memory-hotplug: add zone_for_memory() for selecting zone for new memory
This series of patches fixes a problem when adding memory in bad manner.
For example: for a x86_64 machine booted with "mem=400M" and with 2GiB
memory installed, following commands cause problem:
# echo 0x40000000 > /sys/devices/system/memory/probe
[ 28.613895] init_memory_mapping: [mem 0x40000000-0x47ffffff]
# echo 0x48000000 > /sys/devices/system/memory/probe
[ 28.693675] init_memory_mapping: [mem 0x48000000-0x4fffffff]
# echo online_movable > /sys/devices/system/memory/memory9/state
# echo 0x50000000 > /sys/devices/system/memory/probe
[ 29.084090] init_memory_mapping: [mem 0x50000000-0x57ffffff]
# echo 0x58000000 > /sys/devices/system/memory/probe
[ 29.151880] init_memory_mapping: [mem 0x58000000-0x5fffffff]
# echo online_movable > /sys/devices/system/memory/memory11/state
# echo online> /sys/devices/system/memory/memory8/state
# echo online> /sys/devices/system/memory/memory10/state
# echo offline> /sys/devices/system/memory/memory9/state
[ 30.558819] Offlined Pages 32768
# free
total used free shared buffers cached
Mem: 780588 18014398509432020 830552 0 0 51180
-/+ buffers/cache: 18014398509380840 881732
Swap: 0 0 0
This is because the above commands probe higher memory after online a
section with online_movable, which causes ZONE_HIGHMEM (or ZONE_NORMAL
for systems without ZONE_HIGHMEM) overlaps ZONE_MOVABLE.
After the second online_movable, the problem can be observed from
zoneinfo:
# cat /proc/zoneinfo
...
Node 0, zone Movable
pages free 65491
min 250
low 312
high 375
scanned 0
spanned 18446744073709518848
present 65536
managed 65536
...
This series of patches solve the problem by checking ZONE_MOVABLE when
choosing zone for new memory. If new memory is inside or higher than
ZONE_MOVABLE, makes it go there instead.
After applying this series of patches, following are free and zoneinfo
result (after offlining memory9):
bash-4.2# free
total used free shared buffers cached
Mem: 780956 80112 700844 0 0 51180
-/+ buffers/cache: 28932 752024
Swap: 0 0 0
bash-4.2# cat /proc/zoneinfo
Node 0, zone DMA
pages free 3389
min 14
low 17
high 21
scanned 0
spanned 4095
present 3998
managed 3977
nr_free_pages 3389
...
start_pfn: 1
inactive_ratio: 1
Node 0, zone DMA32
pages free 73724
min 341
low 426
high 511
scanned 0
spanned 98304
present 98304
managed 92958
nr_free_pages 73724
...
start_pfn: 4096
inactive_ratio: 1
Node 0, zone Normal
pages free 32630
min 120
low 150
high 180
scanned 0
spanned 32768
present 32768
managed 32768
nr_free_pages 32630
...
start_pfn: 262144
inactive_ratio: 1
Node 0, zone Movable
pages free 65476
min 241
low 301
high 361
scanned 0
spanned 98304
present 65536
managed 65536
nr_free_pages 65476
...
start_pfn: 294912
inactive_ratio: 1
This patch (of 7):
Introduce zone_for_memory() in arch independent code for
arch_add_memory() use.
Many arch_add_memory() function simply selects ZONE_HIGHMEM or
ZONE_NORMAL and add new memory into it. However, with the existance of
ZONE_MOVABLE, the selection method should be carefully considered: if
new, higher memory is added after ZONE_MOVABLE is setup, the default
zone and ZONE_MOVABLE may overlap each other.
should_add_memory_movable() checks the status of ZONE_MOVABLE. If it
has already contain memory, compare the address of new memory and
movable memory. If new memory is higher than movable, it should be
added into ZONE_MOVABLE instead of default zone.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Mel Gorman" <mgorman@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2 files changed