| # |
| # Multifunction miscellaneous devices |
| # |
| |
| menuconfig MFD_SUPPORT |
| bool "Multifunction device drivers" |
| depends on HAS_IOMEM |
| default y |
| help |
| Multifunction devices embed several functions (e.g. GPIOs, |
| touchscreens, keyboards, current regulators, power management chips, |
| etc...) in one single integrated circuit. They usually talk to the |
| main CPU through one or more IRQ lines and low speed data busses (SPI, |
| I2C, etc..). They appear as one single device to the main system |
| through the data bus and the MFD framework allows for sub devices |
| (a.k.a. functions) to appear as discrete platform devices. |
| MFDs are typically found on embedded platforms. |
| |
| This option alone does not add any kernel code. |
| |
| if MFD_SUPPORT |
| |
| config MFD_CORE |
| tristate |
| default n |
| |
| config MFD_88PM860X |
| bool "Support Marvell 88PM8606/88PM8607" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| This supports for Marvell 88PM8606/88PM8607 Power Management IC. |
| This includes the I2C driver and the core APIs _only_, you have to |
| select individual components like voltage regulators, RTC and |
| battery-charger under the corresponding menus. |
| |
| config MFD_SM501 |
| tristate "Support for Silicon Motion SM501" |
| ---help--- |
| This is the core driver for the Silicon Motion SM501 multimedia |
| companion chip. This device is a multifunction device which may |
| provide numerous interfaces including USB host controller, USB gadget, |
| asynchronous serial ports, audio functions, and a dual display video |
| interface. The device may be connected by PCI or local bus with |
| varying functions enabled. |
| |
| config MFD_SM501_GPIO |
| bool "Export GPIO via GPIO layer" |
| depends on MFD_SM501 && GPIOLIB |
| ---help--- |
| This option uses the gpio library layer to export the 64 GPIO |
| lines on the SM501. The platform data is used to supply the |
| base number for the first GPIO line to register. |
| |
| config MFD_ASIC3 |
| bool "Support for Compaq ASIC3" |
| depends on GENERIC_HARDIRQS && GPIOLIB && ARM |
| select MFD_CORE |
| ---help--- |
| This driver supports the ASIC3 multifunction chip found on many |
| PDAs (mainly iPAQ and HTC based ones) |
| |
| config MFD_DAVINCI_VOICECODEC |
| tristate |
| select MFD_CORE |
| |
| config MFD_DM355EVM_MSP |
| bool "DaVinci DM355 EVM microcontroller" |
| depends on I2C=y && MACH_DAVINCI_DM355_EVM |
| help |
| This driver supports the MSP430 microcontroller used on these |
| boards. MSP430 firmware manages resets and power sequencing, |
| inputs from buttons and the IR remote, LEDs, an RTC, and more. |
| |
| config MFD_TI_SSP |
| tristate "TI Sequencer Serial Port support" |
| depends on ARCH_DAVINCI_TNETV107X |
| select MFD_CORE |
| ---help--- |
| Say Y here if you want support for the Sequencer Serial Port |
| in a Texas Instruments TNETV107X SoC. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ti-ssp. |
| |
| config HTC_EGPIO |
| bool "HTC EGPIO support" |
| depends on GENERIC_HARDIRQS && GPIOLIB && ARM |
| help |
| This driver supports the CPLD egpio chip present on |
| several HTC phones. It provides basic support for input |
| pins, output pins, and irqs. |
| |
| config HTC_PASIC3 |
| tristate "HTC PASIC3 LED/DS1WM chip support" |
| select MFD_CORE |
| help |
| This core driver provides register access for the LED/DS1WM |
| chips labeled "AIC2" and "AIC3", found on HTC Blueangel and |
| HTC Magician devices, respectively. Actual functionality is |
| handled by the leds-pasic3 and ds1wm drivers. |
| |
| config HTC_I2CPLD |
| bool "HTC I2C PLD chip support" |
| depends on I2C=y && GPIOLIB |
| help |
| If you say yes here you get support for the supposed CPLD |
| found on omap850 HTC devices like the HTC Wizard and HTC Herald. |
| This device provides input and output GPIOs through an I2C |
| interface to one or more sub-chips. |
| |
| config UCB1400_CORE |
| tristate "Philips UCB1400 Core driver" |
| depends on AC97_BUS |
| depends on GPIOLIB |
| help |
| This enables support for the Philips UCB1400 core functions. |
| The UCB1400 is an AC97 audio codec. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ucb1400_core. |
| |
| config TPS6105X |
| tristate "TPS61050/61052 Boost Converters" |
| depends on I2C |
| select REGULATOR |
| select MFD_CORE |
| select REGULATOR_FIXED_VOLTAGE |
| help |
| This option enables a driver for the TP61050/TPS61052 |
| high-power "white LED driver". This boost converter is |
| sometimes used for other things than white LEDs, and |
| also contains a GPIO pin. |
| |
| config TPS65010 |
| tristate "TPS6501x Power Management chips" |
| depends on I2C && GPIOLIB |
| default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK |
| help |
| If you say yes here you get support for the TPS6501x series of |
| Power Management chips. These include voltage regulators, |
| lithium ion/polymer battery charging, and other features that |
| are often used in portable devices like cell phones and cameras. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps65010. |
| |
| config TPS6507X |
| tristate "TPS6507x Power Management / Touch Screen chips" |
| select MFD_CORE |
| depends on I2C |
| help |
| If you say yes here you get support for the TPS6507x series of |
| Power Management / Touch Screen chips. These include voltage |
| regulators, lithium ion/polymer battery charging, touch screen |
| and other features that are often used in portable devices. |
| This driver can also be built as a module. If so, the module |
| will be called tps6507x. |
| |
| config MFD_TPS6586X |
| bool "TPS6586x Power Management chips" |
| depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| If you say yes here you get support for the TPS6586X series of |
| Power Management chips. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps6586x. |
| |
| config MFD_TPS65910 |
| bool "TPS65910 Power Management chip" |
| depends on I2C=y && GPIOLIB |
| select MFD_CORE |
| select GPIO_TPS65910 |
| help |
| if you say yes here you get support for the TPS65910 series of |
| Power Management chips. |
| |
| config MFD_TPS65912 |
| bool |
| depends on GPIOLIB |
| |
| config MFD_TPS65912_I2C |
| bool "TPS95612 Power Management chip with I2C" |
| select MFD_CORE |
| select MFD_TPS65912 |
| depends on I2C=y && GPIOLIB |
| help |
| If you say yes here you get support for the TPS65912 series of |
| PM chips with I2C interface. |
| |
| config MFD_TPS65912_SPI |
| bool "TPS65912 Power Management chip with SPI" |
| select MFD_CORE |
| select MFD_TPS65912 |
| depends on SPI_MASTER && GPIOLIB |
| help |
| If you say yes here you get support for the TPS65912 series of |
| PM chips with SPI interface. |
| |
| config MENELAUS |
| bool "Texas Instruments TWL92330/Menelaus PM chip" |
| depends on I2C=y && ARCH_OMAP2 |
| help |
| If you say yes here you get support for the Texas Instruments |
| TWL92330/Menelaus Power Management chip. This include voltage |
| regulators, Dual slot memory card transceivers, real-time clock |
| and other features that are often used in portable devices like |
| cell phones and PDAs. |
| |
| config TWL4030_CORE |
| bool "Texas Instruments TWL4030/TWL5030/TWL6030/TPS659x0 Support" |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| Say yes here if you have TWL4030 / TWL6030 family chip on your board. |
| This core driver provides register access and IRQ handling |
| facilities, and registers devices for the various functions |
| so that function-specific drivers can bind to them. |
| |
| These multi-function chips are found on many OMAP2 and OMAP3 |
| boards, providing power management, RTC, GPIO, keypad, a |
| high speed USB OTG transceiver, an audio codec (on most |
| versions) and many other features. |
| |
| config TWL4030_MADC |
| tristate "Texas Instruments TWL4030 MADC" |
| depends on TWL4030_CORE |
| help |
| This driver provides support for triton TWL4030-MADC. The |
| driver supports both RT and SW conversion methods. |
| |
| This driver can be built as a module. If so it will be |
| named twl4030-madc |
| |
| config TWL4030_POWER |
| bool "Support power resources on TWL4030 family chips" |
| depends on TWL4030_CORE && ARM |
| help |
| Say yes here if you want to use the power resources on the |
| TWL4030 family chips. Most of these resources are regulators, |
| which have a separate driver; some are control signals, such |
| as clock request handshaking. |
| |
| This driver uses board-specific data to initialize the resources |
| and load scripts controlling which resources are switched off/on |
| or reset when a sleep, wakeup or warm reset event occurs. |
| |
| config MFD_TWL4030_AUDIO |
| bool |
| depends on TWL4030_CORE |
| select MFD_CORE |
| default n |
| |
| config TWL6030_PWM |
| tristate "TWL6030 PWM (Pulse Width Modulator) Support" |
| depends on TWL4030_CORE |
| select HAVE_PWM |
| default n |
| help |
| Say yes here if you want support for TWL6030 PWM. |
| This is used to control charging LED brightness. |
| |
| config TWL6040_CORE |
| bool |
| depends on TWL4030_CORE && GENERIC_HARDIRQS |
| select MFD_CORE |
| default n |
| |
| config MFD_STMPE |
| bool "Support STMicroelectronics STMPE" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Support for the STMPE family of I/O Expanders from |
| STMicroelectronics. |
| |
| Currently supported devices are: |
| |
| STMPE811: GPIO, Touchscreen |
| STMPE1601: GPIO, Keypad |
| STMPE2401: GPIO, Keypad |
| STMPE2403: GPIO, Keypad |
| |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the functionality |
| of the device. Currently available sub drivers are: |
| |
| GPIO: stmpe-gpio |
| Keypad: stmpe-keypad |
| Touchscreen: stmpe-ts |
| |
| config MFD_TC3589X |
| bool "Support Toshiba TC35892 and variants" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Support for the Toshiba TC35892 and variants I/O Expander. |
| |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_TMIO |
| bool |
| default n |
| |
| config MFD_T7L66XB |
| bool "Support Toshiba T7L66XB" |
| depends on ARM && HAVE_CLK |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller T7L66XB |
| |
| config MFD_TC6387XB |
| bool "Support Toshiba TC6387XB" |
| depends on ARM && HAVE_CLK |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller TC6387XB |
| |
| config MFD_TC6393XB |
| bool "Support Toshiba TC6393XB" |
| depends on GPIOLIB && ARM |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller TC6393XB |
| |
| config PMIC_DA903X |
| bool "Dialog Semiconductor DA9030/DA9034 PMIC Support" |
| depends on I2C=y |
| help |
| Say yes here to support for Dialog Semiconductor DA9030 (a.k.a |
| ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC |
| usually found on PXA processors-based platforms. This includes |
| the I2C driver and the core APIs _only_, you have to select |
| individual components like LCD backlight, voltage regulators, |
| LEDs and battery-charger under the corresponding menus. |
| |
| config PMIC_ADP5520 |
| bool "Analog Devices ADP5520/01 MFD PMIC Core Support" |
| depends on I2C=y |
| help |
| Say yes here to add support for Analog Devices AD5520 and ADP5501, |
| Multifunction Power Management IC. This includes |
| the I2C driver and the core APIs _only_, you have to select |
| individual components like LCD backlight, LEDs, GPIOs and Kepad |
| under the corresponding menus. |
| |
| config MFD_MAX8925 |
| bool "Maxim Semiconductor MAX8925 PMIC Support" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Say yes here to support for Maxim Semiconductor MAX8925. This is |
| a Power Management IC. This driver provies common support for |
| accessing the device, additional drivers must be enabled in order |
| to use the functionality of the device. |
| |
| config MFD_MAX8997 |
| bool "Maxim Semiconductor MAX8997/8966 PMIC Support" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Say yes here to support for Maxim Semiconductor MAX8998/8966. |
| This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic, |
| MUIC controls on chip. |
| This driver provides common support for accessing the device; |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_MAX8998 |
| bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Say yes here to support for Maxim Semiconductor MAX8998 and |
| National Semiconductor LP3974. This is a Power Management IC. |
| This driver provies common support for accessing the device, |
| additional drivers must be enabled in order to use the functionality |
| of the device. |
| |
| config MFD_WM8400 |
| tristate "Support Wolfson Microelectronics WM8400" |
| select MFD_CORE |
| depends on I2C |
| help |
| Support for the Wolfson Microelecronics WM8400 PMIC and audio |
| CODEC. This driver provides common support for accessing |
| the device, additional drivers must be enabled in order to use |
| the functionality of the device. |
| |
| config MFD_WM831X |
| bool |
| depends on GENERIC_HARDIRQS |
| |
| config MFD_WM831X_I2C |
| bool "Support Wolfson Microelectronics WM831x/2x PMICs with I2C" |
| select MFD_CORE |
| select MFD_WM831X |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| Support for the Wolfson Microelecronics WM831x and WM832x PMICs |
| when controlled using I2C. This driver provides common support |
| for accessing the device, additional drivers must be enabled in |
| order to use the functionality of the device. |
| |
| config MFD_WM831X_SPI |
| bool "Support Wolfson Microelectronics WM831x/2x PMICs with SPI" |
| select MFD_CORE |
| select MFD_WM831X |
| depends on SPI_MASTER && GENERIC_HARDIRQS |
| help |
| Support for the Wolfson Microelecronics WM831x and WM832x PMICs |
| when controlled using SPI. This driver provides common support |
| for accessing the device, additional drivers must be enabled in |
| order to use the functionality of the device. |
| |
| config MFD_WM8350 |
| bool |
| depends on GENERIC_HARDIRQS |
| |
| config MFD_WM8350_CONFIG_MODE_0 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_CONFIG_MODE_1 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_CONFIG_MODE_2 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_CONFIG_MODE_3 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_0 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_1 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_2 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_3 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_0 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_1 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_2 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_3 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_I2C |
| bool "Support Wolfson Microelectronics WM8350 with I2C" |
| select MFD_WM8350 |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| The WM8350 is an integrated audio and power management |
| subsystem with watchdog and RTC functionality for embedded |
| systems. This option enables core support for the WM8350 with |
| I2C as the control interface. Additional options must be |
| selected to enable support for the functionality of the chip. |
| |
| config MFD_WM8994 |
| bool "Support Wolfson Microelectronics WM8994" |
| select MFD_CORE |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| The WM8994 is a highly integrated hi-fi CODEC designed for |
| smartphone applicatiosn. As well as audio functionality it |
| has on board GPIO and regulator functionality which is |
| supported via the relevant subsystems. This driver provides |
| core support for the WM8994, in order to use the actual |
| functionaltiy of the device other drivers must be enabled. |
| |
| config MFD_PCF50633 |
| tristate "Support for NXP PCF50633" |
| depends on I2C |
| help |
| Say yes here if you have NXP PCF50633 chip on your board. |
| This core driver provides register access and IRQ handling |
| facilities, and registers devices for the various functions |
| so that function-specific drivers can bind to them. |
| |
| config PCF50633_ADC |
| tristate "Support for NXP PCF50633 ADC" |
| depends on MFD_PCF50633 |
| help |
| Say yes here if you want to include support for ADC in the |
| NXP PCF50633 chip. |
| |
| config PCF50633_GPIO |
| tristate "Support for NXP PCF50633 GPIO" |
| depends on MFD_PCF50633 |
| help |
| Say yes here if you want to include support GPIO for pins on |
| the PCF50633 chip. |
| |
| config MFD_MC13783 |
| tristate |
| |
| config MFD_MC13XXX |
| tristate "Support Freescale MC13783 and MC13892" |
| depends on SPI_MASTER |
| select MFD_CORE |
| select MFD_MC13783 |
| help |
| Support for the Freescale (Atlas) PMIC and audio CODECs |
| MC13783 and MC13892. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config ABX500_CORE |
| bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions" |
| default y if ARCH_U300 || ARCH_U8500 |
| help |
| Say yes here if you have the ABX500 Mixed Signal IC family |
| chips. This core driver expose register access functions. |
| Functionality specific drivers using these functions can |
| remain unchanged when IC changes. Binding of the functions to |
| actual register access is done by the IC core driver. |
| |
| config AB3100_CORE |
| bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions" |
| depends on I2C=y && ABX500_CORE |
| select MFD_CORE |
| default y if ARCH_U300 |
| help |
| Select this to enable the AB3100 Mixed Signal IC core |
| functionality. This connects to a AB3100 on the I2C bus |
| and expose a number of symbols needed for dependent devices |
| to read and write registers and subscribe to events from |
| this multi-functional IC. This is needed to use other features |
| of the AB3100 such as battery-backed RTC, charging control, |
| LEDs, vibrator, system power and temperature, power management |
| and ALSA sound. |
| |
| config AB3100_OTP |
| tristate "ST-Ericsson AB3100 OTP functions" |
| depends on AB3100_CORE |
| default y if AB3100_CORE |
| help |
| Select this to enable the AB3100 Mixed Signal IC OTP (one-time |
| programmable memory) support. This exposes a sysfs file to read |
| out OTP values. |
| |
| config EZX_PCAP |
| bool "PCAP Support" |
| depends on GENERIC_HARDIRQS && SPI_MASTER |
| help |
| This enables the PCAP ASIC present on EZX Phones. This is |
| needed for MMC, TouchScreen, Sound, USB, etc.. |
| |
| config AB8500_CORE |
| bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" |
| depends on GENERIC_HARDIRQS && ABX500_CORE |
| select MFD_CORE |
| help |
| Select this option to enable access to AB8500 power management |
| chip. This connects to U8500 either on the SSP/SPI bus (deprecated |
| since hardware version v1.0) or the I2C bus via PRCMU. It also adds |
| the irq_chip parts for handling the Mixed Signal chip events. |
| This chip embeds various other multimedia funtionalities as well. |
| |
| config AB8500_I2C_CORE |
| bool "AB8500 register access via PRCMU I2C" |
| depends on AB8500_CORE && MFD_DB8500_PRCMU |
| default y |
| help |
| This enables register access to the AB8500 chip via PRCMU I2C. |
| The AB8500 chip can be accessed via SPI or I2C. On DB8500 hardware |
| the I2C bus is connected to the Power Reset |
| and Mangagement Unit, PRCMU. |
| |
| config AB8500_DEBUG |
| bool "Enable debug info via debugfs" |
| depends on AB8500_CORE && DEBUG_FS |
| default y if DEBUG_FS |
| help |
| Select this option if you want debug information using the debug |
| filesystem, debugfs. |
| |
| config AB8500_GPADC |
| bool "AB8500 GPADC driver" |
| depends on AB8500_CORE && REGULATOR_AB8500 |
| default y |
| help |
| AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage |
| |
| config AB3550_CORE |
| bool "ST-Ericsson AB3550 Mixed Signal Circuit core functions" |
| select MFD_CORE |
| depends on I2C=y && GENERIC_HARDIRQS && ABX500_CORE |
| help |
| Select this to enable the AB3550 Mixed Signal IC core |
| functionality. This connects to a AB3550 on the I2C bus |
| and expose a number of symbols needed for dependent devices |
| to read and write registers and subscribe to events from |
| this multi-functional IC. This is needed to use other features |
| of the AB3550 such as battery-backed RTC, charging control, |
| LEDs, vibrator, system power and temperature, power management |
| and ALSA sound. |
| |
| config MFD_DB8500_PRCMU |
| bool "ST-Ericsson DB8500 Power Reset Control Management Unit" |
| depends on UX500_SOC_DB8500 |
| select MFD_CORE |
| help |
| Select this option to enable support for the DB8500 Power Reset |
| and Control Management Unit. This is basically an autonomous |
| system controller running an XP70 microprocessor, which is accessed |
| through a register map. |
| |
| config MFD_DB5500_PRCMU |
| bool "ST-Ericsson DB5500 Power Reset Control Management Unit" |
| depends on UX500_SOC_DB5500 |
| select MFD_CORE |
| help |
| Select this option to enable support for the DB5500 Power Reset |
| and Control Management Unit. This is basically an autonomous |
| system controller running an XP70 microprocessor, which is accessed |
| through a register map. |
| |
| config MFD_CS5535 |
| tristate "Support for CS5535 and CS5536 southbridge core functions" |
| select MFD_CORE |
| depends on PCI && X86 |
| ---help--- |
| This is the core driver for CS5535/CS5536 MFD functions. This is |
| necessary for using the board's GPIO and MFGPT functionality. |
| |
| config MFD_TIMBERDALE |
| tristate "Support for the Timberdale FPGA" |
| select MFD_CORE |
| depends on PCI && GPIOLIB |
| ---help--- |
| This is the core driver for the timberdale FPGA. This device is a |
| multifunction device which exposes numerous platform devices. |
| |
| The timberdale FPGA can be found on the Intel Atom development board |
| for in-vehicle infontainment, called Russellville. |
| |
| config LPC_SCH |
| tristate "Intel SCH LPC" |
| depends on PCI |
| select MFD_CORE |
| help |
| LPC bridge function of the Intel SCH provides support for |
| System Management Bus and General Purpose I/O. |
| |
| config MFD_RDC321X |
| tristate "Support for RDC-R321x southbridge" |
| select MFD_CORE |
| depends on PCI |
| help |
| Say yes here if you want to have support for the RDC R-321x SoC |
| southbridge which provides access to GPIOs and Watchdog using the |
| southbridge PCI device configuration space. |
| |
| config MFD_JANZ_CMODIO |
| tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board" |
| select MFD_CORE |
| depends on PCI |
| help |
| This is the core driver for the Janz CMOD-IO PCI MODULbus |
| carrier board. This device is a PCI to MODULbus bridge which may |
| host many different types of MODULbus daughterboards, including |
| CAN and GPIO controllers. |
| |
| config MFD_JZ4740_ADC |
| bool "Support for the JZ4740 SoC ADC core" |
| select MFD_CORE |
| select GENERIC_IRQ_CHIP |
| depends on MACH_JZ4740 |
| help |
| Say yes here if you want support for the ADC unit in the JZ4740 SoC. |
| This driver is necessary for jz4740-battery and jz4740-hwmon driver. |
| |
| config MFD_VX855 |
| tristate "Support for VIA VX855/VX875 integrated south bridge" |
| depends on PCI |
| select MFD_CORE |
| help |
| Say yes here to enable support for various functions of the |
| VIA VX855/VX875 south bridge. You will need to enable the vx855_spi |
| and/or vx855_gpio drivers for this to do anything useful. |
| |
| config MFD_WL1273_CORE |
| tristate "Support for TI WL1273 FM radio." |
| depends on I2C |
| select MFD_CORE |
| default n |
| help |
| This is the core driver for the TI WL1273 FM radio. This MFD |
| driver connects the radio-wl1273 V4L2 module and the wl1273 |
| audio codec. |
| |
| config MFD_OMAP_USB_HOST |
| bool "Support OMAP USBHS core driver" |
| depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 |
| default y |
| help |
| This is the core driver for the OAMP EHCI and OHCI drivers. |
| This MFD driver does the required setup functionalities for |
| OMAP USB Host drivers. |
| |
| config MFD_PM8XXX |
| tristate |
| |
| config MFD_PM8921_CORE |
| tristate "Qualcomm PM8921 PMIC chip" |
| depends on MSM_SSBI |
| select MFD_CORE |
| select MFD_PM8XXX |
| help |
| If you say yes to this option, support will be included for the |
| built-in PM8921 PMIC chip. |
| |
| This is required if your board has a PM8921 and uses its features, |
| such as: MPPs, GPIOs, regulators, interrupts, and PWM. |
| |
| Say M here if you want to include support for PM8921 chip as a module. |
| This will build a module called "pm8921-core". |
| |
| config MFD_PM8XXX_IRQ |
| bool "Support for Qualcomm PM8xxx IRQ features" |
| depends on MFD_PM8XXX |
| default y if MFD_PM8XXX |
| help |
| This is the IRQ driver for Qualcomm PM 8xxx PMIC chips. |
| |
| This is required to use certain other PM 8xxx features, such as GPIO |
| and MPP. |
| |
| config TPS65911_COMPARATOR |
| tristate |
| |
| endif # MFD_SUPPORT |
| |
| menu "Multimedia Capabilities Port drivers" |
| depends on ARCH_SA1100 |
| |
| config MCP |
| tristate |
| |
| # Interface drivers |
| config MCP_SA11X0 |
| tristate "Support SA11x0 MCP interface" |
| depends on ARCH_SA1100 |
| select MCP |
| |
| # Chip drivers |
| config MCP_UCB1200 |
| tristate "Support for UCB1200 / UCB1300" |
| depends on MCP |
| |
| config MCP_UCB1200_TS |
| tristate "Touchscreen interface support" |
| depends on MCP_UCB1200 && INPUT |
| |
| endmenu |