drm/i915: Avoid mixing up SST and MST in DDI setup
The MST vs. SST selection should depend purely on the choice of the
connector/encoder. So don't try to determine the correct DDI mode
based on the intel_dp->is_mst, which simply tells us whether the sink
is in MST mode or not. Instead derive the information from the encoder
type. Since the link training code deals in non-fake encoders, we'll
also need to keep a second copy of that information around, which we'll
now designate as 'link_mst'.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index fc2ef2d..0400825 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -1126,7 +1126,6 @@
{
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct intel_encoder *intel_encoder = intel_ddi_get_crtc_encoder(crtc);
- struct drm_encoder *encoder = &intel_encoder->base;
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = to_i915(dev);
enum pipe pipe = intel_crtc->pipe;
@@ -1192,29 +1191,15 @@
temp |= TRANS_DDI_MODE_SELECT_HDMI;
else
temp |= TRANS_DDI_MODE_SELECT_DVI;
-
} else if (type == INTEL_OUTPUT_ANALOG) {
temp |= TRANS_DDI_MODE_SELECT_FDI;
temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
-
} else if (type == INTEL_OUTPUT_DP ||
type == INTEL_OUTPUT_EDP) {
- struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
-
- if (intel_dp->is_mst) {
- temp |= TRANS_DDI_MODE_SELECT_DP_MST;
- } else
- temp |= TRANS_DDI_MODE_SELECT_DP_SST;
-
+ temp |= TRANS_DDI_MODE_SELECT_DP_SST;
temp |= DDI_PORT_WIDTH(intel_crtc->config->lane_count);
} else if (type == INTEL_OUTPUT_DP_MST) {
- struct intel_dp *intel_dp = &enc_to_mst(encoder)->primary->dp;
-
- if (intel_dp->is_mst) {
- temp |= TRANS_DDI_MODE_SELECT_DP_MST;
- } else
- temp |= TRANS_DDI_MODE_SELECT_DP_SST;
-
+ temp |= TRANS_DDI_MODE_SELECT_DP_MST;
temp |= DDI_PORT_WIDTH(intel_crtc->config->lane_count);
} else {
WARN(1, "Invalid encoder type %d for pipe %c\n",
@@ -2139,7 +2124,7 @@
val = DP_TP_CTL_ENABLE |
DP_TP_CTL_LINK_TRAIN_PAT1 | DP_TP_CTL_SCRAMBLE_DISABLE;
- if (intel_dp->is_mst)
+ if (intel_dp->link_mst)
val |= DP_TP_CTL_MODE_MST;
else {
val |= DP_TP_CTL_MODE_SST;