USB: handle LPM errors during device suspend correctly
The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly. It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.
This patch fixes these problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index c376c8b..0416f83 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -2948,7 +2948,6 @@
{
struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent);
struct usb_port *port_dev = hub->ports[udev->portnum - 1];
- enum pm_qos_flags_status pm_qos_stat;
int port1 = udev->portnum;
int status;
bool really_suspend = true;
@@ -2966,7 +2965,7 @@
status);
/* bail if autosuspend is requested */
if (PMSG_IS_AUTO(msg))
- return status;
+ goto err_wakeup;
}
}
@@ -2975,14 +2974,16 @@
usb_set_usb2_hardware_lpm(udev, 0);
if (usb_disable_ltm(udev)) {
- dev_err(&udev->dev, "%s Failed to disable LTM before suspend\n.",
- __func__);
- return -ENOMEM;
+ dev_err(&udev->dev, "Failed to disable LTM before suspend\n.");
+ status = -ENOMEM;
+ if (PMSG_IS_AUTO(msg))
+ goto err_ltm;
}
if (usb_unlocked_disable_lpm(udev)) {
- dev_err(&udev->dev, "%s Failed to disable LPM before suspend\n.",
- __func__);
- return -ENOMEM;
+ dev_err(&udev->dev, "Failed to disable LPM before suspend\n.");
+ status = -ENOMEM;
+ if (PMSG_IS_AUTO(msg))
+ goto err_lpm3;
}
/* see 7.1.7.6 */
@@ -3010,17 +3011,19 @@
if (status) {
dev_dbg(hub->intfdev, "can't suspend port %d, status %d\n",
port1, status);
- /* paranoia: "should not happen" */
- if (udev->do_remote_wakeup)
- (void) usb_disable_remote_wakeup(udev);
+ /* Try to enable USB3 LPM and LTM again */
+ usb_unlocked_enable_lpm(udev);
+ err_lpm3:
+ usb_enable_ltm(udev);
+ err_ltm:
/* Try to enable USB2 hardware LPM again */
if (udev->usb2_hw_lpm_capable == 1)
usb_set_usb2_hardware_lpm(udev, 1);
- /* Try to enable USB3 LTM and LPM again */
- usb_enable_ltm(udev);
- usb_unlocked_enable_lpm(udev);
+ if (udev->do_remote_wakeup)
+ (void) usb_disable_remote_wakeup(udev);
+ err_wakeup:
/* System sleep transitions should never fail */
if (!PMSG_IS_AUTO(msg))
@@ -3042,14 +3045,15 @@
* Check whether current status meets the requirement of
* usb port power off mechanism
*/
- pm_qos_stat = dev_pm_qos_flags(&port_dev->dev,
- PM_QOS_FLAG_NO_POWER_OFF);
- if (!udev->do_remote_wakeup
- && pm_qos_stat != PM_QOS_FLAGS_ALL
- && udev->persist_enabled
- && !status) {
- pm_runtime_put_sync(&port_dev->dev);
- port_dev->did_runtime_put = true;
+ if (status == 0 && !udev->do_remote_wakeup && udev->persist_enabled) {
+ enum pm_qos_flags_status pm_qos_stat;
+
+ pm_qos_stat = dev_pm_qos_flags(&port_dev->dev,
+ PM_QOS_FLAG_NO_POWER_OFF);
+ if (pm_qos_stat != PM_QOS_FLAGS_ALL) {
+ pm_runtime_put_sync(&port_dev->dev);
+ port_dev->did_runtime_put = true;
+ }
}
usb_mark_last_busy(hub->hdev);