diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index c7e3596..ddf2cc5 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -89,12 +89,6 @@
 	  Select SystemH if you are configuring for a Renesas SystemH
 	  7751R evaluation board.
 
-config SH_STB1_HARP
-	bool "STB1_Harp"
-
-config SH_STB1_OVERDRIVE
-	bool "STB1_Overdrive"
-
 config SH_HP6XX
 	bool "HP6XX"
 	help
@@ -102,19 +96,6 @@
 	  More information (hardware only) at
 	  <http://www.hp.com/jornada/>.
 
-config SH_CQREEK
-	bool "CqREEK"
-	help
-	  Select CqREEK if configuring for a CqREEK SH7708 or SH7750.
-	  More information at
-	  <http://sources.redhat.com/ecos/hardware.html#SuperH>.
-
-config SH_DMIDA
-	bool "DMIDA"
-	help
-	  Select DMIDA if configuring for a DataMyte 4000 Industrial
-	  Digital Assistant. More information at <http://www.dmida.com/>.
-
 config SH_EC3104
 	bool "EC3104"
 	help
@@ -136,25 +117,9 @@
 	  <http://www.m17n.org/linux-sh/dreamcast/>.  There is a
 	  Dreamcast project is at <http://linuxdc.sourceforge.net/>.
 
-config SH_CAT68701
-	bool "CAT68701"
-
 config SH_BIGSUR
 	bool "BigSur"
 
-config SH_SH2000
-	bool "SH2000"
-	select CPU_SUBTYPE_SH7709
-	help
-	  SH-2000 is a single-board computer based around SH7709A chip
-	  intended for embedded applications.
-	  It has an Ethernet interface (CS8900A), direct connected
-	  Compact Flash socket, three serial ports and PC-104 bus.
-	  More information at <http://sh2000.sh-linux.org>.
-
-config SH_ADX
-	bool "ADX"
-
 config SH_MPC1211
 	bool "Interface MPC1211"
 	help
@@ -246,7 +211,7 @@
 
 config CF_ENABLER
 	bool "Compact Flash Enabler support"
-	depends on SH_ADX || SH_SOLUTION_ENGINE || SH_UNKNOWN || SH_CAT68701 || SH_SH03
+	depends on SH_SOLUTION_ENGINE || SH_UNKNOWN || SH_SH03
 	---help---
 	  Compact Flash is a small, removable mass storage device introduced
 	  in 1994 originally as a PCMCIA device.  If you say `Y' here, you
@@ -274,7 +239,7 @@
 	  - "Area5" if CompactFlash is connected to Area 5 (0x14000000)
 	  - "Area6" if it is connected to Area 6 (0x18000000)
 
-	  "Area6" will work for most boards. For ADX, select "Area5".
+	  "Area6" will work for most boards.
 
 config CF_AREA6
 	bool "Area6"
@@ -418,8 +383,8 @@
 
 config HEARTBEAT
 	bool "Heartbeat LED"
-	depends on SH_MPC1211 || SH_SH03 || SH_CAT68701 || \
-		   SH_STB1_HARP || SH_STB1_OVERDRIVE || SH_BIGSUR || \
+	depends on SH_MPC1211 || SH_SH03 || \
+		   SH_BIGSUR || \
 		   SH_7751_SOLUTION_ENGINE || SH_7300_SOLUTION_ENGINE || \
 		   SH_73180_SOLUTION_ENGINE || SH_SOLUTION_ENGINE || \
 		   SH_RTS7751R2D || SH_SH4202_MICRODEV || SH_LANDISK
diff --git a/arch/sh/Makefile b/arch/sh/Makefile
index 8ad0a28..d016884 100644
--- a/arch/sh/Makefile
+++ b/arch/sh/Makefile
@@ -90,18 +90,11 @@
 machdir-$(CONFIG_SH_7751_SOLUTION_ENGINE)	:= se/7751
 machdir-$(CONFIG_SH_7300_SOLUTION_ENGINE)	:= se/7300
 machdir-$(CONFIG_SH_73180_SOLUTION_ENGINE)	:= se/73180
-machdir-$(CONFIG_SH_STB1_HARP)			:= harp
-machdir-$(CONFIG_SH_STB1_OVERDRIVE)		:= overdrive
 machdir-$(CONFIG_SH_HP6XX)			:= hp6xx
-machdir-$(CONFIG_SH_CQREEK)			:= cqreek
-machdir-$(CONFIG_SH_DMIDA)			:= dmida
 machdir-$(CONFIG_SH_EC3104)			:= ec3104
 machdir-$(CONFIG_SH_SATURN)			:= saturn
 machdir-$(CONFIG_SH_DREAMCAST)			:= dreamcast
-machdir-$(CONFIG_SH_CAT68701)			:= cat68701
 machdir-$(CONFIG_SH_BIGSUR)			:= bigsur
-machdir-$(CONFIG_SH_SH2000)			:= sh2000
-machdir-$(CONFIG_SH_ADX)			:= adx
 machdir-$(CONFIG_SH_MPC1211)			:= mpc1211
 machdir-$(CONFIG_SH_SH03)			:= sh03
 machdir-$(CONFIG_SH_SECUREEDGE5410)		:= snapgear
diff --git a/arch/sh/boards/adx/Makefile b/arch/sh/boards/adx/Makefile
deleted file mode 100644
index 5b1c531..0000000
--- a/arch/sh/boards/adx/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Makefile for ADX boards
-#
-
-obj-y	 := setup.o irq.o irq_maskreq.o
-
diff --git a/arch/sh/boards/adx/irq.c b/arch/sh/boards/adx/irq.c
deleted file mode 100644
index c6ca409..0000000
--- a/arch/sh/boards/adx/irq.c
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * linux/arch/sh/boards/adx/irq.c
- *
- * Copyright (C) 2001 A&D Co., Ltd.
- *
- * I/O routine and setup routines for A&D ADX Board
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- */
-
-#include <asm/irq.h>
-
-void init_adx_IRQ(void)
-{
-        int i;
-
-/*      printk("init_adx_IRQ()\n");*/
-        /* setup irq_mask_register */
-        irq_mask_register = (unsigned short *)0xa6000008;
-
-        /* cover all external interrupt area by maskreg_irq_type
-         * (Actually, irq15 doesn't exist)
-         */
-        for (i = 0; i < 16; i++) {
-                make_maskreg_irq(i);
-                disable_irq(i);
-        }
-}
diff --git a/arch/sh/boards/adx/irq_maskreg.c b/arch/sh/boards/adx/irq_maskreg.c
deleted file mode 100644
index 4b2abe5..0000000
--- a/arch/sh/boards/adx/irq_maskreg.c
+++ /dev/null
@@ -1,106 +0,0 @@
-/*
- * linux/arch/sh/kernel/irq_maskreg.c
- *
- * Copyright (C) 2001 A&D Co., Ltd. <http://www.aandd.co.jp>
- *
- * This file may be copied or modified under the terms of the GNU
- * General Public License.  See linux/COPYING for more information.
- *
- * Interrupt handling for Simple external interrupt mask register
- *
- * This is for the machine which have single 16 bit register
- * for masking external IRQ individually.
- * Each bit of the register is for masking each interrupt.  
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/machvec.h>
-
-/* address of external interrupt mask register
- * address must be set prior to use these (maybe in init_XXX_irq())
- * XXX : is it better to use .config than specifying it in code? */
-unsigned short *irq_mask_register = 0;
-
-/* forward declaration */
-static unsigned int startup_maskreg_irq(unsigned int irq);
-static void shutdown_maskreg_irq(unsigned int irq);
-static void enable_maskreg_irq(unsigned int irq);
-static void disable_maskreg_irq(unsigned int irq);
-static void mask_and_ack_maskreg(unsigned int);
-static void end_maskreg_irq(unsigned int irq);
-
-/* hw_interrupt_type */
-static struct hw_interrupt_type maskreg_irq_type = {
-	.typename = " Mask Register",
-	.startup = startup_maskreg_irq,
-	.shutdown = shutdown_maskreg_irq,
-	.enable = enable_maskreg_irq,
-	.disable = disable_maskreg_irq,
-	.ack = mask_and_ack_maskreg,
-	.end = end_maskreg_irq
-};
-
-/* actual implementatin */
-static unsigned int startup_maskreg_irq(unsigned int irq)
-{ 
-	enable_maskreg_irq(irq);
-	return 0; /* never anything pending */
-}
-
-static void shutdown_maskreg_irq(unsigned int irq)
-{
-	disable_maskreg_irq(irq);
-}
-
-static void disable_maskreg_irq(unsigned int irq)
-{
-	if (irq_mask_register) {
-		unsigned long flags;
-		unsigned short val, mask = 0x01 << irq;
-
-		/* Set "irq"th bit */
-		local_irq_save(flags);
-		val = ctrl_inw((unsigned long)irq_mask_register);
-		val |= mask;
-		ctrl_outw(val, (unsigned long)irq_mask_register);
-		local_irq_restore(flags);
-	}
-}
-
-static void enable_maskreg_irq(unsigned int irq)
-{
-	if (irq_mask_register) {
-		unsigned long flags;
-		unsigned short val, mask = ~(0x01 << irq);
-
-		/* Clear "irq"th bit */
-		local_irq_save(flags);
-		val = ctrl_inw((unsigned long)irq_mask_register);
-		val &= mask;
-		ctrl_outw(val, (unsigned long)irq_mask_register);
-		local_irq_restore(flags);
-	}
-}
-
-static void mask_and_ack_maskreg(unsigned int irq)
-{
-	disable_maskreg_irq(irq);
-}
-
-static void end_maskreg_irq(unsigned int irq)
-{
-	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
-		enable_maskreg_irq(irq);
-}
-
-void make_maskreg_irq(unsigned int irq)
-{
-	disable_irq_nosync(irq);
-	irq_desc[irq].chip = &maskreg_irq_type;
-	disable_maskreg_irq(irq);
-}
diff --git a/arch/sh/boards/adx/setup.c b/arch/sh/boards/adx/setup.c
deleted file mode 100644
index 4938d95..0000000
--- a/arch/sh/boards/adx/setup.c
+++ /dev/null
@@ -1,56 +0,0 @@
-/* 
- * linux/arch/sh/board/adx/setup.c
- *
- * Copyright (C) 2001 A&D Co., Ltd.
- *
- * I/O routine and setup routines for A&D ADX Board
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- */
-
-#include <asm/machvec.h>
-#include <linux/module.h>
-
-extern void init_adx_IRQ(void);
-extern void *cf_io_base;
-
-const char *get_system_type(void)
-{
-	return "A&D ADX";
-}
-
-unsigned long adx_isa_port2addr(unsigned long offset)
-{
-	/* CompactFlash (IDE) */
-	if (((offset >= 0x1f0) && (offset <= 0x1f7)) || (offset == 0x3f6)) {
-		return (unsigned long)cf_io_base + offset;
-	}
-
-	/* eth0 */
-	if ((offset >= 0x300) && (offset <= 0x30f)) {
-		return 0xa5000000 + offset;	/* COMM BOARD (AREA1) */
-	}
-
-	return offset + 0xb0000000; /* IOBUS (AREA 4)*/
-}
-
-/*
- * The Machine Vector
- */
-
-struct sh_machine_vector mv_adx __initmv = {
-	.mv_nr_irqs		= 48,
-	.mv_isa_port2addr	= adx_isa_port2addr,
-	.mv_init_irq		= init_adx_IRQ,
-};
-ALIAS_MV(adx)
-
-int __init platform_setup(void)
-{
-	/* Nothing to see here .. */
-	return 0;
-}
-
diff --git a/arch/sh/boards/cat68701/Makefile b/arch/sh/boards/cat68701/Makefile
deleted file mode 100644
index 52c1de0..0000000
--- a/arch/sh/boards/cat68701/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Makefile for the CAT-68701 specific parts of the kernel
-#
-
-obj-y	 := setup.o irq.o
-
diff --git a/arch/sh/boards/cat68701/irq.c b/arch/sh/boards/cat68701/irq.c
deleted file mode 100644
index f9a6d18..0000000
--- a/arch/sh/boards/cat68701/irq.c
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * linux/arch/sh/boards/cat68701/irq.c
- *
- * Copyright (C) 2000  Niibe Yutaka
- *               2001  Yutaro Ebihara
- *
- * Setup routines for A-ONE Corp CAT-68701 SH7708 Board
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- */
-
-#include <asm/irq.h>
-
-int cat68701_irq_demux(int irq)
-{
-        if(irq==13) return 14;
-        if(irq==7)  return 10;
-        return irq;
-}
-
-void init_cat68701_IRQ()
-{
-        make_imask_irq(10);
-        make_imask_irq(14);
-}
diff --git a/arch/sh/boards/cat68701/setup.c b/arch/sh/boards/cat68701/setup.c
deleted file mode 100644
index 90e5175..0000000
--- a/arch/sh/boards/cat68701/setup.c
+++ /dev/null
@@ -1,85 +0,0 @@
-/* 
- * linux/arch/sh/boards/cat68701/setup.c
- *
- * Copyright (C) 2000  Niibe Yutaka
- *               2001  Yutaro Ebihara
- *
- * Setup routines for A-ONE Corp CAT-68701 SH7708 Board
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- */
-
-#include <asm/io.h>
-#include <asm/machvec.h>
-#include <asm/mach/io.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-
-const char *get_system_type(void)
-{
-	return "CAT-68701";
-}
-
-#ifdef CONFIG_HEARTBEAT
-void heartbeat_cat68701()
-{
-        static unsigned int cnt = 0, period = 0 , bit = 0;
-        cnt += 1;
-        if (cnt < period) {
-                return;
-        }
-        cnt = 0;
-
-        /* Go through the points (roughly!):
-         * f(0)=10, f(1)=16, f(2)=20, f(5)=35,f(inf)->110
-         */
-        period = 110 - ( (300<<FSHIFT)/
-                         ((avenrun[0]/5) + (3<<FSHIFT)) );
-
-	if(bit){ bit=0; }else{ bit=1; }
-	outw(bit<<15,0x3fe);
-}
-#endif /* CONFIG_HEARTBEAT */
-
-unsigned long cat68701_isa_port2addr(unsigned long offset)
-{
-	/* CompactFlash (IDE) */
-	if (((offset >= 0x1f0) && (offset <= 0x1f7)) || (offset==0x3f6))
-		return 0xba000000 + offset;
-
-	/* INPUT PORT */
-	if ((offset >= 0x3fc) && (offset <= 0x3fd))
-		return 0xb4007000 + offset;
-
-	/* OUTPUT PORT */
-	if ((offset >= 0x3fe) && (offset <= 0x3ff))
-		return 0xb4007400 + offset;
-
-	return offset + 0xb4000000; /* other I/O (EREA 5)*/
-}
-
-/*
- * The Machine Vector
- */
-
-struct sh_machine_vector mv_cat68701 __initmv = {
-	.mv_nr_irqs		= 32,
-	.mv_isa_port2addr	= cat68701_isa_port2addr,
-	.mv_irq_demux		= cat68701_irq_demux,
-
-	.mv_init_irq		= init_cat68701_IRQ,
-#ifdef CONFIG_HEARTBEAT
-	.mv_heartbeat		= heartbeat_cat68701,
-#endif
-};
-ALIAS_MV(cat68701)
-
-int __init platform_setup(void)
-{
-	/* dummy read erea5 (CS8900A) */
-}
-
diff --git a/arch/sh/boards/cqreek/Makefile b/arch/sh/boards/cqreek/Makefile
deleted file mode 100644
index 1a788a8..0000000
--- a/arch/sh/boards/cqreek/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Makefile for the CqREEK specific parts of the kernel
-#
-
-obj-y	 := setup.o irq.o
-
diff --git a/arch/sh/boards/cqreek/irq.c b/arch/sh/boards/cqreek/irq.c
deleted file mode 100644
index 2955adc..0000000
--- a/arch/sh/boards/cqreek/irq.c
+++ /dev/null
@@ -1,128 +0,0 @@
-/* $Id: irq.c,v 1.1.2.4 2002/11/04 20:33:56 lethal Exp $
- *
- * arch/sh/boards/cqreek/irq.c
- *
- * Copyright (C) 2000  Niibe Yutaka
- *
- * CqREEK IDE/ISA Bridge Support.
- *
- */
-
-#include <linux/irq.h>
-#include <linux/init.h>
-
-#include <asm/cqreek/cqreek.h>
-#include <asm/io.h>
-#include <asm/io_generic.h>
-#include <asm/irq.h>
-#include <asm/machvec.h>
-#include <asm/machvec_init.h>
-#include <asm/rtc.h>
-
-struct cqreek_irq_data {
-	unsigned short mask_port;	/* Port of Interrupt Mask Register */
-	unsigned short stat_port;	/* Port of Interrupt Status Register */
-	unsigned short bit;		/* Value of the bit */
-};
-static struct cqreek_irq_data cqreek_irq_data[NR_IRQS];
-
-static void disable_cqreek_irq(unsigned int irq)
-{
-	unsigned long flags;
-	unsigned short mask;
-	unsigned short mask_port = cqreek_irq_data[irq].mask_port;
-	unsigned short bit = cqreek_irq_data[irq].bit;
-
-	local_irq_save(flags);
-	/* Disable IRQ */
-	mask = inw(mask_port) & ~bit;
-	outw_p(mask, mask_port);
-	local_irq_restore(flags);
-}
-
-static void enable_cqreek_irq(unsigned int irq)
-{
-	unsigned long flags;
-	unsigned short mask;
-	unsigned short mask_port = cqreek_irq_data[irq].mask_port;
-	unsigned short bit = cqreek_irq_data[irq].bit;
-
-	local_irq_save(flags);
-	/* Enable IRQ */
-	mask = inw(mask_port) | bit;
-	outw_p(mask, mask_port);
-	local_irq_restore(flags);
-}
-
-static void mask_and_ack_cqreek(unsigned int irq)
-{
-	unsigned short stat_port = cqreek_irq_data[irq].stat_port;
-	unsigned short bit = cqreek_irq_data[irq].bit;
-
-	disable_cqreek_irq(irq);
-	/* Clear IRQ (it might be edge IRQ) */
-	inw(stat_port);
-	outw_p(bit, stat_port);
-}
-
-static void end_cqreek_irq(unsigned int irq)
-{
-	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
-		enable_cqreek_irq(irq);
-}
-
-static unsigned int startup_cqreek_irq(unsigned int irq)
-{ 
-	enable_cqreek_irq(irq);
-	return 0;
-}
-
-static void shutdown_cqreek_irq(unsigned int irq)
-{
-	disable_cqreek_irq(irq);
-}
-
-static struct hw_interrupt_type cqreek_irq_type = {
-	.typename = "CqREEK-IRQ",
-	.startup = startup_cqreek_irq,
-	.shutdown = shutdown_cqreek_irq,
-	.enable = enable_cqreek_irq,
-	.disable = disable_cqreek_irq,
-	.ack = mask_and_ack_cqreek,
-	.end = end_cqreek_irq
-};
-
-int cqreek_has_ide, cqreek_has_isa;
-
-/* XXX: This is just for test for my NE2000 ISA board
-   What we really need is virtualized IRQ and demultiplexer like HP600 port */
-void __init init_cqreek_IRQ(void)
-{
-	if (cqreek_has_ide) {
-		cqreek_irq_data[14].mask_port = BRIDGE_IDE_INTR_MASK;
-		cqreek_irq_data[14].stat_port = BRIDGE_IDE_INTR_STAT;
-		cqreek_irq_data[14].bit = 1;
-
-		irq_desc[14].chip = &cqreek_irq_type;
-		irq_desc[14].status = IRQ_DISABLED;
-		irq_desc[14].action = 0;
-		irq_desc[14].depth = 1;
-
-		disable_cqreek_irq(14);
-	}
-
-	if (cqreek_has_isa) {
-		cqreek_irq_data[10].mask_port = BRIDGE_ISA_INTR_MASK;
-		cqreek_irq_data[10].stat_port = BRIDGE_ISA_INTR_STAT;
-		cqreek_irq_data[10].bit = (1 << 10);
-
-		/* XXX: Err... we may need demultiplexer for ISA irq... */
-		irq_desc[10].chip = &cqreek_irq_type;
-		irq_desc[10].status = IRQ_DISABLED;
-		irq_desc[10].action = 0;
-		irq_desc[10].depth = 1;
-
-		disable_cqreek_irq(10);
-	}
-}
-
diff --git a/arch/sh/boards/cqreek/setup.c b/arch/sh/boards/cqreek/setup.c
deleted file mode 100644
index eff4ed9..0000000
--- a/arch/sh/boards/cqreek/setup.c
+++ /dev/null
@@ -1,100 +0,0 @@
-/* $Id: setup.c,v 1.5 2003/08/04 01:51:58 lethal Exp $
- *
- * arch/sh/kernel/setup_cqreek.c
- *
- * Copyright (C) 2000  Niibe Yutaka
- *
- * CqREEK IDE/ISA Bridge Support.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/mach/cqreek.h>
-#include <asm/machvec.h>
-#include <asm/io.h>
-#include <asm/io_generic.h>
-#include <asm/irq.h>
-#include <asm/rtc.h>
-
-#define IDE_OFFSET 0xA4000000UL
-#define ISA_OFFSET 0xA4A00000UL
-
-const char *get_system_type(void)
-{
-	return "CqREEK";
-}
-
-static unsigned long cqreek_port2addr(unsigned long port)
-{
-	if (0x0000<=port && port<=0x0040)
-		return IDE_OFFSET + port;
-	if ((0x01f0<=port && port<=0x01f7) || port == 0x03f6)
-		return IDE_OFFSET + port;
-
-	return ISA_OFFSET + port;
-}
-
-/*
- * The Machine Vector
- */
-struct sh_machine_vector mv_cqreek __initmv = {
-#if defined(CONFIG_CPU_SH4)
-	.mv_nr_irqs		= 48,
-#elif defined(CONFIG_CPU_SUBTYPE_SH7708)
-	.mv_nr_irqs		= 32,
-#elif defined(CONFIG_CPU_SUBTYPE_SH7709)
-	.mv_nr_irqs		= 61,
-#endif
-
-	.mv_init_irq		= init_cqreek_IRQ,
-
-	.mv_isa_port2addr	= cqreek_port2addr,
-};
-ALIAS_MV(cqreek)
-
-/*
- * Initialize the board
- */
-void __init platform_setup(void)
-{
-	int i;
-/* udelay is not available at setup time yet... */
-#define DELAY() do {for (i=0; i<10000; i++) ctrl_inw(0xa0000000);} while(0)
-
-	if ((inw (BRIDGE_FEATURE) & 1)) { /* We have IDE interface */
-		outw_p(0, BRIDGE_IDE_INTR_LVL);
-		outw_p(0, BRIDGE_IDE_INTR_MASK);
-
-		outw_p(0, BRIDGE_IDE_CTRL);
-		DELAY();
-
-		outw_p(0x8000, BRIDGE_IDE_CTRL);
-		DELAY();
-
-		outw_p(0xffff, BRIDGE_IDE_INTR_STAT); /* Clear interrupt status */
-		outw_p(0x0f-14, BRIDGE_IDE_INTR_LVL); /* Use 14 IPR */
-		outw_p(1, BRIDGE_IDE_INTR_MASK); /* Enable interrupt */
-		cqreek_has_ide=1;
-	}
-
-	if ((inw (BRIDGE_FEATURE) & 2)) { /* We have ISA interface */
-		outw_p(0, BRIDGE_ISA_INTR_LVL);
-		outw_p(0, BRIDGE_ISA_INTR_MASK);
-
-		outw_p(0, BRIDGE_ISA_CTRL);
-		DELAY();
-		outw_p(0x8000, BRIDGE_ISA_CTRL);
-		DELAY();
-
-		outw_p(0xffff, BRIDGE_ISA_INTR_STAT); /* Clear interrupt status */
-		outw_p(0x0f-10, BRIDGE_ISA_INTR_LVL); /* Use 10 IPR */
-		outw_p(0xfff8, BRIDGE_ISA_INTR_MASK); /* Enable interrupt */
-		cqreek_has_isa=1;
-	}
-
-	printk(KERN_INFO "CqREEK Setup (IDE=%d, ISA=%d)...done\n", cqreek_has_ide, cqreek_has_isa);
-}
-
diff --git a/arch/sh/boards/dmida/Makefile b/arch/sh/boards/dmida/Makefile
deleted file mode 100644
index 75999aa..0000000
--- a/arch/sh/boards/dmida/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-#
-# Makefile for the DataMyte Industrial Digital Assistant(tm) specific parts
-# of the kernel
-#
-
-obj-y	 := mach.o
-
diff --git a/arch/sh/boards/dmida/mach.c b/arch/sh/boards/dmida/mach.c
deleted file mode 100644
index d03a25f9..0000000
--- a/arch/sh/boards/dmida/mach.c
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * linux/arch/sh/boards/dmida/mach.c
- *
- * by Greg Banks <gbanks@pocketpenguins.com>
- * (c) 2000 PocketPenguins Inc
- *
- * Derived from mach_hp600.c, which bore the message:
- * Copyright (C) 2000 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * Machine vector for the DataMyte Industrial Digital Assistant(tm).
- * See http://www.dmida.com
- *
- */
-
-#include <linux/init.h>
-
-#include <asm/machvec.h>
-#include <asm/rtc.h>
-#include <asm/machvec_init.h>
-
-#include <asm/io.h>
-#include <asm/hd64465/hd64465.h>
-#include <asm/irq.h>
-
-/*
- * The Machine Vector
- */
-
-struct sh_machine_vector mv_dmida __initmv = {
-	.mv_nr_irqs		= HD64465_IRQ_BASE+HD64465_IRQ_NUM,
-
-	.mv_inb			= hd64465_inb,
-	.mv_inw			= hd64465_inw,
-	.mv_inl			= hd64465_inl,
-	.mv_outb		= hd64465_outb,
-	.mv_outw		= hd64465_outw,
-	.mv_outl		= hd64465_outl,
-
-	.mv_inb_p		= hd64465_inb_p,
-	.mv_inw_p		= hd64465_inw,
-	.mv_inl_p		= hd64465_inl,
-	.mv_outb_p		= hd64465_outb_p,
-	.mv_outw_p		= hd64465_outw,
-	.mv_outl_p		= hd64465_outl,
-
-	.mv_insb		= hd64465_insb,
-	.mv_insw		= hd64465_insw,
-	.mv_insl		= hd64465_insl,
-	.mv_outsb		= hd64465_outsb,
-	.mv_outsw		= hd64465_outsw,
-	.mv_outsl		= hd64465_outsl,
-
-	.mv_irq_demux		= hd64465_irq_demux,
-};
-ALIAS_MV(dmida)
-
diff --git a/arch/sh/boards/harp/Makefile b/arch/sh/boards/harp/Makefile
deleted file mode 100644
index eb753d3..0000000
--- a/arch/sh/boards/harp/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Makefile for STMicroelectronics board specific parts of the kernel
-#
-
-obj-y := irq.o setup.o mach.o led.o
-
-obj-$(CONFIG_PCI) += pcidma.o
-
diff --git a/arch/sh/boards/harp/irq.c b/arch/sh/boards/harp/irq.c
deleted file mode 100644
index 96bb41c..0000000
--- a/arch/sh/boards/harp/irq.c
+++ /dev/null
@@ -1,147 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * Looks after interrupts on the HARP board.
- *
- * Bases on the IPR irq system
- */
-
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/harp/harp.h>
-
-
-#define NUM_EXTERNAL_IRQS 16
-
-// Early versions of the STB1 Overdrive required this nasty frig
-//#define INVERT_INTMASK_WRITES
-
-static void enable_harp_irq(unsigned int irq);
-static void disable_harp_irq(unsigned int irq);
-
-/* shutdown is same as "disable" */
-#define shutdown_harp_irq disable_harp_irq
-
-static void mask_and_ack_harp(unsigned int);
-static void end_harp_irq(unsigned int irq);
-
-static unsigned int startup_harp_irq(unsigned int irq)
-{
-	enable_harp_irq(irq);
-	return 0;		/* never anything pending */
-}
-
-static struct hw_interrupt_type harp_irq_type = {
-	.typename = "Harp-IRQ",
-	.startup = startup_harp_irq,
-	.shutdown = shutdown_harp_irq,
-	.enable = enable_harp_irq,
-	.disable = disable_harp_irq,
-	.ack = mask_and_ack_harp,
-	.end = end_harp_irq
-};
-
-static void disable_harp_irq(unsigned int irq)
-{
-	unsigned val, flags;
-	unsigned maskReg;
-	unsigned mask;
-	int pri;
-
-	if (irq < 0 || irq >= NUM_EXTERNAL_IRQS)
-		return;
-
-	pri = 15 - irq;
-
-	if (pri < 8) {
-		maskReg = EPLD_INTMASK0;
-	} else {
-		maskReg = EPLD_INTMASK1;
-		pri -= 8;
-	}
-
-	local_irq_save(flags);
-	mask = ctrl_inl(maskReg);
-	mask &= (~(1 << pri));
-#if defined(INVERT_INTMASK_WRITES)
-	mask ^= 0xff;
-#endif
-	ctrl_outl(mask, maskReg);
-	local_irq_restore(flags);
-}
-
-static void enable_harp_irq(unsigned int irq)
-{
-	unsigned flags;
-	unsigned maskReg;
-	unsigned mask;
-	int pri;
-
-	if (irq < 0 || irq >= NUM_EXTERNAL_IRQS)
-		return;
-
-	pri = 15 - irq;
-
-	if (pri < 8) {
-		maskReg = EPLD_INTMASK0;
-	} else {
-		maskReg = EPLD_INTMASK1;
-		pri -= 8;
-	}
-
-	local_irq_save(flags);
-	mask = ctrl_inl(maskReg);
-
-
-	mask |= (1 << pri);
-
-#if defined(INVERT_INTMASK_WRITES)
-	mask ^= 0xff;
-#endif
-	ctrl_outl(mask, maskReg);
-
-	local_irq_restore(flags);
-}
-
-/* This functions sets the desired irq handler to be an overdrive type */
-static void __init make_harp_irq(unsigned int irq)
-{
-	disable_irq_nosync(irq);
-	irq_desc[irq].chip = &harp_irq_type;
-	disable_harp_irq(irq);
-}
-
-static void mask_and_ack_harp(unsigned int irq)
-{
-	disable_harp_irq(irq);
-}
-
-static void end_harp_irq(unsigned int irq)
-{
-	enable_harp_irq(irq);
-}
-
-void __init init_harp_irq(void)
-{
-	int i;
-
-#if !defined(INVERT_INTMASK_WRITES)
-	// On the harp these are set to enable an interrupt
-	ctrl_outl(0x00, EPLD_INTMASK0);
-	ctrl_outl(0x00, EPLD_INTMASK1);
-#else
-	// On the Overdrive the data is inverted before being stored in the reg
-	ctrl_outl(0xff, EPLD_INTMASK0);
-	ctrl_outl(0xff, EPLD_INTMASK1);
-#endif
-
-	for (i = 0; i < NUM_EXTERNAL_IRQS; i++) {
-		make_harp_irq(i);
-	}
-}
diff --git a/arch/sh/boards/harp/led.c b/arch/sh/boards/harp/led.c
deleted file mode 100644
index aeb7b39..0000000
--- a/arch/sh/boards/harp/led.c
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * linux/arch/sh/stboards/led.c
- *
- * Copyright (C) 2000 Stuart Menefy <stuart.menefy@st.com>
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * This file contains ST40STB1 HARP and compatible code.
- */
-
-#include <asm/io.h>
-#include <asm/harp/harp.h>
-
-/* Harp: Flash LD10 (front pannel) connected to EPLD (IC8) */
-/* Overdrive: Flash LD1 (front panel) connected to EPLD (IC4) */
-/* Works for HARP and overdrive */
-static void mach_led(int position, int value)
-{
-	if (value) {
-		ctrl_outl(EPLD_LED_ON, EPLD_LED);
-	} else {
-		ctrl_outl(EPLD_LED_OFF, EPLD_LED);
-	}
-}
-
-#ifdef CONFIG_HEARTBEAT
-
-#include <linux/sched.h>
-
-/* acts like an actual heart beat -- ie thump-thump-pause... */
-void heartbeat_harp(void)
-{
-	static unsigned cnt = 0, period = 0, dist = 0;
-
-	if (cnt == 0 || cnt == dist)
-		mach_led( -1, 1);
-	else if (cnt == 7 || cnt == dist+7)
-		mach_led( -1, 0);
-
-	if (++cnt > period) {
-		cnt = 0;
-		/* The hyperbolic function below modifies the heartbeat period
-		 * length in dependency of the current (5min) load. It goes
-		 * through the points f(0)=126, f(1)=86, f(5)=51,
-		 * f(inf)->30. */
-		period = ((672<<FSHIFT)/(5*avenrun[0]+(7<<FSHIFT))) + 30;
-		dist = period / 4;
-	}
-}
-#endif
diff --git a/arch/sh/boards/harp/mach.c b/arch/sh/boards/harp/mach.c
deleted file mode 100644
index a946dd1..0000000
--- a/arch/sh/boards/harp/mach.c
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
- * linux/arch/sh/boards/harp/mach.c
- *
- * Copyright (C) 2000 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * Machine vector for the STMicroelectronics STB1 HARP and compatible boards
- */
-
-#include <linux/init.h>
-
-#include <asm/machvec.h>
-#include <asm/rtc.h>
-#include <asm/machvec_init.h>
-#include <asm/hd64465/io.h>
-#include <asm/hd64465/hd64465.h>
-
-void setup_harp(void);
-void init_harp_irq(void);
-void heartbeat_harp(void);
-
-/*
- * The Machine Vector
- */
-
-struct sh_machine_vector mv_harp __initmv = {
-	.mv_nr_irqs		= 89 + HD64465_IRQ_NUM,
-
-	.mv_inb			= hd64465_inb,
-	.mv_inw			= hd64465_inw,
-	.mv_inl			= hd64465_inl,
-	.mv_outb		= hd64465_outb,
-	.mv_outw		= hd64465_outw,
-	.mv_outl		= hd64465_outl,
-
-	.mv_inb_p		= hd64465_inb_p,
-	.mv_inw_p		= hd64465_inw,
-	.mv_inl_p		= hd64465_inl,
-	.mv_outb_p		= hd64465_outb_p,
-	.mv_outw_p		= hd64465_outw,
-	.mv_outl_p		= hd64465_outl,
-
-	.mv_insb		= hd64465_insb,
-	.mv_insw		= hd64465_insw,
-	.mv_insl		= hd64465_insl,
-	.mv_outsb		= hd64465_outsb,
-	.mv_outsw		= hd64465_outsw,
-	.mv_outsl		= hd64465_outsl,
-
-        .mv_isa_port2addr       = hd64465_isa_port2addr,
-
-#ifdef CONFIG_PCI
-	.mv_init_irq		= init_harp_irq,
-#endif
-#ifdef CONFIG_HEARTBEAT
-	.mv_heartbeat		= heartbeat_harp,
-#endif
-};
-
-ALIAS_MV(harp)
diff --git a/arch/sh/boards/harp/pcidma.c b/arch/sh/boards/harp/pcidma.c
deleted file mode 100644
index 4753113..0000000
--- a/arch/sh/boards/harp/pcidma.c
+++ /dev/null
@@ -1,42 +0,0 @@
-/* 
- * Copyright (C) 2001 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * Dynamic DMA mapping support.
- */
-
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/string.h>
-#include <linux/pci.h>
-#include <asm/io.h>
-#include <asm/addrspace.h>
-
-
-void *pci_alloc_consistent(struct pci_dev *hwdev, size_t size,
-			   dma_addr_t * dma_handle)
-{
-	void *ret;
-	int gfp = GFP_ATOMIC;
-
-	ret = (void *) __get_free_pages(gfp, get_order(size));
-
-	if (ret != NULL) {
-	        /* Is it neccessary to do the memset? */
-		memset(ret, 0, size);
-		*dma_handle = virt_to_bus(ret);
-	}
-	/* We must flush the cache before we pass it on to the device */
-	flush_cache_all();
-	return  P2SEGADDR(ret);
-}
-
-void pci_free_consistent(struct pci_dev *hwdev, size_t size,
-			 void *vaddr, dma_addr_t dma_handle)
-{
-        unsigned long p1addr=P1SEGADDR((unsigned long)vaddr);
-
-	free_pages(p1addr, get_order(size));
-}
diff --git a/arch/sh/boards/harp/setup.c b/arch/sh/boards/harp/setup.c
deleted file mode 100644
index 886e450..0000000
--- a/arch/sh/boards/harp/setup.c
+++ /dev/null
@@ -1,90 +0,0 @@
-/*
- * arch/sh/stboard/setup.c
- *
- * Copyright (C) 2001 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * STMicroelectronics ST40STB1 HARP and compatible support.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <asm/io.h>
-#include <asm/harp/harp.h>
-
-const char *get_system_type(void)
-{
-	return "STB1 Harp";
-}
-
-/*
- * Initialize the board
- */
-int __init platform_setup(void)
-{
-#ifdef CONFIG_SH_STB1_HARP
-	unsigned long ic8_version, ic36_version;
-
-	ic8_version = ctrl_inl(EPLD_REVID2);
-	ic36_version = ctrl_inl(EPLD_REVID1);
-
-        printk("STMicroelectronics STB1 HARP initialisaton\n");
-        printk("EPLD versions: IC8: %d.%02d, IC36: %d.%02d\n",
-               (ic8_version >> 4) & 0xf, ic8_version & 0xf,
-               (ic36_version >> 4) & 0xf, ic36_version & 0xf);
-#elif defined(CONFIG_SH_STB1_OVERDRIVE)
-	unsigned long version;
-
-	version = ctrl_inl(EPLD_REVID);
-
-        printk("STMicroelectronics STB1 Overdrive initialisaton\n");
-        printk("EPLD version: %d.%02d\n",
-	       (version >> 4) & 0xf, version & 0xf);
-#else
-#error Undefined machine
-#endif
- 
-        /* Currently all STB1 chips have problems with the sleep instruction,
-         * so disable it here.
-         */
-	disable_hlt();
-
-	return 0;
-}
-
-/*
- * pcibios_map_platform_irq
- *
- * This is board specific and returns the IRQ for a given PCI device.
- * It is used by the PCI code (arch/sh/kernel/st40_pci*)
- *
- */
-
-#define HARP_PCI_IRQ    1
-#define HARP_BRIDGE_IRQ 2
-#define OVERDRIVE_SLOT0_IRQ 0
-
-
-int __init pcibios_map_platform_irq(struct pci_dev *dev, u8 slot, u8 pin)
-{
-	switch (slot) {
-#ifdef CONFIG_SH_STB1_HARP
-	case 2:		/*This is the PCI slot on the */
-		return HARP_PCI_IRQ;
-	case 1:		/* this is the bridge */
-		return HARP_BRIDGE_IRQ;
-#elif defined(CONFIG_SH_STB1_OVERDRIVE)
-	case 1:
-	case 2:
-	case 3:
-		return slot - 1;
-#else
-#error Unknown board
-#endif
-	default:
-		return -1;
-	}
-}
-
diff --git a/arch/sh/boards/overdrive/Makefile b/arch/sh/boards/overdrive/Makefile
deleted file mode 100644
index 245f03b..0000000
--- a/arch/sh/boards/overdrive/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Makefile for the STMicroelectronics Overdrive specific parts of the kernel
-#
-
-obj-y	 := mach.o setup.o io.o irq.o led.o
-
-obj-$(CONFIG_PCI) += fpga.o galileo.o pcidma.o
-
diff --git a/arch/sh/boards/overdrive/fpga.c b/arch/sh/boards/overdrive/fpga.c
deleted file mode 100644
index 956c239..0000000
--- a/arch/sh/boards/overdrive/fpga.c
+++ /dev/null
@@ -1,133 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * This file handles programming up the Altera Flex10K that interfaces to
- * the Galileo, and does the PS/2 keyboard and mouse
- *
- */
-
-
-#include <linux/kernel.h>
-#include <linux/smp.h>
-#include <linux/smp_lock.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-
-
-#include <asm/overdriver/gt64111.h>
-#include <asm/overdrive/overdrive.h>
-#include <asm/overdrive/fpga.h>
-
-#define FPGA_NotConfigHigh()  (*FPGA_ControlReg) = (*FPGA_ControlReg) | ENABLE_FPGA_BIT
-#define FPGA_NotConfigLow()   (*FPGA_ControlReg) = (*FPGA_ControlReg) & RESET_FPGA_MASK
-
-/* I need to find out what (if any) the real delay factor here is */
-/* The delay is definately not critical */
-#define long_delay() {int i;for(i=0;i<10000;i++);}
-#define short_delay() {int i;for(i=0;i<100;i++);}
-
-static void __init program_overdrive_fpga(const unsigned char *fpgacode,
-					  int size)
-{
-	int timeout = 0;
-	int i, j;
-	unsigned char b;
-	static volatile unsigned char *FPGA_ControlReg =
-	    (volatile unsigned char *) (OVERDRIVE_CTRL);
-	static volatile unsigned char *FPGA_ProgramReg =
-	    (volatile unsigned char *) (FPGA_DCLK_ADDRESS);
-
-	printk("FPGA:  Commencing FPGA Programming\n");
-
-	/* The PCI reset but MUST be low when programming the FPGA !!! */
-	b = (*FPGA_ControlReg) & RESET_PCI_MASK;
-
-	(*FPGA_ControlReg) = b;
-
-	/* Prepare FPGA to program */
-
-	FPGA_NotConfigHigh();
-	long_delay();
-
-	FPGA_NotConfigLow();
-	short_delay();
-
-	while ((*FPGA_ProgramReg & FPGA_NOT_STATUS) != 0) {
-		printk("FPGA:  Waiting for NotStatus to go Low ... \n");
-	}
-
-	FPGA_NotConfigHigh();
-
-	/* Wait for FPGA "ready to be programmed" signal */
-	printk("FPGA:  Waiting for NotStatus to go high (FPGA ready)... \n");
-
-	for (timeout = 0;
-	     (((*FPGA_ProgramReg & FPGA_NOT_STATUS) == 0)
-	      && (timeout < FPGA_TIMEOUT)); timeout++);
-
-	/* Check if timeout condition occured - i.e. an error */
-
-	if (timeout == FPGA_TIMEOUT) {
-		printk
-		    ("FPGA:  Failed to program - Timeout waiting for notSTATUS to go high\n");
-		return;
-	}
-
-	printk("FPGA:  Copying data to FPGA ... %d bytes\n", size);
-
-	/* Copy array to FPGA - bit at a time */
-
-	for (i = 0; i < size; i++) {
-		volatile unsigned w = 0;
-
-		for (j = 0; j < 8; j++) {
-			*FPGA_ProgramReg = (fpgacode[i] >> j) & 0x01;
-			short_delay();
-		}
-		if ((i & 0x3ff) == 0) {
-			printk(".");
-		}
-	}
-
-	/* Waiting for CONFDONE to go high - means the program is complete  */
-
-	for (timeout = 0;
-	     (((*FPGA_ProgramReg & FPGA_CONFDONE) == 0)
-	      && (timeout < FPGA_TIMEOUT)); timeout++) {
-
-		*FPGA_ProgramReg = 0x0;
-		long_delay();
-	}
-
-	if (timeout == FPGA_TIMEOUT) {
-		printk
-		    ("FPGA:  Failed to program - Timeout waiting for CONFDONE to go high\n");
-		return;
-	} else {		/* Clock another 10 times - gets the device into a working state      */
-		for (i = 0; i < 10; i++) {
-			*FPGA_ProgramReg = 0x0;
-			short_delay();
-		}
-	}
-
-	printk("FPGA:  Programming complete\n");
-}
-
-
-static const unsigned char __init fpgacode[] = {
-#include "./overdrive.ttf"	/* Code from maxplus2 compiler */
-	, 0, 0
-};
-
-
-int __init init_overdrive_fpga(void)
-{
-	program_overdrive_fpga(fpgacode, sizeof(fpgacode));
-
-	return 0;
-}
diff --git a/arch/sh/boards/overdrive/galileo.c b/arch/sh/boards/overdrive/galileo.c
deleted file mode 100644
index 29e4897..0000000
--- a/arch/sh/boards/overdrive/galileo.c
+++ /dev/null
@@ -1,587 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * This file contains the PCI routines required for the Galileo GT6411 
- * PCI bridge as used on the Orion and Overdrive boards.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/smp.h>
-#include <linux/smp_lock.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/ioport.h>
-
-#include <asm/overdrive/overdrive.h>
-#include <asm/overdrive/gt64111.h>
-
-
-/* After boot, we shift the Galileo registers so that they appear 
- * in BANK6, along with IO space. This means we can have one contingous
- * lump of PCI address space without these registers appearing in the 
- * middle of them 
- */
-
-#define GT64111_BASE_ADDRESS  0xbb000000
-#define GT64111_IO_BASE_ADDRESS  0x1000
-/* The GT64111 registers appear at this address to the SH4 after reset */
-#define RESET_GT64111_BASE_ADDRESS           0xb4000000
-
-/* Macros used to access the Galileo registers */
-#define RESET_GT64111_REG(x) (RESET_GT64111_BASE_ADDRESS+x)
-#define GT64111_REG(x) (GT64111_BASE_ADDRESS+x)
-
-#define RESET_GT_WRITE(x,v) writel((v),RESET_GT64111_REG(x))
-
-#define RESET_GT_READ(x) readl(RESET_GT64111_REG(x))
-
-#define GT_WRITE(x,v) writel((v),GT64111_REG(x))
-#define GT_WRITE_BYTE(x,v) writeb((v),GT64111_REG(x))
-#define GT_WRITE_SHORT(x,v) writew((v),GT64111_REG(x))
-
-#define GT_READ(x)    readl(GT64111_REG(x))
-#define GT_READ_BYTE(x)  readb(GT64111_REG(x))
-#define GT_READ_SHORT(x) readw(GT64111_REG(x))
-
-
-/* Where the various SH banks start at */
-#define SH_BANK4_ADR 0xb0000000
-#define SH_BANK5_ADR 0xb4000000
-#define SH_BANK6_ADR 0xb8000000
-
-/* Masks out everything but lines 28,27,26 */
-#define BANK_SELECT_MASK 0x1c000000
-
-#define SH4_TO_BANK(x) ( (x) & BANK_SELECT_MASK)
-
-/* 
- * Masks used for address conversaion. Bank 6 is used for IO and 
- * has all the address bits zeroed by the FPGA. Special case this
- */
-#define MEMORY_BANK_MASK 0x1fffffff
-#define IO_BANK_MASK  0x03ffffff
-
-/* Mark bank 6 as the bank used for IO. You can change this in the FPGA code
- * if you want 
- */
-#define IO_BANK_ADR PCI_GTIO_BASE
-
-/* Will select the correct mask to apply depending on the SH$ address */
-#define SELECT_BANK_MASK(x) \
-   ( (SH4_TO_BANK(x)==SH4_TO_BANK(IO_BANK_ADR)) ? IO_BANK_MASK : MEMORY_BANK_MASK)
-
-/* Converts between PCI space and P2 region */
-#define SH4_TO_PCI(x) ((x)&SELECT_BANK_MASK(x))
-
-/* Various macros for figuring out what to stick in the Galileo registers. 
- * You *really* don't want to figure this stuff out by hand, you always get
- * it wrong
- */
-#define GT_MEM_LO_ADR(x) ((((unsigned)((x)&SELECT_BANK_MASK(x)))>>21)&0x7ff)
-#define GT_MEM_HI_ADR(x) ((((unsigned)((x)&SELECT_BANK_MASK(x)))>>21)&0x7f)
-#define GT_MEM_SUB_ADR(x) ((((unsigned)((x)&SELECT_BANK_MASK(x)))>>20)&0xff)
-
-#define PROGRAM_HI_LO(block,a,s) \
-    GT_WRITE(block##_LO_DEC_ADR,GT_MEM_LO_ADR(a));\
-    GT_WRITE(block##_HI_DEC_ADR,GT_MEM_HI_ADR(a+s-1))
-
-#define PROGRAM_SUB_HI_LO(block,a,s) \
-    GT_WRITE(block##_LO_DEC_ADR,GT_MEM_SUB_ADR(a));\
-    GT_WRITE(block##_HI_DEC_ADR,GT_MEM_SUB_ADR(a+s-1))
-
-/* We need to set the size, and the offset register */
-
-#define GT_BAR_MASK(x) ((x)&~0xfff)
-
-/* Macro to set up the BAR in the Galileo. Essentially used for the DRAM */
-#define PROGRAM_GT_BAR(block,a,s) \
-  GT_WRITE(PCI_##block##_BANK_SIZE,GT_BAR_MASK((s-1)));\
-  write_config_to_galileo(PCI_CONFIG_##block##_BASE_ADR,\
-			     GT_BAR_MASK(a))
-
-#define DISABLE_GT_BAR(block) \
-  GT_WRITE(PCI_##block##_BANK_SIZE,0),\
-  GT_CONFIG_WRITE(PCI_CONFIG_##block##_BASE_ADR,\
-    0x80000000)
-
-/* Macros to disable things we are not going to use */
-#define DISABLE_DECODE(x) GT_WRITE(x##_LO_DEC_ADR,0x7ff);\
-                          GT_WRITE(x##_HI_DEC_ADR,0x00)
-
-#define DISABLE_SUB_DECODE(x) GT_WRITE(x##_LO_DEC_ADR,0xff);\
-                              GT_WRITE(x##_HI_DEC_ADR,0x00)
-
-static void __init reset_pci(void)
-{
-	/* Set RESET_PCI bit high */
-	writeb(readb(OVERDRIVE_CTRL) | ENABLE_PCI_BIT, OVERDRIVE_CTRL);
-	udelay(250);
-
-	/* Set RESET_PCI bit low */
-	writeb(readb(OVERDRIVE_CTRL) & RESET_PCI_MASK, OVERDRIVE_CTRL);
-	udelay(250);
-
-	writeb(readb(OVERDRIVE_CTRL) | ENABLE_PCI_BIT, OVERDRIVE_CTRL);
-	udelay(250);
-}
-
-static int write_config_to_galileo(int where, u32 val);
-#define GT_CONFIG_WRITE(where,val) write_config_to_galileo(where,val)
-
-#define ENABLE_PCI_DRAM
-
-
-#ifdef TEST_DRAM
-/* Test function to check out if the PCI DRAM is working OK */
-static int  /* __init */ test_dram(unsigned *base, unsigned size)
-{
-	unsigned *p = base;
-	unsigned *end = (unsigned *) (((unsigned) base) + size);
-	unsigned w;
-
-	for (p = base; p < end; p++) {
-		*p = 0xffffffff;
-		if (*p != 0xffffffff) {
-			printk("AAARGH -write failed!!! at %p is %x\n", p,
-			       *p);
-			return 0;
-		}
-		*p = 0x0;
-		if (*p != 0x0) {
-			printk("AAARGH -write failed!!!\n");
-			return 0;
-		}
-	}
-
-	for (p = base; p < end; p++) {
-		*p = (unsigned) p;
-		if (*p != (unsigned) p) {
-			printk("Failed at 0x%p, actually is 0x%x\n", p,
-			       *p);
-			return 0;
-		}
-	}
-
-	for (p = base; p < end; p++) {
-		w = ((unsigned) p & 0xffff0000);
-		*p = w | (w >> 16);
-	}
-
-	for (p = base; p < end; p++) {
-		w = ((unsigned) p & 0xffff0000);
-		w |= (w >> 16);
-		if (*p != w) {
-			printk
-			    ("Failed at 0x%p, should be 0x%x actually is 0x%x\n",
-			     p, w, *p);
-			return 0;
-		}
-	}
-
-	return 1;
-}
-#endif
-
-
-/* Function to set up and initialise the galileo. This sets up the BARS,
- * maps the DRAM into the address space etc,etc
- */
-int __init galileo_init(void)
-{
-	reset_pci();
-
-	/* Now shift the galileo regs into this block */
-	RESET_GT_WRITE(INTERNAL_SPACE_DEC,
-		       GT_MEM_LO_ADR(GT64111_BASE_ADDRESS));
-
-	/* Should have a sanity check here, that you can read back  at the new
-	 * address what you just wrote 
-	 */
-
-	/* Disable decode for all regions */
-	DISABLE_DECODE(RAS10);
-	DISABLE_DECODE(RAS32);
-	DISABLE_DECODE(CS20);
-	DISABLE_DECODE(CS3);
-	DISABLE_DECODE(PCI_IO);
-	DISABLE_DECODE(PCI_MEM0);
-	DISABLE_DECODE(PCI_MEM1);
-
-	/* Disable all BARS */
-	GT_WRITE(BAR_ENABLE_ADR, 0x1ff);
-	DISABLE_GT_BAR(RAS10);
-	DISABLE_GT_BAR(RAS32);
-	DISABLE_GT_BAR(CS20);
-	DISABLE_GT_BAR(CS3);
-
-	/* Tell the BAR where the IO registers now are */
-	GT_CONFIG_WRITE(PCI_CONFIG_INT_REG_IO_ADR,GT_BAR_MASK(
-					    (GT64111_IO_BASE_ADDRESS &
-					     IO_BANK_MASK)));
-	/* set up a 112 Mb decode */
-	PROGRAM_HI_LO(PCI_MEM0, SH_BANK4_ADR, 112 * 1024 * 1024);
-
-	/* Set up a 32 MB io space decode */
-	PROGRAM_HI_LO(PCI_IO, IO_BANK_ADR, 32 * 1024 * 1024);
-
-#ifdef ENABLE_PCI_DRAM
-	/* Program up the DRAM configuration - there is DRAM only in bank 0 */
-	/* Now set up the DRAM decode */
-	PROGRAM_HI_LO(RAS10, PCI_DRAM_BASE, PCI_DRAM_SIZE);
-	/* And the sub decode */
-	PROGRAM_SUB_HI_LO(RAS0, PCI_DRAM_BASE, PCI_DRAM_SIZE);
-
-	DISABLE_SUB_DECODE(RAS1);
-
-	/* Set refresh rate */
-	GT_WRITE(DRAM_BANK0_PARMS, 0x3f);
-	GT_WRITE(DRAM_CFG, 0x100);
-
-	/* we have to lob off the top bits rememeber!! */
-	PROGRAM_GT_BAR(RAS10, SH4_TO_PCI(PCI_DRAM_BASE), PCI_DRAM_SIZE);
-
-#endif
-
-	/* We are only interested in decoding RAS10 and the Galileo's internal 
-	 * registers (as IO) on the PCI bus
-	 */
-#ifdef ENABLE_PCI_DRAM
-	GT_WRITE(BAR_ENABLE_ADR, (~((1 << 8) | (1 << 3))) & 0x1ff);
-#else
-	GT_WRITE(BAR_ENABLE_ADR, (~(1 << 3)) & 0x1ff);
-#endif
-
-	/* Change the class code to host bridge, it actually powers up 
-	 * as a memory controller
-         */
-	GT_CONFIG_WRITE(8, 0x06000011);
-
-	/* Allow the galileo to master the PCI bus */
-	GT_CONFIG_WRITE(PCI_COMMAND,
-			PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
-			PCI_COMMAND_IO);
-
-
-#if 0
-        printk("Testing PCI DRAM - ");
-	if(test_dram(PCI_DRAM_BASE,PCI_DRAM_SIZE)) {
-		printk("Passed\n");
-	}else {
-		printk("FAILED\n");
-	}
-#endif
-	return 0;
-
-}
-
-
-#define SET_CONFIG_BITS(bus,devfn,where)\
-  ((1<<31) | ((bus) << 16) | ((devfn) << 8) | ((where) & ~3))
-
-#define CONFIG_CMD(dev, where) SET_CONFIG_BITS((dev)->bus->number,(dev)->devfn,where)
-
-/* This write to the galileo config registers, unlike the functions below, can
- * be used before the PCI subsystem has started up
- */
-static int __init write_config_to_galileo(int where, u32 val)
-{
-	GT_WRITE(PCI_CFG_ADR, SET_CONFIG_BITS(0, 0, where));
-
-	GT_WRITE(PCI_CFG_DATA, val);
-	return 0;
-}
-
-/* We exclude the galileo and slot 31, the galileo because I don't know how to stop
- * the setup code shagging up the setup I have done on it, and 31 because the whole
- * thing locks up if you try to access that slot (which doesn't exist of course anyway
- */
-
-#define EXCLUDED_DEV(dev) ((dev->bus->number==0) && ((PCI_SLOT(dev->devfn)==0) || (PCI_SLOT(dev->devfn) == 31)))
-
-static int galileo_read_config_byte(struct pci_dev *dev, int where,
-				    u8 * val)
-{
-
-        
-	/* I suspect this doesn't work because this drives a special cycle ? */
-	if (EXCLUDED_DEV(dev)) {
-		*val = 0xff;
-		return PCIBIOS_SUCCESSFUL;
-	}
-	/* Start the config cycle */
-	GT_WRITE(PCI_CFG_ADR, CONFIG_CMD(dev, where));
-	/* Read back the result */
-	*val = GT_READ_BYTE(PCI_CFG_DATA + (where & 3));
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-
-static int galileo_read_config_word(struct pci_dev *dev, int where,
-				    u16 * val)
-{
-
-        if (EXCLUDED_DEV(dev)) {
-		*val = 0xffff;
-		return PCIBIOS_SUCCESSFUL;
-	}
-
-	GT_WRITE(PCI_CFG_ADR, CONFIG_CMD(dev, where));
-	*val = GT_READ_SHORT(PCI_CFG_DATA + (where & 2));
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-
-static int galileo_read_config_dword(struct pci_dev *dev, int where,
-				     u32 * val)
-{
-	if (EXCLUDED_DEV(dev)) {
-		*val = 0xffffffff;
-		return PCIBIOS_SUCCESSFUL;
-	}
-
-	GT_WRITE(PCI_CFG_ADR, CONFIG_CMD(dev, where));
-	*val = GT_READ(PCI_CFG_DATA);
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int galileo_write_config_byte(struct pci_dev *dev, int where,
-				     u8 val)
-{
-	GT_WRITE(PCI_CFG_ADR, CONFIG_CMD(dev, where));
-
-	GT_WRITE_BYTE(PCI_CFG_DATA + (where & 3), val);
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-
-static int galileo_write_config_word(struct pci_dev *dev, int where,
-				     u16 val)
-{
-	GT_WRITE(PCI_CFG_ADR, CONFIG_CMD(dev, where));
-
-	GT_WRITE_SHORT(PCI_CFG_DATA + (where & 2), val);
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int galileo_write_config_dword(struct pci_dev *dev, int where,
-				      u32 val)
-{
-	GT_WRITE(PCI_CFG_ADR, CONFIG_CMD(dev, where));
-
-	GT_WRITE(PCI_CFG_DATA, val);
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static struct pci_ops pci_config_ops = {
-	galileo_read_config_byte,
-	galileo_read_config_word,
-	galileo_read_config_dword,
-	galileo_write_config_byte,
-	galileo_write_config_word,
-	galileo_write_config_dword
-};
-
-
-/* Everything hangs off this */
-static struct pci_bus *pci_root_bus;
-
-
-static u8 __init no_swizzle(struct pci_dev *dev, u8 * pin)
-{
-	return PCI_SLOT(dev->devfn);
-}
-
-static int __init map_od_irq(struct pci_dev *dev, u8 slot, u8 pin)
-{
-	/* Slot 1: Galileo 
-	 * Slot 2: PCI Slot 1
-	 * Slot 3: PCI Slot 2
-	 * Slot 4: ESS
-	 */
-	switch (slot) {
-	case 2: 
-		return OVERDRIVE_PCI_IRQ1;
-	case 3:
-		/* Note this assumes you have a hacked card in slot 2 */
-		return OVERDRIVE_PCI_IRQ2;
-	case 4:
-		return OVERDRIVE_ESS_IRQ;
-	default:
-		/* printk("PCI: Unexpected IRQ mapping request for slot %d\n", slot); */
-		return -1;
-	}
-}
-
-
-
-void __init
-pcibios_fixup_pbus_ranges(struct pci_bus *bus, struct pbus_set_ranges_data *ranges)
-{
-        ranges->io_start -= bus->resource[0]->start;
-        ranges->io_end -= bus->resource[0]->start;
-        ranges->mem_start -= bus->resource[1]->start;
-        ranges->mem_end -= bus->resource[1]->start;
-}                                                                                
-
-static void __init pci_fixup_ide_bases(struct pci_dev *d)
-{
-	int i;
-
-	/*
-	 * PCI IDE controllers use non-standard I/O port decoding, respect it.
-	 */
-	if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE)
-		return;
-	printk("PCI: IDE base address fixup for %s\n", pci_name(d));
-	for(i=0; i<4; i++) {
-		struct resource *r = &d->resource[i];
-		if ((r->start & ~0x80) == 0x374) {
-			r->start |= 2;
-			r->end = r->start;
-		}
-	}
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases);
-
-void __init pcibios_init(void)
-{
-	static struct resource galio,galmem;
-
-        /* Allocate the registers used by the Galileo */
-        galio.flags = IORESOURCE_IO;
-        galio.name  = "Galileo GT64011";
-        galmem.flags = IORESOURCE_MEM|IORESOURCE_PREFETCH;
-        galmem.name  = "Galileo GT64011 DRAM";
-
-        allocate_resource(&ioport_resource, &galio, 256,
-		    GT64111_IO_BASE_ADDRESS,GT64111_IO_BASE_ADDRESS+256, 256, NULL, NULL);
-        allocate_resource(&iomem_resource, &galmem,PCI_DRAM_SIZE,
-		    PHYSADDR(PCI_DRAM_BASE), PHYSADDR(PCI_DRAM_BASE)+PCI_DRAM_SIZE, 
-			     PCI_DRAM_SIZE, NULL, NULL);
-
-  	/* ok, do the scan man */
-	pci_root_bus = pci_scan_bus(0, &pci_config_ops, NULL);
-
-        pci_assign_unassigned_resources();
-	pci_fixup_irqs(no_swizzle, map_od_irq);
-
-#ifdef TEST_DRAM
-        printk("Testing PCI DRAM - ");
-	if(test_dram(PCI_DRAM_BASE,PCI_DRAM_SIZE)) {
-		printk("Passed\n");
-	}else {
-		printk("FAILED\n");
-	}
-#endif
-
-}
-
-char * __init pcibios_setup(char *str)
-{
-	return str;
-}
-
-
-
-int pcibios_enable_device(struct pci_dev *dev)
-{
-
-	u16 cmd, old_cmd;
-	int idx;
-	struct resource *r;
-
-	pci_read_config_word(dev, PCI_COMMAND, &cmd);
-	old_cmd = cmd;
-	for (idx = 0; idx < 6; idx++) {
-		r = dev->resource + idx;
-		if (!r->start && r->end) {
-			printk(KERN_ERR
-			       "PCI: Device %s not available because"
-			       " of resource collisions\n",
-			       pci_name(dev));
-			return -EINVAL;
-		}
-		if (r->flags & IORESOURCE_IO)
-			cmd |= PCI_COMMAND_IO;
-		if (r->flags & IORESOURCE_MEM)
-			cmd |= PCI_COMMAND_MEMORY;
-	}
-	if (cmd != old_cmd) {
-		printk("PCI: enabling device %s (%04x -> %04x)\n",
-		       pci_name(dev), old_cmd, cmd);
-		pci_write_config_word(dev, PCI_COMMAND, cmd);
-	}
-	return 0;
-
-}
-
-/* We should do some optimisation work here I think. Ok for now though */
-void __init pcibios_fixup_bus(struct pci_bus *bus)
-{
-
-}
-
-void pcibios_align_resource(void *data, struct resource *res,
-			    resource_size_t size)
-{
-}
-
-void __init pcibios_update_resource(struct pci_dev *dev, struct resource *root,
-			     struct resource *res, int resource)
-{
-
-	unsigned long where, size;
-	u32 reg;
-	
-
-	printk("PCI: Assigning %3s %08lx to %s\n",
-	       res->flags & IORESOURCE_IO ? "IO" : "MEM",
-	       res->start, dev->name);
-
-	where = PCI_BASE_ADDRESS_0 + resource * 4;
-	size = res->end - res->start;
-
-	pci_read_config_dword(dev, where, &reg);
-	reg = (reg & size) | (((u32) (res->start - root->start)) & ~size);
-	pci_write_config_dword(dev, where, reg);
-}
-
-
-void __init pcibios_update_irq(struct pci_dev *dev, int irq)
-{
-	printk("PCI: Assigning IRQ %02d to %s\n", irq, dev->name);
-	pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq);
-}
-
-/*
- *  If we set up a device for bus mastering, we need to check the latency
- *  timer as certain crappy BIOSes forget to set it properly.
- */
-unsigned int pcibios_max_latency = 255;
-
-void pcibios_set_master(struct pci_dev *dev)
-{
-	u8 lat;
-	pci_read_config_byte(dev, PCI_LATENCY_TIMER, &lat);
-	if (lat < 16)
-		lat = (64 <= pcibios_max_latency) ? 64 : pcibios_max_latency;
-	else if (lat > pcibios_max_latency)
-		lat = pcibios_max_latency;
-	else
-		return;
-	printk("PCI: Setting latency timer of device %s to %d\n", pci_name(dev), lat);
-	pci_write_config_byte(dev, PCI_LATENCY_TIMER, lat);
-}
diff --git a/arch/sh/boards/overdrive/io.c b/arch/sh/boards/overdrive/io.c
deleted file mode 100644
index 4671b6b..0000000
--- a/arch/sh/boards/overdrive/io.c
+++ /dev/null
@@ -1,172 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * This file contains the I/O routines for use on the overdrive board
- *
- */
-
-#include <linux/types.h>
-#include <linux/delay.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/addrspace.h>
-
-#include <asm/overdrive/overdrive.h>
-
-/*
- * readX/writeX() are used to access memory mapped devices. On some
- * architectures the memory mapped IO stuff needs to be accessed
- * differently. On the SuperH architecture, we just read/write the
- * memory location directly.
- */
-
-#define dprintk(x...)
-
-/* Translates an IO address to where it is mapped in memory */
-
-#define io_addr(x) (((unsigned)(x))|PCI_GTIO_BASE)
-
-unsigned char od_inb(unsigned long port)
-{
-dprintk("od_inb(%x)\n", port);
-	return readb(io_addr(port)) & 0xff;
-}
-
-
-unsigned short od_inw(unsigned long port)
-{
-dprintk("od_inw(%x)\n", port);
-	return readw(io_addr(port)) & 0xffff;
-}
-
-unsigned int od_inl(unsigned long port)
-{
-dprintk("od_inl(%x)\n", port);
-	return readl(io_addr(port));
-}
-
-void od_outb(unsigned char value, unsigned long port)
-{
-dprintk("od_outb(%x, %x)\n", value, port);
-	writeb(value, io_addr(port));
-}
-
-void od_outw(unsigned short value, unsigned long port)
-{
-dprintk("od_outw(%x, %x)\n", value, port);
-	writew(value, io_addr(port));
-}
-
-void od_outl(unsigned int value, unsigned long port)
-{
-dprintk("od_outl(%x, %x)\n", value, port);
-	writel(value, io_addr(port));
-}
-
-/* This is horrible at the moment - needs more work to do something sensible */
-#define IO_DELAY() udelay(10)
-
-#define OUT_DELAY(x,type) \
-void od_out##x##_p(unsigned type value,unsigned long port){out##x(value,port);IO_DELAY();}
-
-#define IN_DELAY(x,type) \
-unsigned type od_in##x##_p(unsigned long port) {unsigned type tmp=in##x(port);IO_DELAY();return tmp;}
-
-
-OUT_DELAY(b,char)
-OUT_DELAY(w,short)
-OUT_DELAY(l,int)
-
-IN_DELAY(b,char)
-IN_DELAY(w,short)
-IN_DELAY(l,int)
-
-
-/*  Now for the string version of these functions */
-void od_outsb(unsigned long port, const void *addr, unsigned long count)
-{
-	int i;
-	unsigned char *p = (unsigned char *) addr;
-
-	for (i = 0; i < count; i++, p++) {
-		outb(*p, port);
-	}
-}
-
-
-void od_insb(unsigned long port, void *addr, unsigned long count)
-{
-	int i;
-	unsigned char *p = (unsigned char *) addr;
-
-	for (i = 0; i < count; i++, p++) {
-		*p = inb(port);
-	}
-}
-
-/* For the 16 and 32 bit string functions, we have to worry about alignment.
- * The SH does not do unaligned accesses, so we have to read as bytes and
- * then write as a word or dword. 
- * This can be optimised a lot more, especially in the case where the data
- * is aligned
- */
-
-void od_outsw(unsigned long port, const void *addr, unsigned long count)
-{
-	int i;
-	unsigned short tmp;
-	unsigned char *p = (unsigned char *) addr;
-
-	for (i = 0; i < count; i++, p += 2) {
-		tmp = (*p) | ((*(p + 1)) << 8);
-		outw(tmp, port);
-	}
-}
-
-
-void od_insw(unsigned long port, void *addr, unsigned long count)
-{
-	int i;
-	unsigned short tmp;
-	unsigned char *p = (unsigned char *) addr;
-
-	for (i = 0; i < count; i++, p += 2) {
-		tmp = inw(port);
-		p[0] = tmp & 0xff;
-		p[1] = (tmp >> 8) & 0xff;
-	}
-}
-
-
-void od_outsl(unsigned long port, const void *addr, unsigned long count)
-{
-	int i;
-	unsigned tmp;
-	unsigned char *p = (unsigned char *) addr;
-
-	for (i = 0; i < count; i++, p += 4) {
-		tmp = (*p) | ((*(p + 1)) << 8) | ((*(p + 2)) << 16) |
-		      ((*(p + 3)) << 24);
-		outl(tmp, port);
-	}
-}
-
-
-void od_insl(unsigned long port, void *addr, unsigned long count)
-{
-	int i;
-	unsigned tmp;
-	unsigned char *p = (unsigned char *) addr;
-
-	for (i = 0; i < count; i++, p += 4) {
-		tmp = inl(port);
-		p[0] = tmp & 0xff;
-		p[1] = (tmp >> 8) & 0xff;
-		p[2] = (tmp >> 16) & 0xff;
-		p[3] = (tmp >> 24) & 0xff;
-
-	}
-}
diff --git a/arch/sh/boards/overdrive/irq.c b/arch/sh/boards/overdrive/irq.c
deleted file mode 100644
index 5d730c7..0000000
--- a/arch/sh/boards/overdrive/irq.c
+++ /dev/null
@@ -1,191 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * Looks after interrupts on the overdrive board.
- *
- * Bases on the IPR irq system
- */
-
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-
-#include <asm/overdrive/overdrive.h>
-
-struct od_data {
-	int overdrive_irq;
-	int irq_mask;
-};
-
-#define NUM_EXTERNAL_IRQS 16
-#define EXTERNAL_IRQ_NOT_IN_USE (-1)
-#define EXTERNAL_IRQ_NOT_ASSIGNED (-1)
-
-/*
- * This table is used to determine what to program into the FPGA's CT register
- * for the specified Linux IRQ.
- *
- * The irq_mask gives the interrupt number from the PCI board (PCI_Int(6:0))
- * but is one greater than that because the because the FPGA treats 0
- * as disabled, a value of 1 asserts PCI_Int0, and so on.
- *
- * The overdrive_irq specifies which of the eight interrupt sources generates
- * that interrupt, and but is multiplied by four to give the bit offset into
- * the CT register.
- *
- * The seven interrupts levels (SH4 IRL's) we have available here is hardwired
- * by the EPLD. The assignments here of which PCI interrupt generates each
- * level is arbitary.
- */
-static struct od_data od_data_table[NUM_EXTERNAL_IRQS] = {
-	/*    overdrive_irq       , irq_mask */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 0 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 7},	/* 1 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 6},	/* 2 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 3 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 5},	/* 4 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 5 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 6 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 4},	/* 7 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 8 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 9 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 3},	/* 10 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 2},	/* 11 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 12 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, 1},	/* 13 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE},	/* 14 */
-	{EXTERNAL_IRQ_NOT_ASSIGNED, EXTERNAL_IRQ_NOT_IN_USE}	/* 15 */
-};
-
-static void set_od_data(int overdrive_irq, int irq)
-{
-	if (irq >= NUM_EXTERNAL_IRQS || irq < 0)
-		return;
-	od_data_table[irq].overdrive_irq = overdrive_irq << 2;
-}
-
-static void enable_od_irq(unsigned int irq);
-void disable_od_irq(unsigned int irq);
-
-/* shutdown is same as "disable" */
-#define shutdown_od_irq disable_od_irq
-
-static void mask_and_ack_od(unsigned int);
-static void end_od_irq(unsigned int irq);
-
-static unsigned int startup_od_irq(unsigned int irq)
-{
-	enable_od_irq(irq);
-	return 0;		/* never anything pending */
-}
-
-static struct hw_interrupt_type od_irq_type = {
-	.typename = "Overdrive-IRQ",
-	.startup = startup_od_irq,
-	.shutdown = shutdown_od_irq,
-	.enable = enable_od_irq,
-	.disable = disable_od_irq,
-	.ack = mask_and_ack_od,
-	.end = end_od_irq
-};
-
-static void disable_od_irq(unsigned int irq)
-{
-	unsigned val, flags;
-	int overdrive_irq;
-	unsigned mask;
-
-	/* Not a valid interrupt */
-	if (irq < 0 || irq >= NUM_EXTERNAL_IRQS)
-		return;
-
-        /* Is is necessary to use a cli here? Would a spinlock not be 
-         * mroe efficient?
-         */
-	local_irq_save(flags);
-	overdrive_irq = od_data_table[irq].overdrive_irq;
-	if (overdrive_irq != EXTERNAL_IRQ_NOT_ASSIGNED) {
-		mask = ~(0x7 << overdrive_irq);
-		val = ctrl_inl(OVERDRIVE_INT_CT);
-		val &= mask;
-		ctrl_outl(val, OVERDRIVE_INT_CT);
-	}
-	local_irq_restore(flags);
-}
-
-static void enable_od_irq(unsigned int irq)
-{
-	unsigned val, flags;
-	int overdrive_irq;
-	unsigned mask;
-
-	/* Not a valid interrupt */
-	if (irq < 0 || irq >= NUM_EXTERNAL_IRQS)
-		return;
-
-	/* Set priority in OD back to original value */
-	local_irq_save(flags);
-	/* This one is not in use currently */
-	overdrive_irq = od_data_table[irq].overdrive_irq;
-	if (overdrive_irq != EXTERNAL_IRQ_NOT_ASSIGNED) {
-		val = ctrl_inl(OVERDRIVE_INT_CT);
-		mask = ~(0x7 << overdrive_irq);
-		val &= mask;
-		mask = od_data_table[irq].irq_mask << overdrive_irq;
-		val |= mask;
-		ctrl_outl(val, OVERDRIVE_INT_CT);
-	}
-	local_irq_restore(flags);
-}
-
-
-
-/* this functions sets the desired irq handler to be an overdrive type */
-static void __init make_od_irq(unsigned int irq)
-{
-	disable_irq_nosync(irq);
-	irq_desc[irq].chip = &od_irq_type;
-	disable_od_irq(irq);
-}
-
-
-static void mask_and_ack_od(unsigned int irq)
-{
-	disable_od_irq(irq);
-}
-
-static void end_od_irq(unsigned int irq)
-{
-	enable_od_irq(irq);
-}
-
-void __init init_overdrive_irq(void)
-{
-	int i;
-
-	/* Disable all interrupts */
-	ctrl_outl(0, OVERDRIVE_INT_CT);
-
-	/* Update interrupt pin mode to use encoded interrupts */
-	i = ctrl_inw(INTC_ICR);
-	i &= ~INTC_ICR_IRLM;
-	ctrl_outw(i, INTC_ICR);
-
-	for (i = 0; i < NUM_EXTERNAL_IRQS; i++) {
-		if (od_data_table[i].irq_mask != EXTERNAL_IRQ_NOT_IN_USE) {
-			make_od_irq(i);
-		} else if (i != 15) {	// Cannot use imask on level 15
-			make_imask_irq(i);
-		}
-	}
-
-	/* Set up the interrupts */
-	set_od_data(OVERDRIVE_PCI_INTA, OVERDRIVE_PCI_IRQ1);
-	set_od_data(OVERDRIVE_PCI_INTB, OVERDRIVE_PCI_IRQ2);
-	set_od_data(OVERDRIVE_AUDIO_INT, OVERDRIVE_ESS_IRQ);
-}
diff --git a/arch/sh/boards/overdrive/led.c b/arch/sh/boards/overdrive/led.c
deleted file mode 100644
index 860d7f2..0000000
--- a/arch/sh/boards/overdrive/led.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * linux/arch/sh/overdrive/led.c
- *
- * Copyright (C) 1999 Stuart Menefy <stuart.menefy@st.com>
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * This file contains an Overdrive specific LED feature.
- */
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/overdrive/overdrive.h>
-
-static void mach_led(int position, int value)
-{
-	unsigned long flags;
-	unsigned long reg;
-
-	local_irq_save(flags);
-	
-	reg = readl(OVERDRIVE_CTRL);
-	if (value) {
-		reg |= (1<<3);
-	} else {
-		reg &= ~(1<<3);
-	}
-	writel(reg, OVERDRIVE_CTRL);
-
-	local_irq_restore(flags);
-}
-
-#ifdef CONFIG_HEARTBEAT
-
-#include <linux/sched.h>
-
-/* acts like an actual heart beat -- ie thump-thump-pause... */
-void heartbeat_od(void)
-{
-	static unsigned cnt = 0, period = 0, dist = 0;
-
-	if (cnt == 0 || cnt == dist)
-		mach_led( -1, 1);
-	else if (cnt == 7 || cnt == dist+7)
-		mach_led( -1, 0);
-
-	if (++cnt > period) {
-		cnt = 0;
-		/* The hyperbolic function below modifies the heartbeat period
-		 * length in dependency of the current (5min) load. It goes
-		 * through the points f(0)=126, f(1)=86, f(5)=51,
-		 * f(inf)->30. */
-		period = ((672<<FSHIFT)/(5*avenrun[0]+(7<<FSHIFT))) + 30;
-		dist = period / 4;
-	}
-}
-#endif /* CONFIG_HEARTBEAT */
diff --git a/arch/sh/boards/overdrive/mach.c b/arch/sh/boards/overdrive/mach.c
deleted file mode 100644
index 2834a03..0000000
--- a/arch/sh/boards/overdrive/mach.c
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
- * linux/arch/sh/overdrive/mach.c
- *
- * Copyright (C) 2000 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * Machine vector for the STMicroelectronics Overdrive
- */
-
-#include <linux/init.h>
-
-#include <asm/machvec.h>
-#include <asm/rtc.h>
-#include <asm/machvec_init.h>
-
-#include <asm/io_unknown.h>
-#include <asm/io_generic.h>
-#include <asm/overdrive/io.h>
-
-void heartbeat_od(void);
-void init_overdrive_irq(void);
-void galileo_pcibios_init(void);
-
-/*
- * The Machine Vector
- */
-
-struct sh_machine_vector mv_od __initmv = {
-	.mv_nr_irqs		= 48,
-
-	.mv_inb			= od_inb,
-	.mv_inw			= od_inw,
-	.mv_inl			= od_inl,
-	.mv_outb		= od_outb,
-	.mv_outw		= od_outw,
-	.mv_outl		= od_outl,
-
-	.mv_inb_p		= od_inb_p,
-	.mv_inw_p		= od_inw_p,
-	.mv_inl_p		= od_inl_p,
-	.mv_outb_p		= od_outb_p,
-	.mv_outw_p		= od_outw_p,
-	.mv_outl_p		= od_outl_p,
-
-	.mv_insb		= od_insb,
-	.mv_insw		= od_insw,
-	.mv_insl		= od_insl,
-	.mv_outsb		= od_outsb,
-	.mv_outsw		= od_outsw,
-	.mv_outsl		= od_outsl,
-
-#ifdef CONFIG_PCI
-	.mv_init_irq		= init_overdrive_irq,
-#endif
-#ifdef CONFIG_HEARTBEAT
-	.mv_heartbeat		= heartbeat_od,
-#endif
-};
-
-ALIAS_MV(od)
diff --git a/arch/sh/boards/overdrive/pcidma.c b/arch/sh/boards/overdrive/pcidma.c
deleted file mode 100644
index 1c9bfed..0000000
--- a/arch/sh/boards/overdrive/pcidma.c
+++ /dev/null
@@ -1,46 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * Dynamic DMA mapping support.
- *
- * On the overdrive, we can only DMA from memory behind the PCI bus!
- * this means that all DMA'able memory must come from there. 
- * this restriction will not apply to later boards.
- */
-
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/string.h>
-#include <linux/pci.h>
-#include <asm/io.h>
-
-void *pci_alloc_consistent(struct pci_dev *hwdev, size_t size,
-			   dma_addr_t * dma_handle)
-{
-	void *ret;
-	int gfp = GFP_ATOMIC;
-
-        printk("BUG: pci_alloc_consistent() called - not yet supported\n");
-	/* We ALWAYS need DMA memory on the overdrive hardware,
-	 * due to it's extreme weirdness
-	 * Need to flush the cache here as well, since the memory
-	 * can still be seen through the cache!
-	 */
-	gfp |= GFP_DMA;
-	ret = (void *) __get_free_pages(gfp, get_order(size));
-
-	if (ret != NULL) {
-		memset(ret, 0, size);
-		*dma_handle = virt_to_bus(ret);
-	}
-	return ret;
-}
-
-void pci_free_consistent(struct pci_dev *hwdev, size_t size,
-			 void *vaddr, dma_addr_t dma_handle)
-{
-	free_pages((unsigned long) vaddr, get_order(size));
-}
diff --git a/arch/sh/boards/overdrive/setup.c b/arch/sh/boards/overdrive/setup.c
deleted file mode 100644
index a3a7744..0000000
--- a/arch/sh/boards/overdrive/setup.c
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * arch/sh/overdrive/setup.c
- *
- * Copyright (C) 2000 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * STMicroelectronics Overdrive Support.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <asm/io.h>
-
-#include <asm/overdrive/overdrive.h>
-#include <asm/overdrive/fpga.h>
-
-const char *get_system_type(void)
-{
-	return "SH7750 Overdrive";
-}
-
-/*
- * Initialize the board
- */
-int __init platform_setup(void)
-{
-#ifdef CONFIG_PCI
-	init_overdrive_fpga();
-	galileo_init();
-#endif
-
-        /* Enable RS232 receive buffers */
-	writel(0x1e, OVERDRIVE_CTRL);
-}
diff --git a/arch/sh/boards/sh2000/Makefile b/arch/sh/boards/sh2000/Makefile
deleted file mode 100644
index 05d390c..0000000
--- a/arch/sh/boards/sh2000/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-# Makefile for the SH2000 specific parts of the kernel
-#
-
-obj-y	 := setup.o
-
diff --git a/arch/sh/boards/sh2000/setup.c b/arch/sh/boards/sh2000/setup.c
deleted file mode 100644
index 2fe6a11..0000000
--- a/arch/sh/boards/sh2000/setup.c
+++ /dev/null
@@ -1,70 +0,0 @@
-/*
- * linux/arch/sh/kernel/setup_sh2000.c
- *
- * Copyright (C) 2001  SUGIOKA Tochinobu
- *
- * SH-2000 Support.
- *
- */
-
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/io.h>
-#include <asm/machvec.h>
-#include <asm/mach/sh2000.h>
-
-#define CF_CIS_BASE	0xb4200000
-
-#define PORT_PECR	0xa4000108
-#define PORT_PHCR	0xa400010E
-#define	PORT_ICR1	0xa4000010
-#define	PORT_IRR0	0xa4000004
-
-#define IDE_OFFSET	0xb6200000
-#define NIC_OFFSET	0xb6000000
-#define EXTBUS_OFFSET	0xba000000
-
-
-const char *get_system_type(void)
-{
-	return "sh2000";
-}
-
-static unsigned long sh2000_isa_port2addr(unsigned long offset)
-{
-	if((offset & ~7) == 0x1f0 || offset == 0x3f6)
-		return IDE_OFFSET + offset;
-	else if((offset & ~0x1f) == 0x300)
-		return NIC_OFFSET + offset;
-	return EXTBUS_OFFSET + offset;
-}
-
-/*
- * The Machine Vector
- */
-struct sh_machine_vector mv_sh2000 __initmv = {
-        .mv_nr_irqs		= 80,
-        .mv_isa_port2addr	= sh2000_isa_port2addr,
-};
-ALIAS_MV(sh2000)
-
-/*
- * Initialize the board
- */
-int __init platform_setup(void)
-{
-	/* XXX: RTC setting comes here */
-
-	/* These should be done by BIOS/IPL ... */
-	/* Enable nCE2A, nCE2B output */
-	ctrl_outw(ctrl_inw(PORT_PECR) & ~0xf00, PORT_PECR);
-	/* Enable the Compact Flash card, and set the level interrupt */
-	ctrl_outw(0x0042, CF_CIS_BASE+0x0200);
-	/* Enable interrupt */
-	ctrl_outw(ctrl_inw(PORT_PHCR) & ~0x03f3, PORT_PHCR);
-	ctrl_outw(1, PORT_ICR1);
-	ctrl_outw(ctrl_inw(PORT_IRR0) & ~0xff3f, PORT_IRR0);
-	printk(KERN_INFO "SH-2000 Setup...done\n");
-	return 0;
-}
diff --git a/arch/sh/tools/mach-types b/arch/sh/tools/mach-types
index ffd2180..b30e784 100644
--- a/arch/sh/tools/mach-types
+++ b/arch/sh/tools/mach-types
@@ -13,11 +13,9 @@
 HP6XX			SH_HP6XX
 HD64461			HD64461
 HD64465			HD64465
-SH2000			SH_SH2000
 SATURN			SH_SATURN
 DREAMCAST		SH_DREAMCAST
 BIGSUR			SH_BIGSUR
-ADX			SH_ADX
 MPC1211			SH_MPC1211
 SNAPGEAR		SH_SECUREEDGE5410
 HS7751RVOIP		SH_HS7751RVOIP
diff --git a/include/asm-sh/adx/io.h b/include/asm-sh/adx/io.h
deleted file mode 100644
index ab1225f..0000000
--- a/include/asm-sh/adx/io.h
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * include/asm-sh/io_adx.h
- *
- * Copyright (C) 2001 A&D Co., Ltd.
- *
- * This file may be copied or modified under the terms of the GNU
- * General Public License.  See linux/COPYING for more information.
- *
- * IO functions for an A&D ADX Board
- */
-
-#ifndef _ASM_SH_IO_ADX_H
-#define _ASM_SH_IO_ADX_H
-
-#include <asm/io_generic.h>
-
-extern unsigned char adx_inb(unsigned long port);
-extern unsigned short adx_inw(unsigned long port);
-extern unsigned int adx_inl(unsigned long port);
-
-extern void adx_outb(unsigned char value, unsigned long port);
-extern void adx_outw(unsigned short value, unsigned long port);
-extern void adx_outl(unsigned int value, unsigned long port);
-
-extern unsigned char adx_inb_p(unsigned long port);
-extern void adx_outb_p(unsigned char value, unsigned long port);
-
-extern void adx_insb(unsigned long port, void *addr, unsigned long count);
-extern void adx_insw(unsigned long port, void *addr, unsigned long count);
-extern void adx_insl(unsigned long port, void *addr, unsigned long count);
-extern void adx_outsb(unsigned long port, const void *addr, unsigned long count);
-extern void adx_outsw(unsigned long port, const void *addr, unsigned long count);
-extern void adx_outsl(unsigned long port, const void *addr, unsigned long count);
-
-extern unsigned char adx_readb(unsigned long addr);
-extern unsigned short adx_readw(unsigned long addr);
-extern unsigned int adx_readl(unsigned long addr);
-extern void adx_writeb(unsigned char b, unsigned long addr);
-extern void adx_writew(unsigned short b, unsigned long addr);
-extern void adx_writel(unsigned int b, unsigned long addr);
-
-extern void * adx_ioremap(unsigned long offset, unsigned long size);
-extern void adx_iounmap(void *addr);
-
-extern unsigned long adx_isa_port2addr(unsigned long offset);
-
-extern void setup_adx(void);
-extern void init_adx_IRQ(void);
-
-#ifdef __WANT_IO_DEF
-
-#define __inb		adx_inb
-#define __inw		adx_inw
-#define __inl		adx_inl
-#define __outb		adx_outb
-#define __outw		adx_outw
-#define __outl		adx_outl
-
-#define __inb_p		adx_inb_p
-#define __inw_p		adx_inw
-#define __inl_p		adx_inl
-#define __outb_p	adx_outb_p
-#define __outw_p	adx_outw
-#define __outl_p	adx_outl
-
-#define __insb		adx_insb
-#define __insw		adx_insw
-#define __insl		adx_insl
-#define __outsb		adx_outsb
-#define __outsw		adx_outsw
-#define __outsl		adx_outsl
-
-#define __readb		adx_readb
-#define __readw		adx_readw
-#define __readl		adx_readl
-#define __writeb	adx_writeb
-#define __writew	adx_writew
-#define __writel	adx_writel
-
-#define __isa_port2addr	adx_isa_port2addr
-#define __ioremap	adx_ioremap
-#define __iounmap	adx_iounmap
-
-#endif
-
-#endif /* _ASM_SH_IO_AANDD_H */
diff --git a/include/asm-sh/cat68701/io.h b/include/asm-sh/cat68701/io.h
deleted file mode 100644
index 753b846..0000000
--- a/include/asm-sh/cat68701/io.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * include/asm-sh/io_cat68701.h
- *
- * Copyright 2000 Stuart Menefy (stuart.menefy@st.com)
- *           2001 Yutarou Ebihar (ebihara@si-linux.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * IO functions for an AONE Corp. CAT-68701 SH7708 Borad
- */
-
-#ifndef _ASM_SH_IO_CAT68701_H
-#define _ASM_SH_IO_CAT68701_H
-
-extern unsigned long cat68701_isa_port2addr(unsigned long offset);
-extern int cat68701_irq_demux(int irq);
-
-extern void init_cat68701_IRQ(void);
-extern void heartbeat_cat68701(void);
-
-#endif /* _ASM_SH_IO_CAT68701_H */
diff --git a/include/asm-sh/cqreek/cqreek.h b/include/asm-sh/cqreek/cqreek.h
deleted file mode 100644
index 09aecc0..0000000
--- a/include/asm-sh/cqreek/cqreek.h
+++ /dev/null
@@ -1,27 +0,0 @@
-#ifndef __ASM_SH_CQREEK_CQREEK_H
-#define __ASM_SH_CQREEK_CQREEK_H
-
-#define BRIDGE_FEATURE		0x0002
-
-#define BRIDGE_IDE_CTRL		0x0018
-#define BRIDGE_IDE_INTR_LVL    	0x001A
-#define BRIDGE_IDE_INTR_MASK	0x001C
-#define BRIDGE_IDE_INTR_STAT	0x001E
-
-#define BRIDGE_ISA_CTRL		0x0028
-#define BRIDGE_ISA_INTR_LVL    	0x002A
-#define BRIDGE_ISA_INTR_MASK	0x002C
-#define BRIDGE_ISA_INTR_STAT	0x002E
-
-/* arch/sh/boards/cqreek/setup.c */
-extern void setup_cqreek(void);
-
-/* arch/sh/boards/cqreek/irq.c */
-extern int cqreek_has_ide, cqreek_has_isa;
-extern void init_cqreek_IRQ(void);
-
-/* arch/sh/boards/cqreek/io.c */
-extern unsigned long cqreek_port2addr(unsigned long port);
-
-#endif /* __ASM_SH_CQREEK_CQREEK_H */
-
diff --git a/include/asm-sh/dmida/io.h b/include/asm-sh/dmida/io.h
deleted file mode 100644
index 21bd416..0000000
--- a/include/asm-sh/dmida/io.h
+++ /dev/null
@@ -1,10 +0,0 @@
-#ifndef __ASM_SH_DMIDA_IO_H
-#define __ASM_SH_DMIDA_IO_H
-
-/*
- * Nothing special here.. just use the generic cchip io routines.
- */
-#include <asm/hd64465/io.h>
-
-#endif /* __ASM_SH_DMIDA_IO_H */
-
diff --git a/include/asm-sh/harp/harp.h b/include/asm-sh/harp/harp.h
deleted file mode 100644
index b2fbcfa..0000000
--- a/include/asm-sh/harp/harp.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/* 
- * Copyright (C) 2001 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- * Defintions applicable to the STMicroelectronics ST40STB1 HARP and
- * compatible boards.
- */
-
-#if defined(CONFIG_SH_STB1_HARP)
-
-#define EPLD_BASE     0xa0800000
-
-#define EPLD_LED      (EPLD_BASE+0x000c0000)
-#define EPLD_INTSTAT0 (EPLD_BASE+0x00200000)
-#define EPLD_INTSTAT1 (EPLD_BASE+0x00240000)
-#define EPLD_INTMASK0 (EPLD_BASE+0x00280000)
-#define EPLD_INTMASK1 (EPLD_BASE+0x002c0000)
-#define EPLD_PAGEADDR (EPLD_BASE+0x00300000)
-#define EPLD_REVID1   (EPLD_BASE+0x00380000)
-#define EPLD_REVID2   (EPLD_BASE+0x003c0000)
-
-#define EPLD_LED_ON  1
-#define EPLD_LED_OFF 0
-
-#elif defined(CONFIG_SH_STB1_OVERDRIVE)
-
-#define EPLD_BASE     0xa7000000
-
-#define EPLD_REVID    (EPLD_BASE+0x00000000)
-#define EPLD_LED      (EPLD_BASE+0x00040000)
-#define EPLD_INTMASK0 (EPLD_BASE+0x001c0000)
-#define EPLD_INTMASK1 (EPLD_BASE+0x00200000)
-#define EPLD_INTSTAT0 (EPLD_BASE+0x00240000)
-#define EPLD_INTSTAT1 (EPLD_BASE+0x00280000)
-
-#define EPLD_LED_ON  0
-#define EPLD_LED_OFF 1
-
-#else
-#error Unknown board
-#endif
diff --git a/include/asm-sh/harp/io.h b/include/asm-sh/harp/io.h
deleted file mode 100644
index 68f39e0..0000000
--- a/include/asm-sh/harp/io.h
+++ /dev/null
@@ -1,10 +0,0 @@
-#ifndef __ASM_SH_HARP_IO_H
-#define __ASM_SH_HARP_IO_H
-
-/*
- * Nothing special here.. just use the generic cchip io routines.
- */
-#include <asm/hd64465/io.h>
-
-#endif /* __ASM_SH_HARP_IO_H */
-
diff --git a/include/asm-sh/overdrive/fpga.h b/include/asm-sh/overdrive/fpga.h
deleted file mode 100644
index 1cd8799..0000000
--- a/include/asm-sh/overdrive/fpga.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- */
-
-#ifndef __FPGA_OD_H__
-#define __FPGA_OD_H__
-
-/* This routine will program up the fpga which interfaces to the galileo */
-int init_overdrive_fpga(void);
-
-#endif
diff --git a/include/asm-sh/overdrive/gt64111.h b/include/asm-sh/overdrive/gt64111.h
deleted file mode 100644
index 01d58bc..0000000
--- a/include/asm-sh/overdrive/gt64111.h
+++ /dev/null
@@ -1,109 +0,0 @@
-#ifndef _GT64111_H_
-#define _GT64111_H_
-
-#define MASTER_INTERFACE         0x0
-#define RAS10_LO_DEC_ADR         0x8        
-#define RAS10_HI_DEC_ADR         0x10
-#define RAS32_LO_DEC_ADR         0x18
-#define RAS32_HI_DEC_ADR         0x20
-#define CS20_LO_DEC_ADR          0x28
-#define CS20_HI_DEC_ADR          0x30
-#define CS3_LO_DEC_ADR           0x38
-#define CS3_HI_DEC_ADR           0x40
-#define PCI_IO_LO_DEC_ADR        0x48
-#define PCI_IO_HI_DEC_ADR        0x50
-#define PCI_MEM0_LO_DEC_ADR      0x58
-#define PCI_MEM0_HI_DEC_ADR      0x60
-#define INTERNAL_SPACE_DEC       0x68
-#define BUS_ERR_ADR_LO_CPU       0x70
-#define READONLY0                0x78
-#define PCI_MEM1_LO_DEC_ADR      0x80
-#define PCI_MEM1_HI_DEC_ADR      0x88
-#define RAS0_LO_DEC_ADR          0x400   
-#define RAS0_HI_DEC_ADR          0x404
-#define RAS1_LO_DEC_ADR          0x408
-#define RAS1_HI_DEC_ADR          0x40c
-#define RAS2_LO_DEC_ADR          0x410
-#define RAS2_HI_DEC_ADR          0x414
-#define RAS3_LO_DEC_ADR          0x418
-#define RAS3_HI_DEC_ADR          0x41c
-#define DEV_CS0_LO_DEC_ADR       0x420
-#define DEV_CS0_HI_DEC_ADR       0x424
-#define DEV_CS1_LO_DEC_ADR       0x428
-#define DEV_CS1_HI_DEC_ADR       0x42c
-#define DEV_CS2_LO_DEC_ADR       0x430
-#define DEV_CS2_HI_DEC_ADR       0x434
-#define DEV_CS3_LO_DEC_ADR       0x438
-#define DEV_CS3_HI_DEC_ADR       0x43c
-#define DEV_BOOTCS_LO_DEC_ADR    0x440
-#define DEV_BOOTCS_HI_DEC_ADR    0x444
-#define DEV_ADR_DEC_ERR          0x470
-#define DRAM_CFG                 0x448   
-#define DRAM_BANK0_PARMS         0x44c   
-#define DRAM_BANK1_PARMS         0x450
-#define DRAM_BANK2_PARMS         0x454
-#define DRAM_BANK3_PARMS         0x458
-#define DEV_BANK0_PARMS          0x45c
-#define DEV_BANK1_PARMS          0x460
-#define DEV_BANK2_PARMS          0x464
-#define DEV_BANK3_PARMS          0x468
-#define DEV_BOOT_BANK_PARMS      0x46c
-#define CH0_DMA_BYTECOUNT        0x800
-#define CH1_DMA_BYTECOUNT        0x804
-#define CH2_DMA_BYTECOUNT        0x808
-#define CH3_DMA_BYTECOUNT        0x80c
-#define CH0_DMA_SRC_ADR          0x810
-#define CH1_DMA_SRC_ADR          0x814
-#define CH2_DMA_SRC_ADR          0x818
-#define CH3_DMA_SRC_ADR          0x81c
-#define CH0_DMA_DST_ADR          0x820
-#define CH1_DMA_DST_ADR          0x824
-#define CH2_DMA_DST_ADR          0x828
-#define CH3_DMA_DST_ADR          0x82c
-#define CH0_NEXT_REC_PTR         0x830
-#define CH1_NEXT_REC_PTR         0x834
-#define CH2_NEXT_REC_PTR         0x838
-#define CH3_NEXT_REC_PTR         0x83c
-#define CH0_CTRL                 0x840
-#define CH1_CTRL                 0x844
-#define CH2_CTRL                 0x848
-#define CH3_CTRL                 0x84c
-#define DMA_ARBITER              0x860
-#define TIMER0                   0x850
-#define TIMER1                   0x854
-#define TIMER2                   0x858
-#define TIMER3                   0x85c
-#define TIMER_CTRL               0x864
-#define PCI_CMD                  0xc00
-#define PCI_TIMEOUT              0xc04
-#define PCI_RAS10_BANK_SIZE      0xc08
-#define PCI_RAS32_BANK_SIZE      0xc0c
-#define PCI_CS20_BANK_SIZE       0xc10
-#define PCI_CS3_BANK_SIZE        0xc14
-#define PCI_SERRMASK             0xc28
-#define PCI_INTACK               0xc34
-#define PCI_BAR_EN               0xc3c
-#define PCI_CFG_ADR              0xcf8
-#define PCI_CFG_DATA             0xcfc
-#define PCI_INTCAUSE             0xc18
-#define PCI_MAST_MASK            0xc1c
-#define PCI_PCIMASK              0xc24
-#define BAR_ENABLE_ADR           0xc3c
-
-/* These are config registers, accessible via PCI space */
-#define PCI_CONFIG_RAS10_BASE_ADR   0x010
-#define PCI_CONFIG_RAS32_BASE_ADR   0x014
-#define PCI_CONFIG_CS20_BASE_ADR    0x018
-#define PCI_CONFIG_CS3_BASE_ADR     0x01c
-#define PCI_CONFIG_INT_REG_MM_ADR   0x020
-#define PCI_CONFIG_INT_REG_IO_ADR   0x024
-#define PCI_CONFIG_BOARD_VENDOR     0x02c
-#define PCI_CONFIG_ROM_ADR          0x030
-#define PCI_CONFIG_INT_PIN_LINE     0x03c
-
-
-
-
-
-#endif
-
diff --git a/include/asm-sh/overdrive/io.h b/include/asm-sh/overdrive/io.h
deleted file mode 100644
index 0dba700..0000000
--- a/include/asm-sh/overdrive/io.h
+++ /dev/null
@@ -1,39 +0,0 @@
-/*
- * include/asm-sh/io_od.h
- *
- * Copyright 2000 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * IO functions for an STMicroelectronics Overdrive
- */
-
-#ifndef _ASM_SH_IO_OD_H
-#define _ASM_SH_IO_OD_H
-
-extern unsigned char od_inb(unsigned long port);
-extern unsigned short od_inw(unsigned long port);
-extern unsigned int od_inl(unsigned long port);
-
-extern void od_outb(unsigned char value, unsigned long port);
-extern void od_outw(unsigned short value, unsigned long port);
-extern void od_outl(unsigned int value, unsigned long port);
-
-extern unsigned char od_inb_p(unsigned long port);
-extern unsigned short od_inw_p(unsigned long port);
-extern unsigned int od_inl_p(unsigned long port);
-extern void od_outb_p(unsigned char value, unsigned long port);
-extern void od_outw_p(unsigned short value, unsigned long port);
-extern void od_outl_p(unsigned int value, unsigned long port);
-
-extern void od_insb(unsigned long port, void *addr, unsigned long count);
-extern void od_insw(unsigned long port, void *addr, unsigned long count);
-extern void od_insl(unsigned long port, void *addr, unsigned long count);
-extern void od_outsb(unsigned long port, const void *addr, unsigned long count);
-extern void od_outsw(unsigned long port, const void *addr, unsigned long count);
-extern void od_outsl(unsigned long port, const void *addr, unsigned long count);
-
-extern unsigned long od_isa_port2addr(unsigned long offset);
-
-#endif /* _ASM_SH_IO_OD_H */
diff --git a/include/asm-sh/overdrive/overdrive.h b/include/asm-sh/overdrive/overdrive.h
deleted file mode 100644
index fc746c2..0000000
--- a/include/asm-sh/overdrive/overdrive.h
+++ /dev/null
@@ -1,88 +0,0 @@
-/* 
- * Copyright (C) 2000 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.                            
- *
- */
-
-
-#ifndef __OVERDRIVE_H__
-#define __OVERDRIVE_H__
-
-#define OVERDRIVE_INT_CT 0xa3a00000
-#define OVERDRIVE_INT_DT 0xa3b00000
-
-#define OVERDRIVE_CTRL    0xa3000000
-
-/* Shoving all these bits into the same register is not a good idea. 
- * As soon as I get a spare moment, I'll change the FPGA and put each 
- * bit in a separate register
- */
-
-#define VALID_CTRL_BITS		          0x1f
-
-#define ENABLE_RS232_MASK	  	  0x1e
-#define DISABLE_RS232_BIT		  0x01
-
-#define ENABLE_NMI_MASK			  0x1d
-#define DISABLE_NMI_BIT			  0x02
-
-#define RESET_PCI_MASK			  0x1b
-#define ENABLE_PCI_BIT			  0x04
-
-#define ENABLE_LED_MASK			  0x17
-#define DISABLE_LED_BIT			  0x08
-
-#define RESET_FPGA_MASK			  0x0f
-#define ENABLE_FPGA_BIT			  0x10
-
-
-#define FPGA_DCLK_ADDRESS           0xA3C00000
-
-#define FPGA_DATA        0x01	/*   W */
-#define FPGA_CONFDONE    0x02	/* R   */
-#define FPGA_NOT_STATUS  0x04	/* R   */
-#define FPGA_INITDONE    0x08	/* R   */
-
-#define FPGA_TIMEOUT     100000
-
-
-/* Interrupts for the overdrive. Note that these numbers have 
- * nothing to do with the actual IRQ numbers they appear on, 
- * this is all programmable. This is simply the position in the 
- * INT_CT register.
- */
-
-#define OVERDRIVE_PCI_INTA              0
-#define OVERDRIVE_PCI_INTB              1
-#define OVERDRIVE_PCI_INTC              2
-#define OVERDRIVE_PCI_INTD              3
-#define OVERDRIVE_GALILEO_INT           4
-#define OVERDRIVE_GALILEO_LOCAL_INT     5
-#define OVERDRIVE_AUDIO_INT             6
-#define OVERDRIVE_KEYBOARD_INT          7
-
-/* Which Linux IRQ should we assign to each interrupt source? */
-#define OVERDRIVE_PCI_IRQ1              2
-#ifdef CONFIG_HACKED_NE2K
-#define OVERDRIVE_PCI_IRQ2              7
-#else
-#define OVERDRIVE_PCI_IRQ2              2
-#undef OVERDRIVE_PCI_INTB 
-#define OVERDRIVE_PCI_INTB OVERDRIVE_PCI_INTA
-
-#endif
-
-/* Put the ESS solo audio chip on IRQ 4 */
-#define OVERDRIVE_ESS_IRQ               4
-
-/* Where the memory behind the PCI bus appears */
-#define PCI_DRAM_BASE   0xb7000000
-#define PCI_DRAM_SIZE (16*1024*1024)
-#define PCI_DRAM_FINISH (PCI_DRAM_BASE+PCI_DRAM_SIZE-1)
-
-/* Where the IO region appears in the memory */
-#define PCI_GTIO_BASE   0xb8000000
-
-#endif
diff --git a/include/asm-sh/sh2000/sh2000.h b/include/asm-sh/sh2000/sh2000.h
deleted file mode 100644
index 8d54732..0000000
--- a/include/asm-sh/sh2000/sh2000.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#ifndef __ASM_SH_SH2000_SH2000_H
-#define __ASM_SH_SH2000_SH2000_H
-
-/* arch/sh/boards/sh2000/setup.c */
-extern int setup_sh2000(void);
-
-#endif /* __ASM_SH_SH2000_SH2000_H */
-