ath5k: fix typos, bad comment formatting and GHz in place of MHz
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index 7e28676..e00ab5a 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -363,7 +363,7 @@
return 0;
}
-/* Schedule a gain probe check on the next transmited packet.
+/* Schedule a gain probe check on the next transmitted packet.
* That means our next packet is going to be sent with lower
* tx power and a Peak to Average Power Detector (PAPD) will try
* to measure the gain.
@@ -620,7 +620,7 @@
/* Check if measurement is ok and if we need
* to adjust gain, schedule a gain adjustment,
- * else switch back to the acive state */
+ * else switch back to the active state */
if (ath5k_hw_rf_check_gainf_readback(ah) &&
AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) &&
ath5k_hw_rf_gainf_adjust(ah)) {
@@ -807,7 +807,7 @@
* use b_OB and b_DB parameters stored
* in eeprom on ee->ee_ob[ee_mode][0]
*
- * For all other chips we use OB/DB for 2Ghz
+ * For all other chips we use OB/DB for 2GHz
* stored in the b/g modal section just like
* 802.11a on ee->ee_ob[ee_mode][1] */
if ((ah->ah_radio == AR5K_RF5111) ||
@@ -1259,7 +1259,7 @@
{
int ret;
/*
- * Check bounds supported by the PHY (we don't care about regultory
+ * Check bounds supported by the PHY (we don't care about regulatory
* restrictions at this point). Note: hw_value already has the band
* (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok()
* of the band by that */
@@ -1815,7 +1815,7 @@
} else if (ath5k_hw_reg_read(ah, AR5K_PHY_IQ) &
AR5K_PHY_IQ_SPUR_FILT_EN) {
- /* Clean up spur mitigation settings and disable fliter */
+ /* Clean up spur mitigation settings and disable filter */
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL,
AR5K_PHY_BIN_MASK_CTL_RATE, 0);
AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_IQ,
@@ -2510,8 +2510,8 @@
s16 max_pwr_idx;
s16 min_pwr_idx;
s16 mid_pwr_idx = 0;
- /* Edge flag turs on the 7nth bit on the PCDAC
- * to delcare the higher power curve (force values
+ /* Edge flag turns on the 7nth bit on the PCDAC
+ * to declare the higher power curve (force values
* to be greater than 64). If we only have one curve
* we don't need to set this, if we have 2 curves and
* fill the table backwards this can also be used to
@@ -2568,7 +2568,7 @@
}
/* Don't go below 1, extrapolate below if we have
- * already swithced to the lower power curve -or
+ * already switched to the lower power curve -or
* we only have one curve and edge_flag is zero
* anyway */
if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) {
@@ -2805,7 +2805,7 @@
/*
* This is the main function that uses all of the above
* to set PCDAC/PDADC table on hw for the current channel.
- * This table is used for tx power calibration on the basband,
+ * This table is used for tx power calibration on the baseband,
* without it we get weird tx power levels and in some cases
* distorted spectral mask
*/