libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
index 701d0ad..2b9da71 100644
--- a/drivers/ata/pata_scc.c
+++ b/drivers/ata/pata_scc.c
@@ -441,7 +441,7 @@
out_be32(mmio + SCC_DMA_CMD, dmactl);
/* issue r/w command */
- ap->ops->exec_command(ap, &qc->tf);
+ ap->ops->sff_exec_command(ap, &qc->tf);
}
/**
@@ -476,7 +476,7 @@
struct ata_ioports *ioaddr = &ap->ioaddr;
u8 nsect, lbal;
- ap->ops->dev_select(ap, device);
+ ap->ops->sff_dev_select(ap, device);
out_be32(ioaddr->nsect_addr, 0x55);
out_be32(ioaddr->lbal_addr, 0xaa);
@@ -525,7 +525,7 @@
while (dev1) {
u8 nsect, lbal;
- ap->ops->dev_select(ap, 1);
+ ap->ops->sff_dev_select(ap, 1);
nsect = in_be32(ioaddr->nsect_addr);
lbal = in_be32(ioaddr->lbal_addr);
if ((nsect == 1) && (lbal == 1))
@@ -541,11 +541,11 @@
}
/* is all this really necessary? */
- ap->ops->dev_select(ap, 0);
+ ap->ops->sff_dev_select(ap, 0);
if (dev1)
- ap->ops->dev_select(ap, 1);
+ ap->ops->sff_dev_select(ap, 1);
if (dev0)
- ap->ops->dev_select(ap, 0);
+ ap->ops->sff_dev_select(ap, 0);
return 0;
}
@@ -616,7 +616,7 @@
devmask |= (1 << 1);
/* select device 0 again */
- ap->ops->dev_select(ap, 0);
+ ap->ops->sff_dev_select(ap, 0);
/* issue bus reset */
DPRINTK("about to softreset, devmask=%x\n", devmask);
@@ -829,7 +829,7 @@
out_be32(ioaddr->ctl_addr, ap->ctl);
tmp = ata_wait_idle(ap);
- ap->ops->irq_clear(ap);
+ ap->ops->sff_irq_clear(ap);
return tmp;
}
@@ -854,9 +854,9 @@
* ATA_NIEN manipulation. Also, many controllers fail to mask
* previously pending IRQ on ATA_NIEN assertion. Clear it.
*/
- ap->ops->check_status(ap);
+ ap->ops->sff_check_status(ap);
- ap->ops->irq_clear(ap);
+ ap->ops->sff_irq_clear(ap);
}
/**
@@ -887,9 +887,9 @@
/* is double-select really necessary? */
if (classes[0] != ATA_DEV_NONE)
- ap->ops->dev_select(ap, 1);
+ ap->ops->sff_dev_select(ap, 1);
if (classes[1] != ATA_DEV_NONE)
- ap->ops->dev_select(ap, 0);
+ ap->ops->sff_dev_select(ap, 0);
/* bail out if no device is present */
if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
@@ -967,18 +967,18 @@
.set_dmamode = scc_set_dmamode,
.mode_filter = scc_mode_filter,
- .tf_load = scc_tf_load,
- .tf_read = scc_tf_read,
- .exec_command = scc_exec_command,
- .check_status = scc_check_status,
- .check_altstatus = scc_check_altstatus,
- .dev_select = scc_dev_select,
+ .sff_tf_load = scc_tf_load,
+ .sff_tf_read = scc_tf_read,
+ .sff_exec_command = scc_exec_command,
+ .sff_check_status = scc_check_status,
+ .sff_check_altstatus = scc_check_altstatus,
+ .sff_dev_select = scc_dev_select,
.bmdma_setup = scc_bmdma_setup,
.bmdma_start = scc_bmdma_start,
.bmdma_stop = scc_bmdma_stop,
.bmdma_status = scc_bmdma_status,
- .data_xfer = scc_data_xfer,
+ .sff_data_xfer = scc_data_xfer,
.freeze = scc_freeze,
.prereset = scc_pata_prereset,
@@ -986,8 +986,8 @@
.postreset = scc_postreset,
.post_internal_cmd = scc_bmdma_stop,
- .irq_clear = scc_irq_clear,
- .irq_on = scc_irq_on,
+ .sff_irq_clear = scc_irq_clear,
+ .sff_irq_on = scc_irq_on,
.port_start = scc_port_start,
.port_stop = scc_port_stop,