igc: Add code for PHY support
Add PHY's ID support
Add support for initialization, acquire and release of PHY
Enable register access
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/intel/igc/igc_base.c b/drivers/net/ethernet/intel/igc/igc_base.c
index 2d49814..55faef9 100644
--- a/drivers/net/ethernet/intel/igc/igc_base.c
+++ b/drivers/net/ethernet/intel/igc/igc_base.c
@@ -124,6 +124,22 @@ static s32 igc_reset_hw_base(struct igc_hw *hw)
}
/**
+ * igc_get_phy_id_base - Retrieve PHY addr and id
+ * @hw: pointer to the HW structure
+ *
+ * Retrieves the PHY address and ID for both PHY's which do and do not use
+ * sgmi interface.
+ */
+static s32 igc_get_phy_id_base(struct igc_hw *hw)
+{
+ s32 ret_val = 0;
+
+ ret_val = igc_get_phy_id(hw);
+
+ return ret_val;
+}
+
+/**
* igc_init_nvm_params_base - Init NVM func ptrs.
* @hw: pointer to the HW structure
*/
@@ -187,6 +203,59 @@ static s32 igc_init_mac_params_base(struct igc_hw *hw)
return 0;
}
+/**
+ * igc_init_phy_params_base - Init PHY func ptrs.
+ * @hw: pointer to the HW structure
+ */
+static s32 igc_init_phy_params_base(struct igc_hw *hw)
+{
+ struct igc_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u32 ctrl_ext;
+
+ if (hw->phy.media_type != igc_media_type_copper) {
+ phy->type = igc_phy_none;
+ goto out;
+ }
+
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
+ phy->reset_delay_us = 100;
+
+ ctrl_ext = rd32(IGC_CTRL_EXT);
+
+ /* set lan id */
+ hw->bus.func = (rd32(IGC_STATUS) & IGC_STATUS_FUNC_MASK) >>
+ IGC_STATUS_FUNC_SHIFT;
+
+ /* Make sure the PHY is in a good state. Several people have reported
+ * firmware leaving the PHY's page select register set to something
+ * other than the default of zero, which causes the PHY ID read to
+ * access something other than the intended register.
+ */
+ ret_val = hw->phy.ops.reset(hw);
+ if (ret_val) {
+ hw_dbg("Error resetting the PHY.\n");
+ goto out;
+ }
+
+ ret_val = igc_get_phy_id_base(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Verify phy id and set remaining function pointers */
+ switch (phy->id) {
+ case I225_I_PHY_ID:
+ phy->type = igc_phy_i225;
+ break;
+ default:
+ ret_val = -IGC_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
static s32 igc_get_invariants_base(struct igc_hw *hw)
{
u32 link_mode = 0;
@@ -211,6 +280,8 @@ static s32 igc_get_invariants_base(struct igc_hw *hw)
break;
}
+ /* setup PHY parameters */
+ ret_val = igc_init_phy_params_base(hw);
if (ret_val)
goto out;
@@ -219,6 +290,34 @@ static s32 igc_get_invariants_base(struct igc_hw *hw)
}
/**
+ * igc_acquire_phy_base - Acquire rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * Acquire access rights to the correct PHY. This is a
+ * function pointer entry point called by the api module.
+ */
+static s32 igc_acquire_phy_base(struct igc_hw *hw)
+{
+ u16 mask = IGC_SWFW_PHY0_SM;
+
+ return hw->mac.ops.acquire_swfw_sync(hw, mask);
+}
+
+/**
+ * igc_release_phy_base - Release rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to release access rights to the correct PHY. This is a
+ * function pointer entry point called by the api module.
+ */
+static void igc_release_phy_base(struct igc_hw *hw)
+{
+ u16 mask = IGC_SWFW_PHY0_SM;
+
+ hw->mac.ops.release_swfw_sync(hw, mask);
+}
+
+/**
* igc_get_link_up_info_base - Get link speed/duplex info
* @hw: pointer to the HW structure
* @speed: stores the current speed
@@ -290,6 +389,20 @@ static s32 igc_read_mac_addr_base(struct igc_hw *hw)
}
/**
+ * igc_power_down_phy_copper_base - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ */
+void igc_power_down_phy_copper_base(struct igc_hw *hw)
+{
+ /* If the management interface is not enabled, then power down */
+ if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
+ igc_power_down_phy_copper(hw);
+}
+
+/**
* igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
* @hw: pointer to the HW structure
*
@@ -373,7 +486,16 @@ static struct igc_mac_operations igc_mac_ops_base = {
.get_speed_and_duplex = igc_get_link_up_info_base,
};
+static const struct igc_phy_operations igc_phy_ops_base = {
+ .acquire = igc_acquire_phy_base,
+ .release = igc_release_phy_base,
+ .reset = igc_phy_hw_reset,
+ .read_reg = igc_read_phy_reg_gpy,
+ .write_reg = igc_write_phy_reg_gpy,
+};
+
const struct igc_info igc_base_info = {
.get_invariants = igc_get_invariants_base,
.mac_ops = &igc_mac_ops_base,
+ .phy_ops = &igc_phy_ops_base,
};