ARM: at91/boards: use -EINVAL for invalid gpio
this will allow to use gpio_is_valid
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index e209a299..d0b377b 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -44,10 +44,10 @@
/* USB Device */
struct at91_udc_data {
- u8 vbus_pin; /* high == host powering us */
+ int vbus_pin; /* high == host powering us */
u8 vbus_active_low; /* vbus polarity */
u8 vbus_polled; /* Use polling, not interrupt */
- u8 pullup_pin; /* active == D+ pulled up */
+ int pullup_pin; /* active == D+ pulled up */
u8 pullup_active_low; /* true == pullup_pin is active low */
};
extern void __init at91_add_device_udc(struct at91_udc_data *data);
@@ -57,10 +57,10 @@
/* Compact Flash */
struct at91_cf_data {
- u8 irq_pin; /* I/O IRQ */
- u8 det_pin; /* Card detect */
- u8 vcc_pin; /* power switching */
- u8 rst_pin; /* card reset */
+ int irq_pin; /* I/O IRQ */
+ int det_pin; /* Card detect */
+ int vcc_pin; /* power switching */
+ int rst_pin; /* card reset */
u8 chipselect; /* EBI Chip Select number */
u8 flags;
#define AT91_CF_TRUE_IDE 0x01
@@ -71,11 +71,11 @@
/* MMC / SD */
/* at91_mci platform config */
struct at91_mmc_data {
- u8 det_pin; /* card detect IRQ */
+ int det_pin; /* card detect IRQ */
unsigned slot_b:1; /* uses Slot B */
unsigned wire4:1; /* (SD) supports DAT0..DAT3 */
- u8 wp_pin; /* (SD) writeprotect detect */
- u8 vcc_pin; /* power switching (high == on) */
+ int wp_pin; /* (SD) writeprotect detect */
+ int vcc_pin; /* power switching (high == on) */
};
extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
@@ -87,10 +87,10 @@
/* USB Host */
struct at91_usbh_data {
u8 ports; /* number of ports on root hub */
- u8 vbus_pin[2]; /* port power-control pin */
+ int vbus_pin[2]; /* port power-control pin */
u8 vbus_pin_inverted;
u8 overcurrent_supported;
- u8 overcurrent_pin[2];
+ int overcurrent_pin[2];
u8 overcurrent_status[2];
u8 overcurrent_changed[2];
};
@@ -100,9 +100,9 @@
/* NAND / SmartMedia */
struct atmel_nand_data {
- u8 enable_pin; /* chip enable */
- u8 det_pin; /* card detect */
- u8 rdy_pin; /* ready/busy */
+ int enable_pin; /* chip enable */
+ int det_pin; /* card detect */
+ int rdy_pin; /* ready/busy */
u8 rdy_pin_active_low; /* rdy_pin value is inverted */
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */