libata: fix device iteration bugs
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.
* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()
While at it, reformat comments in cable_is_40wire().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 8cb0b36..97df480 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4156,29 +4156,33 @@
struct ata_link *link;
struct ata_device *dev;
- /* If the controller thinks we are 40 wire, we are */
+ /* If the controller thinks we are 40 wire, we are. */
if (ap->cbl == ATA_CBL_PATA40)
return 1;
- /* If the controller thinks we are 80 wire, we are */
+
+ /* If the controller thinks we are 80 wire, we are. */
if (ap->cbl == ATA_CBL_PATA80 || ap->cbl == ATA_CBL_SATA)
return 0;
- /* If the system is known to be 40 wire short cable (eg laptop),
- then we allow 80 wire modes even if the drive isn't sure */
+
+ /* If the system is known to be 40 wire short cable (eg
+ * laptop), then we allow 80 wire modes even if the drive
+ * isn't sure.
+ */
if (ap->cbl == ATA_CBL_PATA40_SHORT)
return 0;
- /* If the controller doesn't know we scan
- - Note: We look for all 40 wire detects at this point.
- Any 80 wire detect is taken to be 80 wire cable
- because
- - In many setups only the one drive (slave if present)
- will give a valid detect
- - If you have a non detect capable drive you don't
- want it to colour the choice
- */
+ /* If the controller doesn't know, we scan.
+ *
+ * Note: We look for all 40 wire detects at this point. Any
+ * 80 wire detect is taken to be 80 wire cable because
+ * - in many setups only the one drive (slave if present) will
+ * give a valid detect
+ * - if you have a non detect capable drive you don't want it
+ * to colour the choice
+ */
ata_port_for_each_link(link, ap) {
ata_link_for_each_dev(dev, link) {
- if (!ata_is_40wire(dev))
+ if (ata_dev_enabled(dev) && !ata_is_40wire(dev))
return 0;
}
}
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 5d687d7..a6a3b15 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -603,6 +603,9 @@
ata_link_for_each_dev(dev, link) {
int devno = dev->devno;
+ if (!ata_dev_enabled(dev))
+ continue;
+
ehc->saved_xfer_mode[devno] = dev->xfer_mode;
if (ata_ncq_enabled(dev))
ehc->saved_ncq_enabled |= 1 << devno;
@@ -2787,6 +2790,9 @@
/* if data transfer is verified, clear DUBIOUS_XFER on ering top */
ata_link_for_each_dev(dev, link) {
+ if (!ata_dev_enabled(dev))
+ continue;
+
if (!(dev->flags & ATA_DFLAG_DUBIOUS_XFER)) {
struct ata_ering_entry *ent;
@@ -2808,6 +2814,9 @@
u8 saved_xfer_mode = ehc->saved_xfer_mode[dev->devno];
u8 saved_ncq = !!(ehc->saved_ncq_enabled & (1 << dev->devno));
+ if (!ata_dev_enabled(dev))
+ continue;
+
if (dev->xfer_mode != saved_xfer_mode ||
ata_ncq_enabled(dev) != saved_ncq)
dev->flags |= ATA_DFLAG_DUBIOUS_XFER;