OMAP3 SDRC: add support for 2 SDRAM chip selects
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index f41f8d9..3aef744 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -36,7 +36,7 @@
.text
-/* r4 parameters */
+/* r1 parameters */
#define SDRC_NO_UNLOCK_DLL 0x0
#define SDRC_UNLOCK_DLL 0x1
@@ -71,40 +71,71 @@
/*
* omap3_sram_configure_core_dpll - change DPLL3 M2 divider
- * r0 = new SDRC_RFR_CTRL register contents
- * r1 = new SDRC_ACTIM_CTRLA register contents
- * r2 = new SDRC_ACTIM_CTRLB register contents
- * r3 = new M2 divider setting (only 1 and 2 supported right now)
- * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
- * SDRC rates < 83MHz
- * r5 = number of MPU cycles to wait for SDRC to stabilize after
- * reprogramming the SDRC when switching to a slower MPU speed
- * r6 = new SDRC_MR_0 register value
- * r7 = increasing SDRC rate? (1 = yes, 0 = no)
*
+ * Params passed in registers:
+ * r0 = new M2 divider setting (only 1 and 2 supported right now)
+ * r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
+ * SDRC rates < 83MHz
+ * r2 = number of MPU cycles to wait for SDRC to stabilize after
+ * reprogramming the SDRC when switching to a slower MPU speed
+ * r3 = increasing SDRC rate? (1 = yes, 0 = no)
+ *
+ * Params passed via the stack. The needed params will be copied in SRAM
+ * before use by the code in SRAM (SDRAM is not accessible during SDRC
+ * reconfiguration):
+ * new SDRC_RFR_CTRL_0 register contents
+ * new SDRC_ACTIM_CTRL_A_0 register contents
+ * new SDRC_ACTIM_CTRL_B_0 register contents
+ * new SDRC_MR_0 register value
+ * new SDRC_RFR_CTRL_1 register contents
+ * new SDRC_ACTIM_CTRL_A_1 register contents
+ * new SDRC_ACTIM_CTRL_B_1 register contents
+ * new SDRC_MR_1 register value
+ *
+ * If the param SDRC_RFR_CTRL_1 is 0, the parameters
+ * are not programmed into the SDRC CS1 registers
*/
ENTRY(omap3_sram_configure_core_dpll)
stmfd sp!, {r1-r12, lr} @ store regs to stack
- ldr r4, [sp, #52] @ pull extra args off the stack
- ldr r5, [sp, #56] @ load extra args from the stack
- ldr r6, [sp, #60] @ load extra args from the stack
- ldr r7, [sp, #64] @ load extra args from the stack
+
+ @ pull the extra args off the stack
+ @ and store them in SRAM
+ ldr r4, [sp, #52]
+ str r4, omap_sdrc_rfr_ctrl_0_val
+ ldr r4, [sp, #56]
+ str r4, omap_sdrc_actim_ctrl_a_0_val
+ ldr r4, [sp, #60]
+ str r4, omap_sdrc_actim_ctrl_b_0_val
+ ldr r4, [sp, #64]
+ str r4, omap_sdrc_mr_0_val
+ ldr r4, [sp, #68]
+ str r4, omap_sdrc_rfr_ctrl_1_val
+ cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0,
+ beq skip_cs1_params @ do not use cs1 params
+ ldr r4, [sp, #72]
+ str r4, omap_sdrc_actim_ctrl_a_1_val
+ ldr r4, [sp, #76]
+ str r4, omap_sdrc_actim_ctrl_b_1_val
+ ldr r4, [sp, #80]
+ str r4, omap_sdrc_mr_1_val
+skip_cs1_params:
dsb @ flush buffered writes to interconnect
- cmp r7, #1 @ if increasing SDRC clk rate,
+
+ cmp r3, #1 @ if increasing SDRC clk rate,
bleq configure_sdrc @ program the SDRC regs early (for RFR)
- cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state
+ cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state
bleq unlock_dll
blne lock_dll
bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC
bl configure_core_dpll @ change the DPLL3 M2 divider
bl enable_sdrc @ take SDRC out of idle
- cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change
+ cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change
bleq wait_dll_unlock
blne wait_dll_lock
- cmp r7, #1 @ if increasing SDRC clk rate,
+ cmp r3, #1 @ if increasing SDRC clk rate,
beq return_to_sdram @ return to SDRAM code, otherwise,
bl configure_sdrc @ reprogram SDRC regs now
- mov r12, r5
+ mov r12, r2
bl wait_clk_stable @ wait for SDRC to stabilize
return_to_sdram:
isb @ prevent speculative exec past here
@@ -149,7 +180,7 @@
ldr r12, [r11]
ldr r10, core_m2_mask_val @ modify m2 for core dpll
and r12, r12, r10
- orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
+ orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
str r12, [r11]
ldr r12, [r11] @ posted-write barrier for CM
bx lr
@@ -187,15 +218,34 @@
bne wait_dll_unlock
bx lr
configure_sdrc:
- ldr r11, omap3_sdrc_rfr_ctrl
- str r0, [r11]
- ldr r11, omap3_sdrc_actim_ctrla
- str r1, [r11]
- ldr r11, omap3_sdrc_actim_ctrlb
- str r2, [r11]
+ ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM
+ ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM
+ str r12, [r11] @ store
+ ldr r12, omap_sdrc_actim_ctrl_a_0_val
+ ldr r11, omap3_sdrc_actim_ctrl_a_0
+ str r12, [r11]
+ ldr r12, omap_sdrc_actim_ctrl_b_0_val
+ ldr r11, omap3_sdrc_actim_ctrl_b_0
+ str r12, [r11]
+ ldr r12, omap_sdrc_mr_0_val
ldr r11, omap3_sdrc_mr_0
- str r6, [r11]
- ldr r6, [r11] @ posted-write barrier for SDRC
+ str r12, [r11]
+ ldr r12, omap_sdrc_rfr_ctrl_1_val
+ cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0,
+ beq skip_cs1_prog @ do not program cs1 params
+ ldr r11, omap3_sdrc_rfr_ctrl_1
+ str r12, [r11]
+ ldr r12, omap_sdrc_actim_ctrl_a_1_val
+ ldr r11, omap3_sdrc_actim_ctrl_a_1
+ str r12, [r11]
+ ldr r12, omap_sdrc_actim_ctrl_b_1_val
+ ldr r11, omap3_sdrc_actim_ctrl_b_1
+ str r12, [r11]
+ ldr r12, omap_sdrc_mr_1_val
+ ldr r11, omap3_sdrc_mr_1
+ str r12, [r11]
+skip_cs1_prog:
+ ldr r12, [r11] @ posted-write barrier for SDRC
bx lr
omap3_sdrc_power:
@@ -206,14 +256,40 @@
.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST)
omap3_cm_iclken1_core:
.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1)
-omap3_sdrc_rfr_ctrl:
+
+omap3_sdrc_rfr_ctrl_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-omap3_sdrc_actim_ctrla:
+omap3_sdrc_rfr_ctrl_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1)
+omap3_sdrc_actim_ctrl_a_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
-omap3_sdrc_actim_ctrlb:
+omap3_sdrc_actim_ctrl_a_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1)
+omap3_sdrc_actim_ctrl_b_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
+omap3_sdrc_actim_ctrl_b_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1)
omap3_sdrc_mr_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
+omap3_sdrc_mr_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_MR_1)
+omap_sdrc_rfr_ctrl_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_rfr_ctrl_1_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_1_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_1_val:
+ .word 0xDEADBEEF
+omap_sdrc_mr_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_mr_1_val:
+ .word 0xDEADBEEF
+
omap3_sdrc_dlla_status:
.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
omap3_sdrc_dlla_ctrl:
@@ -223,3 +299,4 @@
ENTRY(omap3_sram_configure_core_dpll_sz)
.word . - omap3_sram_configure_core_dpll
+