diff --git a/include/asm-sh/sh7760fb.h b/include/asm-sh/sh7760fb.h
new file mode 100644
index 0000000..8767f61
--- /dev/null
+++ b/include/asm-sh/sh7760fb.h
@@ -0,0 +1,197 @@
+/*
+ * sh7760fb.h -- platform data for SH7760/SH7763 LCDC framebuffer driver.
+ *
+ * (c) 2006-2008 MSC Vertriebsges.m.b.H.,
+ * 			Manuel Lauss <mano@roarinelk.homelinux.net>
+ * (c) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
+ */
+
+#ifndef _ASM_SH_SH7760FB_H
+#define _ASM_SH_SH7760FB_H
+
+/*
+ * some bits of the colormap registers should be written as zero.
+ * create a mask for that.
+ */
+#define SH7760FB_PALETTE_MASK 0x00f8fcf8
+
+/* The LCDC dma engine always sets bits 27-26 to 1: this is Area3 */
+#define SH7760FB_DMA_MASK 0x0C000000
+
+/* palette */
+#define LDPR(x) (((x) << 2))
+
+/* framebuffer registers and bits */
+#define LDICKR 0x400
+#define LDMTR 0x402
+/* see sh7760fb.h for LDMTR bits */
+#define LDDFR 0x404
+#define LDDFR_PABD (1 << 8)
+#define LDDFR_COLOR_MASK 0x7F
+#define LDSMR 0x406
+#define LDSMR_ROT (1 << 13)
+#define LDSARU 0x408
+#define LDSARL 0x40c
+#define LDLAOR 0x410
+#define LDPALCR 0x412
+#define LDPALCR_PALS (1 << 4)
+#define LDPALCR_PALEN (1 << 0)
+#define LDHCNR 0x414
+#define LDHSYNR 0x416
+#define LDVDLNR 0x418
+#define LDVTLNR 0x41a
+#define LDVSYNR 0x41c
+#define LDACLNR 0x41e
+#define LDINTR 0x420
+#define LDPMMR 0x424
+#define LDPSPR 0x426
+#define LDCNTR 0x428
+#define LDCNTR_DON (1 << 0)
+#define LDCNTR_DON2 (1 << 4)
+
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+# define LDLIRNR       0x440
+/* LDINTR bit */
+# define LDINTR_MINTEN (1 << 15)
+# define LDINTR_FINTEN (1 << 14)
+# define LDINTR_VSINTEN (1 << 13)
+# define LDINTR_VEINTEN (1 << 12)
+# define LDINTR_MINTS (1 << 11)
+# define LDINTR_FINTS (1 << 10)
+# define LDINTR_VSINTS (1 << 9)
+# define LDINTR_VEINTS (1 << 8)
+# define VINT_START (LDINTR_VSINTEN)
+# define VINT_CHECK (LDINTR_VSINTS)
+#else
+/* LDINTR bit */
+# define LDINTR_VINTSEL (1 << 12)
+# define LDINTR_VINTE (1 << 8)
+# define LDINTR_VINTS (1 << 0)
+# define VINT_START (LDINTR_VINTSEL)
+# define VINT_CHECK (LDINTR_VINTS)
+#endif
+
+/* HSYNC polarity inversion */
+#define LDMTR_FLMPOL (1 << 15)
+
+/* VSYNC polarity inversion */
+#define LDMTR_CL1POL (1 << 14)
+
+/* DISPLAY-ENABLE polarity inversion */
+#define LDMTR_DISPEN_LOWACT (1 << 13)
+
+/* DISPLAY DATA BUS polarity inversion */
+#define LDMTR_DPOL_LOWACT (1 << 12)
+
+/* AC modulation signal enable */
+#define LDMTR_MCNT (1 << 10)
+
+/* Disable output of HSYNC during VSYNC period */
+#define LDMTR_CL1CNT (1 << 9)
+
+/* Disable output of VSYNC during VSYNC period */
+#define LDMTR_CL2CNT (1 << 8)
+
+/* Display types supported by the LCDC */
+#define LDMTR_STN_MONO_4       0x00
+#define LDMTR_STN_MONO_8       0x01
+#define LDMTR_STN_COLOR_4      0x08
+#define LDMTR_STN_COLOR_8      0x09
+#define LDMTR_STN_COLOR_12     0x0A
+#define LDMTR_STN_COLOR_16     0x0B
+#define LDMTR_DSTN_MONO_8      0x11
+#define LDMTR_DSTN_MONO_16     0x13
+#define LDMTR_DSTN_COLOR_8     0x19
+#define LDMTR_DSTN_COLOR_12    0x1A
+#define LDMTR_DSTN_COLOR_16    0x1B
+#define LDMTR_TFT_COLOR_16     0x2B
+
+/* framebuffer color layout */
+#define LDDFR_1BPP_MONO 0x00
+#define LDDFR_2BPP_MONO 0x01
+#define LDDFR_4BPP_MONO 0x02
+#define LDDFR_6BPP_MONO 0x04
+#define LDDFR_4BPP 0x0A
+#define LDDFR_8BPP 0x0C
+#define LDDFR_16BPP_RGB555 0x1D
+#define LDDFR_16BPP_RGB565 0x2D
+
+/* LCDC Pixclock sources */
+#define LCDC_CLKSRC_BUSCLOCK 0
+#define LCDC_CLKSRC_PERIPHERAL 1
+#define LCDC_CLKSRC_EXTERNAL 2
+
+#define LDICKR_CLKSRC(x) \
+       (((x) & 3) << 12)
+
+/* LCDC pixclock input divider. Set to 1 at a minimum! */
+#define LDICKR_CLKDIV(x) \
+       ((x) & 0x1f)
+
+struct sh7760fb_platdata {
+
+	/* Set this member to a valid fb_videmode for the display you
+	 * wish to use.  The following members must be initialized:
+	 * xres, yres, hsync_len, vsync_len, sync,
+	 * {left,right,upper,lower}_margin.
+	 * The driver uses the above members to calculate register values
+	 * and memory requirements. Other members are ignored but may
+	 * be used by other framebuffer layer components.
+	 */
+	struct fb_videomode *def_mode;
+
+	/* LDMTR includes display type and signal polarity.  The
+	 * HSYNC/VSYNC polarities are derived from the fb_var_screeninfo
+	 * data above; however the polarities of the following signals
+	 * must be encoded in the ldmtr member:
+	 * Display Enable signal (default high-active)  DISPEN_LOWACT
+	 * Display Data signals (default high-active)   DPOL_LOWACT
+	 * AC Modulation signal (default off)           MCNT
+	 * Hsync-During-Vsync suppression (default off) CL1CNT
+	 * Vsync-during-vsync suppression (default off) CL2CNT
+	 * NOTE: also set a display type!
+	 * (one of LDMTR_{STN,DSTN,TFT}_{MONO,COLOR}_{4,8,12,16})
+	 */
+	u16 ldmtr;
+
+	/* LDDFR controls framebuffer image format (depth, organization)
+	 * Use ONE of the LDDFR_?BPP_* macros!
+	 */
+	u16 lddfr;
+
+	/* LDPMMR and LDPSPR control the timing of the power signals
+	 * for the display. Please read the SH7760 Hardware Manual,
+	 * Chapters 30.3.17, 30.3.18 and 30.4.6!
+	 */
+	u16 ldpmmr;
+	u16 ldpspr;
+
+	/* LDACLNR contains the line numbers after which the AC modulation
+	 * signal is to toggle. Set to ZERO for TFTs or displays which
+	 * do not need it. (Chapter 30.3.15 in SH7760 Hardware Manual).
+	 */
+	u16 ldaclnr;
+
+	/* LDICKR contains information on pixelclock source and config.
+	 * Please use the LDICKR_CLKSRC() and LDICKR_CLKDIV() macros.
+	 * minimal value for CLKDIV() must be 1!.
+	 */
+	u16 ldickr;
+
+	/* set this member to 1 if you wish to use the LCDC's hardware
+	 * rotation function.  This is limited to displays <= 320x200
+	 * pixels resolution!
+	 */
+	int rotate;		/* set to 1 to rotate 90 CCW */
+
+	/* set this to 1 to suppress vsync irq use. */
+	int novsync;
+
+	/* blanking hook for platform. Set this if your platform can do
+	 * more than the LCDC in terms of blanking (e.g. disable clock
+	 * generator / backlight power supply / etc.
+	 */
+	void (*blank) (int);
+};
+
+#endif /* _ASM_SH_SH7760FB_H */