[ARM] msm: Update list of proc_comm enums.
Signed-off-by: Dima Zavin <dima@android.com>
diff --git a/arch/arm/mach-msm/proc_comm.h b/arch/arm/mach-msm/proc_comm.h
index 834760f..2350765 100644
--- a/arch/arm/mach-msm/proc_comm.h
+++ b/arch/arm/mach-msm/proc_comm.h
@@ -62,19 +62,104 @@
PCOM_RESET_CHIP_IMM,
PCOM_PM_VID_EN,
PCOM_VREG_PULLDOWN,
+ PCOM_GET_MODEM_VERSION,
+ PCOM_CLK_REGIME_SEC_RESET,
+ PCOM_CLK_REGIME_SEC_RESET_ASSERT,
+ PCOM_CLK_REGIME_SEC_RESET_DEASSERT,
+ PCOM_CLK_REGIME_SEC_PLL_REQUEST_WRP,
+ PCOM_CLK_REGIME_SEC_ENABLE,
+ PCOM_CLK_REGIME_SEC_DISABLE,
+ PCOM_CLK_REGIME_SEC_IS_ON,
+ PCOM_CLK_REGIME_SEC_SEL_CLK_INV,
+ PCOM_CLK_REGIME_SEC_SEL_CLK_SRC,
+ PCOM_CLK_REGIME_SEC_SEL_CLK_DIV,
+ PCOM_CLK_REGIME_SEC_ICODEC_CLK_ENABLE,
+ PCOM_CLK_REGIME_SEC_ICODEC_CLK_DISABLE,
+ PCOM_CLK_REGIME_SEC_SEL_SPEED,
+ PCOM_CLK_REGIME_SEC_CONFIG_GP_CLK_WRP,
+ PCOM_CLK_REGIME_SEC_CONFIG_MDH_CLK_WRP,
+ PCOM_CLK_REGIME_SEC_USB_XTAL_ON,
+ PCOM_CLK_REGIME_SEC_USB_XTAL_OFF,
+ PCOM_CLK_REGIME_SEC_SET_QDSP_DME_MODE,
+ PCOM_CLK_REGIME_SEC_SWITCH_ADSP_CLK,
+ PCOM_CLK_REGIME_SEC_GET_MAX_ADSP_CLK_KHZ,
+ PCOM_CLK_REGIME_SEC_GET_I2C_CLK_KHZ,
+ PCOM_CLK_REGIME_SEC_MSM_GET_CLK_FREQ_KHZ,
+ PCOM_CLK_REGIME_SEC_SEL_VFE_SRC,
+ PCOM_CLK_REGIME_SEC_MSM_SEL_CAMCLK,
+ PCOM_CLK_REGIME_SEC_MSM_SEL_LCDCLK,
+ PCOM_CLK_REGIME_SEC_VFE_RAIL_OFF,
+ PCOM_CLK_REGIME_SEC_VFE_RAIL_ON,
+ PCOM_CLK_REGIME_SEC_GRP_RAIL_OFF,
+ PCOM_CLK_REGIME_SEC_GRP_RAIL_ON,
+ PCOM_CLK_REGIME_SEC_VDC_RAIL_OFF,
+ PCOM_CLK_REGIME_SEC_VDC_RAIL_ON,
+ PCOM_CLK_REGIME_SEC_LCD_CTRL,
+ PCOM_CLK_REGIME_SEC_REGISTER_FOR_CPU_RESOURCE,
+ PCOM_CLK_REGIME_SEC_DEREGISTER_FOR_CPU_RESOURCE,
+ PCOM_CLK_REGIME_SEC_RESOURCE_REQUEST_WRP,
+ PCOM_CLK_REGIME_MSM_SEC_SEL_CLK_OWNER,
+ PCOM_CLK_REGIME_SEC_DEVMAN_REQUEST_WRP,
+ PCOM_GPIO_CONFIG,
+ PCOM_GPIO_CONFIGURE_GROUP,
+ PCOM_GPIO_TLMM_SET_PORT,
+ PCOM_GPIO_TLMM_CONFIG_EX,
+ PCOM_SET_FTM_BOOT_COUNT,
+ PCOM_RESERVED0,
+ PCOM_RESERVED1,
+ PCOM_CUSTOMER_CMD1,
+ PCOM_CUSTOMER_CMD2,
+ PCOM_CUSTOMER_CMD3,
+ PCOM_CLK_REGIME_ENTER_APPSBL_CHG_MODE,
+ PCOM_CLK_REGIME_EXIT_APPSBL_CHG_MODE,
+ PCOM_CLK_REGIME_SEC_RAIL_DISABLE,
+ PCOM_CLK_REGIME_SEC_RAIL_ENABLE,
+ PCOM_CLK_REGIME_SEC_RAIL_CONTROL,
+ PCOM_SET_SW_WATCHDOG_STATE,
+ PCOM_PM_MPP_CONFIG_DIGITAL_INPUT,
+ PCOM_PM_MPP_CONFIG_I_SINK,
+ PCOM_RESERVED_101,
+ PCOM_MSM_HSUSB_PHY_RESET,
+ PCOM_GET_BATT_MV_LEVEL,
+ PCOM_CHG_USB_IS_PC_CONNECTED,
+ PCOM_CHG_USB_IS_CHARGER_CONNECTED,
+ PCOM_CHG_USB_IS_DISCONNECTED,
+ PCOM_CHG_USB_IS_AVAILABLE,
+ PCOM_CLK_REGIME_SEC_MSM_SEL_FREQ,
+ PCOM_CLK_REGIME_SEC_SET_PCLK_AXI_POLICY,
+ PCOM_CLKCTL_RPC_RESET_ASSERT,
+ PCOM_CLKCTL_RPC_RESET_DEASSERT,
+ PCOM_CLKCTL_RPC_RAIL_ON,
+ PCOM_CLKCTL_RPC_RAIL_OFF,
+ PCOM_CLKCTL_RPC_RAIL_ENABLE,
+ PCOM_CLKCTL_RPC_RAIL_DISABLE,
+ PCOM_CLKCTL_RPC_RAIL_CONTROL,
+ PCOM_CLKCTL_RPC_MIN_MSMC1,
PCOM_NUM_CMDS,
};
enum {
- PCOM_INVALID_STATUS = 0x0,
- PCOM_READY,
- PCOM_CMD_RUNNING,
- PCOM_CMD_SUCCESS,
- PCOM_CMD_FAIL,
+ PCOM_INVALID_STATUS = 0x0,
+ PCOM_READY,
+ PCOM_CMD_RUNNING,
+ PCOM_CMD_SUCCESS,
+ PCOM_CMD_FAIL,
+ PCOM_CMD_FAIL_FALSE_RETURNED,
+ PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_SERVER,
+ PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_CLIENT,
+ PCOM_CMD_FAIL_CMD_UNREGISTERED,
+ PCOM_CMD_FAIL_CMD_LOCKED,
+ PCOM_CMD_FAIL_SERVER_NOT_YET_READY,
+ PCOM_CMD_FAIL_BAD_DESTINATION,
+ PCOM_CMD_FAIL_SERVER_RESET,
+ PCOM_CMD_FAIL_SMSM_NOT_INIT,
+ PCOM_CMD_FAIL_PROC_COMM_BUSY,
+ PCOM_CMD_FAIL_PROC_COMM_NOT_INIT,
+
};
/* List of VREGs that support the Pull Down Resistor setting. */
-enum {
+enum vreg_pdown_id {
PM_VREG_PDOWN_MSMA_ID,
PM_VREG_PDOWN_MSMP_ID,
PM_VREG_PDOWN_MSME1_ID, /* Not supported in Panoramix */
@@ -131,6 +216,11 @@
PM_VREG_PDOWN_XO_ID = PM_VREG_PDOWN_TCXO_ID
};
+enum {
+ PCOM_CLKRGM_APPS_RESET_USB_PHY = 34,
+ PCOM_CLKRGM_APPS_RESET_USBH = 37,
+};
+
/* gpio info for PCOM_RPC_GPIO_TLMM_CONFIG_EX */
#define GPIO_ENABLE 0