be2net: fix MAC address modification for VF
Currently, the VFs by default don't have the privilege to modify MAC address.
This will change in a subsequent fix wherein VFs will have the ability to
modify MAC/VLAN filters.
Fix be_mac_addr_set() logic to support MAC address modification on a
privileged VF too.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 181edb5..29e7870 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -247,54 +247,54 @@
static int be_mac_addr_set(struct net_device *netdev, void *p)
{
struct be_adapter *adapter = netdev_priv(netdev);
+ struct device *dev = &adapter->pdev->dev;
struct sockaddr *addr = p;
- int status = 0;
- u8 current_mac[ETH_ALEN];
- u32 pmac_id = adapter->pmac_id[0];
- bool active_mac = true;
+ int status;
+ u8 mac[ETH_ALEN];
+ u32 old_pmac_id = adapter->pmac_id[0], curr_pmac_id = 0;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
- /* For BE VF, MAC address is already activated by PF.
- * Hence only operation left is updating netdev->devaddr.
- * Update it if user is passing the same MAC which was used
- * during configuring VF MAC from PF(Hypervisor).
+ /* The PMAC_ADD cmd may fail if the VF doesn't have FILTMGMT
+ * privilege or if PF did not provision the new MAC address.
+ * On BE3, this cmd will always fail if the VF doesn't have the
+ * FILTMGMT privilege. This failure is OK, only if the PF programmed
+ * the MAC for the VF.
*/
- if (!lancer_chip(adapter) && !be_physfn(adapter)) {
- status = be_cmd_mac_addr_query(adapter, current_mac,
- false, adapter->if_handle, 0);
- if (!status && !memcmp(current_mac, addr->sa_data, ETH_ALEN))
- goto done;
- else
- goto err;
+ status = be_cmd_pmac_add(adapter, (u8 *)addr->sa_data,
+ adapter->if_handle, &adapter->pmac_id[0], 0);
+ if (!status) {
+ curr_pmac_id = adapter->pmac_id[0];
+
+ /* Delete the old programmed MAC. This call may fail if the
+ * old MAC was already deleted by the PF driver.
+ */
+ if (adapter->pmac_id[0] != old_pmac_id)
+ be_cmd_pmac_del(adapter, adapter->if_handle,
+ old_pmac_id, 0);
}
- if (!memcmp(addr->sa_data, netdev->dev_addr, ETH_ALEN))
- goto done;
-
- /* For Lancer check if any MAC is active.
- * If active, get its mac id.
+ /* Decide if the new MAC is successfully activated only after
+ * querying the FW
*/
- if (lancer_chip(adapter) && !be_physfn(adapter))
- be_cmd_get_mac_from_list(adapter, current_mac, &active_mac,
- &pmac_id, 0);
-
- status = be_cmd_pmac_add(adapter, (u8 *)addr->sa_data,
- adapter->if_handle,
- &adapter->pmac_id[0], 0);
-
+ status = be_cmd_get_active_mac(adapter, curr_pmac_id, mac);
if (status)
goto err;
- if (active_mac)
- be_cmd_pmac_del(adapter, adapter->if_handle,
- pmac_id, 0);
-done:
+ /* The MAC change did not happen, either due to lack of privilege
+ * or PF didn't pre-provision.
+ */
+ if (memcmp(addr->sa_data, mac, ETH_ALEN)) {
+ status = -EPERM;
+ goto err;
+ }
+
memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ dev_info(dev, "MAC address changed to %pM\n", mac);
return 0;
err:
- dev_err(&adapter->pdev->dev, "MAC %pM set Failed\n", addr->sa_data);
+ dev_warn(dev, "MAC address change to %pM failed\n", addr->sa_data);
return status;
}