mmc: fix comment typos
Correct spelling typo in drivers/mmc
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index d4619e2..2273ce6 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -641,7 +641,7 @@
/*
* If the host and card support UHS-I mode request the card
* to switch to 1.8V signaling level. No 1.8v signalling if
- * UHS mode is not enabled to maintain compatibilty and some
+ * UHS mode is not enabled to maintain compatibility and some
* systems that claim 1.8v signalling in fact do not support
* it.
*/
diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c
index efdb81d..74bed0f 100644
--- a/drivers/mmc/host/at91_mci.c
+++ b/drivers/mmc/host/at91_mci.c
@@ -356,7 +356,7 @@
}
/*
- * Update bytes tranfered count during a write operation
+ * Update bytes transfered count during a write operation
*/
static void at91_mci_update_bytes_xfered(struct at91mci_host *host)
{
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 322412c..eea9cf2 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -1021,7 +1021,7 @@
}
/*
- * Stop data transfer because error(s) occured.
+ * Stop data transfer because error(s) occurred.
*/
static void atmci_stop_transfer_pdc(struct atmel_mci *host)
{
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index bc28627..9684538 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -445,7 +445,7 @@
OMAP_HSMMC_WRITE(host->base, SYSCTL,
OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
- dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stoped\n");
+ dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n");
}
static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host,
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index e23f813..32f4a07 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -315,7 +315,7 @@
new_val = val & (SDHCI_CTRL_LED | \
SDHCI_CTRL_4BITBUS | \
SDHCI_CTRL_D3CD);
- /* ensure the endianess */
+ /* ensure the endianness */
new_val |= ESDHC_HOST_CONTROL_LE;
/* bits 8&9 are reserved on mx25 */
if (!is_imx25_esdhc(imx_data)) {
diff --git a/drivers/mmc/host/vub300.c b/drivers/mmc/host/vub300.c
index 3135a1a..58eab9a 100644
--- a/drivers/mmc/host/vub300.c
+++ b/drivers/mmc/host/vub300.c
@@ -806,7 +806,7 @@
* we suspect a buggy USB host controller
*/
} else if (!vub300->data) {
- /* this means that the command (typically CMD52) suceeded */
+ /* this means that the command (typically CMD52) succeeded */
} else if (vub300->resp.common.header_type != 0x02) {
/*
* this is an error response from the VUB300 chip