_spsr_val);
+
+ for (read_cnt = 0; (read_cnt < n_read); read_cnt++) {
+ pkt_rx_buffer[rx_index++] = ioread32(spdrr);
+ if (tx_index < bpw_len)
+ iowrite32(pkt_tx_buff[tx_index++], spdwr);
+ }
+
+ /* disable RFI if not needed */
+ if ((bpw_len - rx_index) <= PCH_MAX_FIFO_DEPTH) {
+ reg_spcr_val = ioread32(io_remap_addr + PCH_SPCR);
+ reg_spcr_val &= ~SPCR_RFIE_BIT; /* disable RFI */
+
+ /* reset rx threshold */
+ reg_spcr_val &= MASK_RFIC_SPCR_BITS;
+ reg_spcr_val |= (PCH_RX_THOLD_MAX << SPCR_RFIC_FIELD);
+ iowrite32(((reg_spcr_val) &= (~(SPCR_RFIE_BIT))),
+ (io_remap_addr + PCH_SPCR));
+ }
+
+ /* update counts */
+ data->tx_index = tx_index;
+ data->rx_index = rx_index;
+
+ }
+
+ /* if transfer complete interrupt */
+ if (reg_spsr_val & SPSR_FI_BIT) {
+ /* disable FI & RFI interrupts */
+ pch_spi_setclr_reg(data->master, PCH_SPCR, 0,
+ SPCR_FIE_BIT | SPCR_TFIE_BIT);
+
+ /* transfer is completed;inform pch_spi_process_messages */
+ data->transfer_complete = true;
+ wake_up(&data->wait);
+ }
+}
+
+/**
+ * pch_spi_handler() - Interrupt handler
+ * @irq: The interrupt number.
+ * @dev_id: Pointer to struct pch_spi_board_data.
+ */
+static irqreturn_t pch_spi_handler(int irq, void *dev_id)
+{
+ u32 reg_spsr_val;
+ struct pch_spi_data *data;
+ void __iomem *spsr;
+ void __iomem *io_remap_addr;
+ irqreturn_t ret = IRQ_NONE;
+ struct pch_spi_board_data *board_dat = dev_id;
+
+ if (board_dat->suspend_sts) {
+ dev_dbg(&board_dat->pdev->dev,
+ "%s returning due to suspend\n", __func__);
+ return IRQ_NONE;
+ }
+
+ data = board_dat->data;
+ io_remap_addr = data->io_remap_addr;
+ spsr = io_remap_addr + PCH_SPSR;
+
+ reg_spsr_val = ioread32(spsr);
+
+ /* Check if the interrupt is for SPI device */
+ if (reg_spsr_val & (SPSR_FI_BIT | SPSR_RFI_BIT)) {
+ pch_spi_handler_sub(data, reg_spsr_val, io_remap_addr);
+ ret = IRQ_HANDLED;
+ }
+
+ dev_dbg(&board_dat->pdev->dev, "%s EXIT return value=%d\n",
+ __func__, ret);
+
+ return ret;
+}
+
+/**
+ * pch_spi_set_baud_rate() - Sets SPBR field in SPBRR
+ * @master: Pointer to struct spi_master.
+ * @speed_hz: Baud rate.
+ */
+static void pch_spi_set_baud_rate(struct spi_master *master, u32 speed_hz)
+{
+ u32 n_spbr = PCH_CLOCK_HZ / (speed_hz * 2);
+
+ /* if baud rate is less than we can support limit it */
+ if (n_spbr > PCH_MAX_SPBR)
+ n_spbr = PCH_MAX_SPBR;
+
+ pch_spi_setclr_reg(master, PCH_SPBRR, n_spbr, ~MASK_SPBRR_SPBR_BITS);
+}
+
+/**
+ * pch_spi_set_bits_per_word() - Sets SIZE field in SPBRR
+ * @master: Pointer to struct spi_master.
+ * @bits_per_word: Bits per word for SPI transfer.
+ */
+static void pch_spi_set_bits_per_word(struct spi_master *master,
+ u8 bits_per_word)
+{
+ if (bits_per_word == 8)
+ pch_spi_setclr_reg(master, PCH_SPBRR, 0, SPBRR_SIZE_BIT);
+ else
+ pch_spi_setclr_reg(master, PCH_SPBRR, SPBRR_SIZE_BIT, 0);
+}
+
+/**
+ * pch_spi_setup_transfer() - Configures the PCH SPI hardware for transfer
+ * @spi: Pointer to struct spi_device.
+ */
+static void pch_spi_setup_transfer(struct spi_device *spi)
+{
+ u32 flags = 0;
+
+ dev_dbg(&spi->dev, "%s SPBRR content =%x setting baud rate=%d\n",
+ __func__, pch_spi_readreg(spi->master, PCH_SPBRR),
+ spi->max_speed_hz);
+ pch_spi_set_baud_rate(spi->master, spi->max_speed_hz);
+
+ /* set bits per word */
+ pch_spi_set_bits_per_word(spi->master, spi->bits_per_word);
+
+ if (!(spi->mode & SPI_LSB_FIRST))
+ flags |= SPCR_LSBF_BIT;
+ if (spi->mode & SPI_CPOL)
+ flags |= SPCR_CPOL_BIT;
+ if (spi->mode & SPI_CPHA)
+ flags |= SPCR_CPHA_BIT;
+ pch_spi_setclr_reg(spi->master, PCH_SPCR, flags,
+ (SPCR_LSBF_BIT | SPCR_CPOL_BIT | SPCR_CPHA_BIT));
+
+ /* Clear the FIFO by toggling FICLR to 1 and back to 0 */
+ pch_spi_clear_fifo(spi->master);
+}
+
+/**
+ * pch_spi_reset() - Clears SPI registers
+ * @master: Pointer to struct spi_master.
+ */
+static void pch_spi_reset(struct spi_master *master)
+{
+ /* write 1 to reset SPI */
+ pch_spi_writereg(master, PCH_SRST, 0x1);
+
+ /* clear reset */
+ pch_spi_writereg(master, PCH_SRST, 0x0);
+}
+
+static int pch_spi_setup(struct spi_device *pspi)
+{
+ /* check bits per word */
+ if (pspi->bits_per_word == 0) {
+ pspi->bits_per_word = 8;
+ dev_dbg(&pspi->dev, "%s 8 bits per word\n", __func__);
+ }
+
+ if ((pspi->bits_per_word != 8) && (pspi->bits_per_word != 16)) {
+ dev_err(&pspi->dev, "%s Invalid bits per word\n", __func__);
+ return -EINVAL;
+ }
+
+ /* Check baud rate setting */
+ /* if baud rate of chip is greater than
+ max we can support,return error */
+ if ((pspi->max_speed_hz) > PCH_MAX_BAUDRATE)
+ pspi->max_speed_hz = PCH_MAX_BAUDRATE;
+
+ dev_dbg(&pspi->dev, "%s MODE = %x\n", __func__,
+ (pspi->mode) & (SPI_CPOL | SPI_CPHA));
+
+ return 0;
+}
+
+static int pch_spi_transfer(struct spi_device *pspi, struct spi_message *pmsg)
+{
+
+ struct spi_transfer *transfer;
+ struct pch_spi_data *data = spi_master_get_devdata(pspi->master);
+ int retval;
+ unsigned long flags;
+
+ /* validate spi message and baud rate */
+ if (unlikely(list_empty(&pmsg->transfers) == 1)) {
+ dev_err(&pspi->dev, "%s list empty\n", __func__);
+ retval = -EINVAL;
+ goto err_out;
+ }
+
+ if (unlikely(pspi->max_speed_hz == 0)) {
+ dev_err(&pspi->dev, "%s pch_spi_tranfer maxspeed=%d\n",
+ __func__, pspi->max_speed_hz);
+ retval = -EINVAL;
+ goto err_out;
+ }
+
+ dev_dbg(&pspi->dev, "%s Transfer List not empty. "
+ "Transfer Speed is set.\n", __func__);
+
+ /* validate Tx/Rx buffers and Transfer length */
+ list_for_each_entry(transfer, &pmsg->transfers, transfer_list) {
+ if (!transfer->tx_buf && !transfer->rx_buf) {
+ dev_err(&pspi->dev,
+ "%s Tx and Rx buffer NULL\n", __func__);
+ retval = -EINVAL;
+ goto err_out;
+ }
+
+ if (!transfer->len) {
+ dev_err(&pspi->dev, "%s Transfer length invalid\n",
+ __func__);
+ retval = -EINVAL;
+ goto err_out;
+ }
+
+ dev_dbg(&pspi->dev, "%s Tx/Rx buffer valid. Transfer length"
+ " valid\n", __func__);
+
+ /* if baud rate hs been specified validate the same */
+ if (transfer->speed_hz > PCH_MAX_BAUDRATE)
+ transfer->speed_hz = PCH_MAX_BAUDRATE;
+
+ /* if bits per word has been specified validate the same */
+ if (transfer->bits_per_word) {
+ if ((transfer->bits_per_word != 8)
+ && (transfer->bits_per_word != 16)) {
+ retval = -EINVAL;
+ dev_err(&pspi->dev,
+ "%s Invalid bits per word\n", __func__);
+ goto err_out;
+ }
+ }
+ }
+
+ spin_lock_irqsave(&data->lock, flags);
+
+ /* We won't process any messages if we have been asked to terminate */
+ if (data->status == STATUS_EXITING) {
+ dev_err(&pspi->dev, "%s status = STATUS_EXITING.\n", __func__);
+ retval = -ESHUTDOWN;
+ goto err_return_spinlock;
+ }
+
+ /* If suspended ,return -EINVAL */
+ if (data->board_dat->suspend_sts) {
+ dev_err(&pspi->dev, "%s suspend; returning EINVAL\n", __func__);
+ retval = -EINVAL;
+ goto err_return_spinlock;
+ }
+
+ /* set status of message */
+ pmsg->actual_length = 0;
+ dev_dbg(&pspi->dev, "%s - pmsg->status =%d\n", __func__, pmsg->status);
+
+ pmsg->status = -EINPROGRESS;
+
+ /* add message to queue */
+ list_add_tail(&pmsg->queue, &data->queue);
+ dev_dbg(&pspi->dev, "%s - Invoked list_add_tail\n", __func__);
+
+ /* schedule work queue to run */
+ queue_work(data->wk, &data->work);
+ dev_dbg(&pspi->dev, "%s - Invoked queue work\n", __func__);
+
+ retval = 0;
+
+err_return_spinlock:
+ spin_unlock_irqrestore(&data->lock, flags);
+err_out:
+ dev_dbg(&pspi->dev, "%s RETURN=%d\n", __func__, retval);
+ return retval;
+}
+
+static inline void pch_spi_select_chip(struct pch_spi_data *data,
+ struct spi_device *pspi)
+{
+ if (data->current_chip != NULL) {
+ if (pspi->chip_select != data->n_curnt_chip) {
+ dev_dbg(&pspi->dev, "%s : different slave\n", __func__);
+ data->current_chip = NULL;
+ }
+ }
+
+ data->current_chip = pspi;
+
+ data->n_curnt_chip = data->current_chip->chip_select;
+
+ dev_dbg(&pspi->dev, "%s :Invoking pch_spi_setup_transfer\n", __func__);
+ pch_spi_setup_transfer(pspi);
+}
+
+static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw,
+ struct spi_message **ppmsg)
+{
+ int size;
+ u32 n_writes;
+ int j;
+ struct spi_message *pmsg;
+ const u8 *tx_buf;
+ const u16 *tx_sbuf;
+
+ pmsg = *ppmsg;
+
+ /* set baud rate if needed */
+ if (data->cur_trans->speed_hz) {
+ dev_dbg(&data->master->dev, "%s:setting baud rate\n", __func__);
+ pch_spi_set_baud_rate(data->master, data->cur_trans->speed_hz);
+ }
+
+ /* set bits per word if needed */
+ if (data->cur_trans->bits_per_word &&
+ (data->current_msg->spi->bits_per_word != data->cur_trans->bits_per_word)) {
+ dev_dbg(&data->master->dev, "%s:set bits per word\n", __func__);
+ pch_spi_set_bits_per_word(data->master,
+ data->cur_trans->bits_per_word);
+ *bpw = data->cur_trans->bits_per_word;
+ } else {
+ *bpw = data->current_msg->spi->bits_per_word;
+ }
+
+ /* reset Tx/Rx index */
+ data->tx_index = 0;
+ data->rx_index = 0;
+
+ data->bpw_len = data->cur_trans->len / (*bpw / 8);
+
+ /* find alloc size */
+ size = data->cur_trans->len * sizeof(*data->pkt_tx_buff);
+
+ /* allocate memory for pkt_tx_buff & pkt_rx_buffer */
+ data->pkt_tx_buff = kzalloc(size, GFP_KERNEL);
+ if (data->pkt_tx_buff != NULL) {
+ data->pkt_rx_buff = kzalloc(size, GFP_KERNEL);
+ if (!data->pkt_rx_buff)
+ kfree(data->pkt_tx_buff);
+ }
+
+ if (!data->pkt_rx_buff) {
+ /* flush queue and set status of all transfers to -ENOMEM */
+ dev_err(&data->master->dev, "%s :kzalloc failed\n", __func__);
+ list_for_each_entry(pmsg, data->queue.next, queue) {
+ pmsg->status = -ENOMEM;
+
+ if (pmsg->complete != 0)
+ pmsg->complete(pmsg->context);
+
+ /* delete from queue */
+ list_del_init(&pmsg->queue);
+ }
+ return;
+ }
+
+ /* copy Tx Data */
+ if (data->cur_trans->tx_buf != NULL) {
+ if (*bpw == 8) {
+ tx_buf = data->cur_trans->tx_buf;
+ for (j = 0; j < data->bpw_len; j++)
+ data->pkt_tx_buff[j] = *tx_buf++;
+ } else {
+ tx_sbuf = data->cur_trans->tx_buf;
+ for (j = 0; j < data->bpw_len; j++)
+ data->pkt_tx_buff[j] = *tx_sbuf++;
+ }
+ }
+
+ /* if len greater than PCH_MAX_FIFO_DEPTH, write 16,else len bytes */
+ n_writes = data->bpw_len;
+ if (n_writes > PCH_MAX_FIFO_DEPTH)
+ n_writes = PCH_MAX_FIFO_DEPTH;
+
+ dev_dbg(&data->master->dev, "\n%s:Pulling down SSN low - writing "
+ "0x2 to SSNXCR\n", __func__);
+ pch_spi_writereg(data->master, PCH_SSNXCR, SSN_LOW);
+
+ for (j = 0; j < n_writes; j++)
+ pch_spi_writereg(data->master, PCH_SPDWR, data->pkt_tx_buff[j]);
+
+ /* update tx_index */
+ data->tx_index = j;
+
+ /* reset transfer complete flag */
+ data->transfer_complete = false;
+ data->transfer_active = true;
+}
+
+
+static void pch_spi_nomore_transfer(struct pch_spi_data *data,
+ struct spi_message *pmsg)
+{
+ dev_dbg(&data->master->dev, "%s called\n", __func__);
+ /* Invoke complete callback
+ * [To the spi core..indicating end of transfer] */
+ data->current_msg->status = 0;
+
+ if (data->current_msg->complete != 0) {
+ dev_dbg(&data->master->dev,
+ "%s:Invoking callback of SPI core\n", __func__);
+ data->current_msg->complete(data->current_msg->context);
+ }
+
+ /* update status in global variable */
+ data->bcurrent_msg_processing = false;
+
+ dev_dbg(&data->master->dev,
+ "%s:data->bcurrent_msg_processing = false\n", __func__);
+
+ data->current_msg = NULL;
+ data->cur_trans = NULL;
+
+ /* check if we have items in list and not suspending
+ * return 1 if list empty */
+ if ((list_empty(&data->queue) == 0) &&
+ (!data->board_dat->suspend_sts) &&
+ (data->status != STATUS_EXITING)) {
+ /* We have some more work to do (either there is more tranint
+ * bpw;sfer requests in the current message or there are
+ *more messages)
+ */
+ dev_dbg(&data->master->dev, "%s:Invoke queue_work\n", __func__);
+ queue_work(data->wk, &data->work);
+ } else if (data->board_dat->suspend_sts ||
+ data->status == STATUS_EXITING) {
+ dev_dbg(&data->master->dev,
+ "%s suspend/remove initiated, flushing queue\n",
+ __func__);
+ list_for_each_entry(pmsg, data->queue.next, queue) {
+ pmsg->status = -EIO;
+
+ if (pmsg->complete)
+ pmsg->complete(pmsg->context);
+
+ /* delete from queue */
+ list_del_init(&pmsg->queue);
+ }
+ }
+}
+
+static void pch_spi_set_ir(struct pch_spi_data *data)
+{
+ /* enable interrupts */
+ if ((data->bpw_len) > PCH_MAX_FIFO_DEPTH) {
+ /* set receive threhold to PCH_RX_THOLD */
+ pch_spi_setclr_reg(data->master, PCH_SPCR,
+ PCH_RX_THOLD << SPCR_TFIC_FIELD,
+ ~MASK_TFIC_SPCR_BITS);
+ /* enable FI and RFI interrupts */
+ pch_spi_setclr_reg(data->master, PCH_SPCR,
+ SPCR_RFIE_BIT | SPCR_TFIE_BIT, 0);
+ } else {
+ /* set receive threhold to maximum */
+ pch_spi_setclr_reg(data->master, PCH_SPCR,
+ PCH_RX_THOLD_MAX << SPCR_TFIC_FIELD,
+ ~MASK_TFIC_SPCR_BITS);
+ /* enable FI interrupt */
+ pch_spi_setclr_reg(data->master, PCH_SPCR, SPCR_FIE_BIT, 0);
+ }
+
+ dev_dbg(&data->master->dev,
+ "%s:invoking pch_spi_set_enable to enable SPI\n", __func__);
+
+ /* SPI set enable */
+ pch_spi_setclr_reg(data->current_chip->master, PCH_SPCR, SPCR_SPE_BIT, 0);
+
+ /* Wait until the transfer completes; go to sleep after
+ initiating the transfer. */
+ dev_dbg(&data->master->dev,
+ "%s:waiting for transfer to get over\n", __func__);
+
+ wait_event_interruptible(data->wait, data->transfer_complete);
+
+ pch_spi_writereg(data->master, PCH_SSNXCR, SSN_NO_CONTROL);
+ dev_dbg(&data->master->dev,
+ "%s:no more control over SSN-writing 0 to SSNXCR.", __func__);
+
+ data->transfer_active = false;
+ dev_dbg(&data->master->dev,
+ "%s set data->transfer_active = false\n", __func__);
+
+ /* clear all interrupts */
+ pch_spi_writereg(data->master, PCH_SPSR,
+ pch_spi_readreg(data->master, PCH_SPSR));
+ /* disable interrupts */
+ pch_spi_setclr_reg(data->master, PCH_SPCR, 0, PCH_ALL);
+}
+
+static void pch_spi_copy_rx_data(struct pch_spi_data *data, int bpw)
+{
+ int j;
+ u8 *rx_buf;
+ u16 *rx_sbuf;
+
+ /* copy Rx Data */
+ if (!data->cur_trans->rx_buf)
+ return;
+
+ if (bpw == 8) {
+ rx_buf = data->cur_trans->rx_buf;
+ for (j = 0; j < data->bpw_len; j++)
+ *rx_buf++ = data->pkt_rx_buff[j] & 0xFF;
+ } else {
+ rx_sbuf = data->cur_trans->rx_buf;
+ for (j = 0; j < data->bpw_len; j++)
+ *rx_sbuf++ = data->pkt_rx_buff[j];
+ }
+}
+
+
+static void pch_spi_process_messages(struct work_struct *pwork)
+{
+ struct spi_message *pmsg;
+ struct pch_spi_data *data;
+ int bpw;
+
+ dev_dbg(&data->master->dev, "%s data initialized\n", __func__);
+ data = container_of(pwork, struct pch_spi_data, work);
+
+ spin_lock(&data->lock);
+
+ /* check if suspend has been initiated;if yes flush queue */
+ if (data->board_dat->suspend_sts || (data->status == STATUS_EXITING)) {
+ dev_dbg(&data->master->dev,
+ "%s suspend/remove initiated,flushing queue\n",
+ __func__);
+
+ list_for_each_entry(pmsg, data->queue.next, queue) {
+ pmsg->status = -EIO;
+
+ if (pmsg->complete != 0) {
+ spin_unlock(&data->lock);
+ pmsg->complete(pmsg->context);
+ spin_lock(&data->lock);
+ }
+
+ /* delete from queue */
+ list_del_init(&pmsg->queue);
+ }
+
+ spin_unlock(&data->lock);
+ return;
+ }
+
+ data->bcurrent_msg_processing = true;
+ dev_dbg(&data->master->dev,
+ "%s Set data->bcurrent_msg_processing= true\n", __func__);
+
+ /* Get the message from the queue and delete it from there. */
+ data->current_msg = list_entry(data->queue.next, struct spi_message,
+ queue);
+
+ list_del_init(&data->current_msg->queue);
+
+ data->current_msg->status = 0;
+
+ pch_spi_select_chip(data, data->current_msg->spi);
+
+ spin_unlock(&data->lock);
+
+ do {
+ /* If we are already processing a message get the next
+ transfer structure from the message otherwise retrieve
+ the 1st transfer request from the message. */
+ spin_lock(&data->lock);
+
+ if (data->cur_trans == NULL) {
+ data->cur_trans =
+ list_entry(data->current_msg->transfers.
+ next, struct spi_transfer,
+ transfer_list);
+ dev_dbg(&data->master->dev,
+ "%s :Getting 1st transfer message\n", __func__);
+ } else {
+ data->cur_trans =
+ list_entry(data->cur_trans->transfer_list.next,
+ struct spi_transfer,
+ transfer_list);
+ dev_dbg(&data->master->dev,
+ "%s :Getting next transfer message\n",
+ __func__);
+ }
+
+ spin_unlock(&data->lock);
+
+ pch_spi_set_tx(data, &bpw, &pmsg);
+
+ /* Control interrupt*/
+ pch_spi_set_ir(data);
+
+ /* Disable SPI transfer */
+ pch_spi_setclr_reg(data->current_chip->master, PCH_SPCR, 0,
+ SPCR_SPE_BIT);
+
+ /* clear FIFO */
+ pch_spi_clear_fifo(data->master);
+
+ /* copy Rx Data */
+ pch_spi_copy_rx_data(data, bpw);
+
+ /* free memory */
+ kfree(data->pkt_rx_buff);
+ data->pkt_rx_buff = NULL;
+
+ kfree(data->pkt_tx_buff);
+ data->pkt_tx_buff = NULL;
+
+ /* increment message count */
+ data->current_msg->actual_length += data->cur_trans->len;
+
+ dev_dbg(&data->master->dev,
+ "%s:data->current_msg->actual_length=%d\n",
+ __func__, data->current_msg->actual_length);
+
+ /* check for delay */
+ if (data->cur_trans->delay_usecs) {
+ dev_dbg(&data->master->dev, "%s:"
+ "delay in usec=%d\n", __func__,
+ data->cur_trans->delay_usecs);
+ udelay(data->cur_trans->delay_usecs);
+ }
+
+ spin_lock(&data->lock);
+
+ /* No more transfer in this message. */
+ if ((data->cur_trans->transfer_list.next) ==
+ &(data->current_msg->transfers)) {
+ pch_spi_nomore_transfer(data, pmsg);
+ }
+
+ spin_unlock(&data->lock);
+
+ } while (data->cur_trans != NULL);
+}
+
+static void pch_spi_free_resources(struct pch_spi_board_data *board_dat)
+{
+ dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__);
+
+ /* free workqueue */
+ if (board_dat->data->wk != NULL) {
+ destroy_workqueue(board_dat->data->wk);
+ board_dat->data->wk = NULL;
+ dev_dbg(&board_dat->pdev->dev,
+ "%s destroy_workqueue invoked successfully\n",
+ __func__);
+ }
+
+ /* disable interrupts & free IRQ */
+ if (board_dat->irq_reg_sts) {
+ /* disable interrupts */
+ pch_spi_setclr_reg(board_dat->data->master, PCH_SPCR, 0,
+ PCH_ALL);
+
+ /* free IRQ */
+ free_irq(board_dat->pdev->irq, board_dat);
+
+ dev_dbg(&board_dat->pdev->dev,
+ "%s free_irq invoked successfully\n", __func__);
+
+ board_dat->irq_reg_sts = false;
+ }
+
+ /* unmap PCI base address */
+ if (board_dat->data->io_remap_addr != 0) {
+ pci_iounmap(board_dat->pdev, board_dat->data->io_remap_addr);
+
+ board_dat->data->io_remap_addr = 0;
+
+ dev_dbg(&board_dat->pdev->dev,
+ "%s pci_iounmap invoked successfully\n", __func__);
+ }
+
+ /* release PCI region */
+ if (board_dat->pci_req_sts) {
+ pci_release_regions(board_dat->pdev);
+ dev_dbg(&board_dat->pdev->dev,
+ "%s pci_release_regions invoked successfully\n",
+ __func__);
+ board_dat->pci_req_sts = false;
+ }
+}
+
+static int pch_spi_get_resources(struct pch_spi_board_data *board_dat)
+{
+ void __iomem *io_remap_addr;
+ int retval;
+ dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__);
+
+ /* create workqueue */
+ board_dat->data->wk = create_singlethread_workqueue(KBUILD_MODNAME);
+ if (!board_dat->data->wk) {
+ dev_err(&board_dat->pdev->dev,
+ "%s create_singlet hread_workqueue failed\n", __func__);
+ retval = -EBUSY;
+ goto err_return;
+ }
+
+ dev_dbg(&board_dat->pdev->dev,
+ "%s create_singlethread_workqueue success\n", __func__);
+
+ retval = pci_request_regions(board_dat->pdev, KBUILD_MODNAME);
+ if (retval != 0) {
+ dev_err(&board_dat->pdev->dev,
+ "%s request_region failed\n", __func__);
+ goto err_return;
+ }
+
+ board_dat->pci_req_sts = true;
+
+ io_remap_addr = pci_iomap(board_dat->pdev, 1, 0);
+ if (io_remap_addr == 0) {
+ dev_err(&board_dat->pdev->dev,
+ "%s pci_iomap failed\n", __func__);
+ retval = -ENOMEM;
+ goto err_return;
+ }
+
+ /* calculate base address for all channels */
+ board_dat->data->io_remap_addr = io_remap_addr;
+
+ /* reset PCH SPI h/w */
+ pch_spi_reset(board_dat->data->master);
+ dev_dbg(&board_dat->pdev->dev,
+ "%s pch_spi_reset invoked successfully\n", __func__);
+
+ /* register IRQ */
+ retval = request_irq(board_dat->pdev->irq, pch_spi_handler,
+ IRQF_SHARED, KBUILD_MODNAME, board_dat);
+ if (retval != 0) {
+ dev_err(&board_dat->pdev->dev,
+ "%s request_irq failed\n", __func__);
+ goto err_return;
+ }
+
+ dev_dbg(&board_dat->pdev->dev, "%s request_irq returned=%d\n",
+ __func__, retval);
+
+ board_dat->irq_reg_sts = true;
+ dev_dbg(&board_dat->pdev->dev, "%s data->irq_reg_sts=true\n", __func__);
+
+err_return:
+ if (retval != 0) {
+ dev_err(&board_dat->pdev->dev,
+ "%s FAIL:invoking pch_spi_free_resources\n", __func__);
+ pch_spi_free_resources(board_dat);
+ }
+
+ dev_dbg(&board_dat->pdev->dev, "%s Return=%d\n", __func__, retval);
+
+ return retval;
+}
+
+static int pch_spi_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+
+ struct spi_master *master;
+
+ struct pch_spi_board_data *board_dat;
+ int retval;
+
+ dev_dbg(&pdev->dev, "%s ENTRY\n", __func__);
+
+ /* allocate memory for private data */
+ board_dat = kzalloc(sizeof(struct pch_spi_board_data), GFP_KERNEL);
+ if (board_dat == NULL) {
+ dev_err(&pdev->dev,
+ " %s memory allocation for private data failed\n",
+ __func__);
+ retval = -ENOMEM;
+ goto err_kmalloc;
+ }
+
+ dev_dbg(&pdev->dev,
+ "%s memory allocation for private data success\n", __func__);
+
+ /* enable PCI device */
+ retval = pci_enable_device(pdev);
+ if (retval != 0) {
+ dev_err(&pdev->dev, "%s pci_enable_device FAILED\n", __func__);
+
+ goto err_pci_en_device;
+ }
+
+ dev_dbg(&pdev->dev, "%s pci_enable_device returned=%d\n",
+ __func__, retval);
+
+ board_dat->pdev = pdev;
+
+ /* alllocate memory for SPI master */
+ master = spi_alloc_master(&pdev->dev, sizeof(struct pch_spi_data));
+ if (master == NULL) {
+ retval = -ENOMEM;
+ dev_err(&pdev->dev, "%s Fail.\n", __func__);
+ goto err_spi_alloc_master;
+ }
+
+ dev_dbg(&pdev->dev,
+ "%s spi_alloc_master returned non NULL\n", __func__);
+
+ /* initialize members of SPI master */
+ master->bus_num = -1;
+ master->num_chipselect = PCH_MAX_CS;
+ master->setup = pch_spi_setup;
+ master->transfer = pch_spi_transfer;
+ dev_dbg(&pdev->dev,
+ "%s transfer member of SPI master initialized\n", __func__);
+
+ board_dat->data = spi_master_get_devdata(master);
+
+ board_dat->data->master = master;
+ board_dat->data->n_curnt_chip = 255;
+ board_dat->data->board_dat = board_dat;
+ board_dat->data->status = STATUS_RUNNING;
+
+ INIT_LIST_HEAD(&board_dat->data->queue);
+ spin_lock_init(&board_dat->data->lock);
+ INIT_WORK(&board_dat->data->work, pch_spi_process_messages);
+ init_waitqueue_head(&board_dat->data->wait);
+
+ /* allocate resources for PCH SPI */
+ retval = pch_spi_get_resources(board_dat);
+ if (retval) {
+ dev_err(&pdev->dev, "%s fail(retval=%d)\n", __func__, retval);
+ goto err_spi_get_resources;
+ }
+
+ dev_dbg(&pdev->dev, "%s pch_spi_get_resources returned=%d\n",
+ __func__, retval);
+
+ /* save private data in dev */
+ pci_set_drvdata(pdev, board_dat);
+ dev_dbg(&pdev->dev, "%s invoked pci_set_drvdata\n", __func__);
+
+ /* set master mode */
+ pch_spi_set_master_mode(master);
+ dev_dbg(&pdev->dev,
+ "%s invoked pch_spi_set_master_mode\n", __func__);
+
+ /* Register the controller with the SPI core. */
+ retval = spi_register_master(master);
+ if (retval != 0) {
+ dev_err(&pdev->dev,
+ "%s spi_register_master FAILED\n", __func__);
+ goto err_spi_reg_master;
+ }
+
+ dev_dbg(&pdev->dev, "%s spi_register_master returned=%d\n",
+ __func__, retval);
+
+
+ return 0;
+
+err_spi_reg_master:
+ spi_unregister_master(master);
+err_spi_get_resources:
+err_spi_alloc_master:
+ spi_master_put(master);
+ pci_disable_device(pdev);
+err_pci_en_device:
+ kfree(board_dat);
+err_kmalloc:
+ return retval;
+}
+
+static void pch_spi_remove(struct pci_dev *pdev)
+{
+ struct pch_spi_board_data *board_dat = pci_get_drvdata(pdev);
+ int count;
+
+ dev_dbg(&pdev->dev, "%s ENTRY\n", __func__);
+
+ if (!board_dat) {
+ dev_err(&pdev->dev,
+ "%s pci_get_drvdata returned NULL\n", __func__);
+ return;
+ }
+
+ /* check for any pending messages; no action is taken if the queue
+ * is still full; but at least we tried. Unload anyway */
+ count = 500;
+ spin_lock(&board_dat->data->lock);
+ board_dat->data->status = STATUS_EXITING;
+ while ((list_empty(&board_dat->data->queue) == 0) && --count) {
+ dev_dbg(&board_dat->pdev->dev, "%s :queue not empty\n",
+ __func__);
+ spin_unlock(&board_dat->data->lock);
+ msleep(PCH_SLEEP_TIME);
+ spin_lock(&board_dat->data->lock);
+ }
+ spin_unlock(&board_dat->data->lock);
+
+ /* Free resources allocated for PCH SPI */
+ pch_spi_free_resources(board_dat);
+
+ spi_unregister_master(board_dat->data->master);
+
+ /* free memory for private data */
+ kfree(board_dat);
+
+ pci_set_drvdata(pdev, NULL);
+
+ /* disable PCI device */
+ pci_disable_device(pdev);
+
+ dev_dbg(&pdev->dev, "%s invoked pci_disable_device\n", __func__);
+}
+
+#ifdef CONFIG_PM
+static int pch_spi_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ u8 count;
+ int retval;
+
+ struct pch_spi_board_data *board_dat = pci_get_drvdata(pdev);
+
+ dev_dbg(&pdev->dev, "%s ENTRY\n", __func__);
+
+ if (!board_dat) {
+ dev_err(&pdev->dev,
+ "%s pci_get_drvdata returned NULL\n", __func__);
+ return -EFAULT;
+ }
+
+ retval = 0;
+ board_dat->suspend_sts = true;
+
+ /* check if the current message is processed:
+ Only after thats done the transfer will be suspended */
+ count = 255;
+ while ((--count) > 0) {
+ if (!(board_dat->data->bcurrent_msg_processing)) {
+ dev_dbg(&pdev->dev, "%s board_dat->data->bCurrent_"
+ "msg_processing = false\n", __func__);
+ break;
+ } else {
+ dev_dbg(&pdev->dev, "%s board_dat->data->bCurrent_msg_"
+ "processing = true\n", __func__);
+ }
+ msleep(PCH_SLEEP_TIME);
+ }
+
+ /* Free IRQ */
+ if (board_dat->irq_reg_sts) {
+ /* disable all interrupts */
+ pch_spi_setclr_reg(board_dat->data->master, PCH_SPCR, 0,
+ PCH_ALL);
+ pch_spi_reset(board_dat->data->master);
+
+ free_irq(board_dat->pdev->irq, board_dat);
+
+ board_dat->irq_reg_sts = false;
+ dev_dbg(&pdev->dev,
+ "%s free_irq invoked successfully.\n", __func__);
+ }
+
+ /* save config space */
+ retval = pci_save_state(pdev);
+
+ if (retval == 0) {
+ dev_dbg(&pdev->dev, "%s pci_save_state returned=%d\n",
+ __func__, retval);
+ /* disable PM notifications */
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ dev_dbg(&pdev->dev,
+ "%s pci_enable_wake invoked successfully\n", __func__);
+ /* disable PCI device */
+ pci_disable_device(pdev);
+ dev_dbg(&pdev->dev,
+ "%s pci_disable_device invoked successfully\n",
+ __func__);
+ /* move device to D3hot state */
+ pci_set_power_state(pdev, PCI_D3hot);
+ dev_dbg(&pdev->dev,
+ "%s pci_set_power_state invoked successfully\n",
+ __func__);
+ } else {
+ dev_err(&pdev->dev, "%s pci_save_state failed\n", __func__);
+ }
+
+ dev_dbg(&pdev->dev, "%s return=%d\n", __func__, retval);
+
+ return retval;
+}
+
+static int pch_spi_resume(struct pci_dev *pdev)
+{
+ int retval;
+
+ struct pch_spi_board_data *board = pci_get_drvdata(pdev);
+ dev_dbg(&pdev->dev, "%s ENTRY\n", __func__);
+
+ if (!board) {
+ dev_err(&pdev->dev,
+ "%s pci_get_drvdata returned NULL\n", __func__);
+ return -EFAULT;
+ }
+
+ /* move device to DO power state */
+ pci_set_power_state(pdev, PCI_D0);
+
+ /* restore state */
+ pci_restore_state(pdev);
+
+ retval = pci_enable_device(pdev);
+ if (retval < 0) {
+ dev_err(&pdev->dev,
+ "%s pci_enable_device failed\n", __func__);
+ } else {
+ /* disable PM notifications */
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+
+ /* register IRQ handler */
+ if (!board->irq_reg_sts) {
+ /* register IRQ */
+ retval = request_irq(board->pdev->irq, pch_spi_handler,
+ IRQF_SHARED, KBUILD_MODNAME,
+ board);
+ if (retval < 0) {
+ dev_err(&pdev->dev,
+ "%s request_irq failed\n", __func__);
+ return retval;
+ }
+ board->irq_reg_sts = true;
+
+ /* reset PCH SPI h/w */
+ pch_spi_reset(board->data->master);
+ pch_spi_set_master_mode(board->data->master);
+
+ /* set suspend status to false */
+ board->suspend_sts = false;
+
+ }
+ }
+
+ dev_dbg(&pdev->dev, "%s returning=%d\n", __func__, retval);
+
+ return retval;
+}
+#else
+#define pch_spi_suspend NULL
+#define pch_spi_resume NULL
+
+#endif
+
+static struct pci_driver pch_spi_pcidev = {
+ .name = "pch_spi",
+ .id_table = pch_spi_pcidev_id,
+ .probe = pch_spi_probe,
+ .remove = pch_spi_remove,
+ .suspend = pch_spi_suspend,
+ .resume = pch_spi_resume,
+};
+
+static int __init pch_spi_init(void)
+{
+ return pci_register_driver(&pch_spi_pcidev);
+}
+module_init(pch_spi_init);
+
+static void __exit pch_spi_exit(void)
+{
+ pci_unregister_driver(&pch_spi_pcidev);
+}
+module_exit(pch_spi_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Topcliff PCH SPI PCI Driver");
diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h
index abf26cc..4ce98f5 100644
--- a/include/linux/amba/pl022.h
+++ b/include/linux/amba/pl022.h
@@ -228,6 +228,7 @@
};
+struct dma_chan;
/**
* struct pl022_ssp_master - device.platform_data for SPI controller devices.
* @num_chipselect: chipselects are used to distinguish individual
@@ -235,11 +236,16 @@
* each slave has a chipselect signal, but it's common that not
* every chipselect is connected to a slave.
* @enable_dma: if true enables DMA driven transfers.
+ * @dma_rx_param: parameter to locate an RX DMA channel.
+ * @dma_tx_param: parameter to locate a TX DMA channel.
*/
struct pl022_ssp_controller {
u16 bus_id;
u8 num_chipselect;
u8 enable_dma:1;
+ bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
+ void *dma_rx_param;
+ void *dma_tx_param;
};
/**
@@ -270,20 +276,13 @@
* @dma_config: DMA configuration for SSP controller and peripheral
*/
struct pl022_config_chip {
- struct device *dev;
- enum ssp_loopback lbm;
enum ssp_interface iface;
enum ssp_hierarchy hierarchy;
bool slave_tx_disable;
struct ssp_clock_params clk_freq;
- enum ssp_rx_endian endian_rx;
- enum ssp_tx_endian endian_tx;
- enum ssp_data_size data_size;
enum ssp_mode com_mode;
enum ssp_rx_level_trig rx_lev_trig;
enum ssp_tx_level_trig tx_lev_trig;
- enum ssp_spi_clk_phase clk_phase;
- enum ssp_spi_clk_pol clk_pol;
enum ssp_microwire_ctrl_len ctrl_len;
enum ssp_microwire_wait_state wait_state;
enum ssp_duplex duplex;