igb: No longer rely on APME to determine WoL settings
Historically, we've been using the APME bit to determine whether a device
supports wake on a given port or not. However, this bit specifies the
default wake setting, rather than the wake support. Change the behavior so
that we use a flag to keep the capabilities separate from the enablement
while meeting customer requirements.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 0acf590..e2288b5 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -1966,54 +1966,6 @@
msleep_interruptible(4 * 1000);
}
-static int igb_wol_exclusion(struct igb_adapter *adapter,
- struct ethtool_wolinfo *wol)
-{
- struct e1000_hw *hw = &adapter->hw;
- int retval = 1; /* fail by default */
-
- switch (hw->device_id) {
- case E1000_DEV_ID_82575GB_QUAD_COPPER:
- /* WoL not supported */
- wol->supported = 0;
- break;
- case E1000_DEV_ID_82575EB_FIBER_SERDES:
- case E1000_DEV_ID_82576_FIBER:
- case E1000_DEV_ID_82576_SERDES:
- /* Wake events not supported on port B */
- if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1) {
- wol->supported = 0;
- break;
- }
- /* return success for non excluded adapter ports */
- retval = 0;
- break;
- case E1000_DEV_ID_82576_QUAD_COPPER:
- case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
- /* quad port adapters only support WoL on port A */
- if (!(adapter->flags & IGB_FLAG_QUAD_PORT_A)) {
- wol->supported = 0;
- break;
- }
- /* return success for non excluded adapter ports */
- retval = 0;
- break;
- default:
- /* dual port cards only support WoL on port A from now on
- * unless it was enabled in the eeprom for port B
- * so exclude FUNC_1 ports from having WoL enabled */
- if ((rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) &&
- !adapter->eeprom_wol) {
- wol->supported = 0;
- break;
- }
-
- retval = 0;
- }
-
- return retval;
-}
-
static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
{
struct igb_adapter *adapter = netdev_priv(netdev);
@@ -2023,10 +1975,7 @@
WAKE_PHY;
wol->wolopts = 0;
- /* this function will set ->supported = 0 and return 1 if wol is not
- * supported by this hardware */
- if (igb_wol_exclusion(adapter, wol) ||
- !device_can_wakeup(&adapter->pdev->dev))
+ if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED))
return;
/* apply any specific unsupported masks here */
@@ -2054,8 +2003,7 @@
if (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE))
return -EOPNOTSUPP;
- if (igb_wol_exclusion(adapter, wol) ||
- !device_can_wakeup(&adapter->pdev->dev))
+ if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED))
return wol->wolopts ? -EOPNOTSUPP : 0;
/* these settings will always override what we currently have */