stmmac: remove dead code for STMMAC_TIMER support
The TIMER option is not longer supported and this
code can be considered dead for this driver in
the new kernel series.
In fact, It was not updated at all and never used.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index c6cdbc4..777234c 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -115,16 +115,6 @@
module_param(tc, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(tc, "DMA threshold control value");
-/* Pay attention to tune this parameter; take care of both
- * hardware capability and network stabitily/performance impact.
- * Many tests showed that ~4ms latency seems to be good enough. */
-#ifdef CONFIG_STMMAC_TIMER
-#define DEFAULT_PERIODIC_RATE 256
-static int tmrate = DEFAULT_PERIODIC_RATE;
-module_param(tmrate, int, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(tmrate, "External timer freq. (default: 256Hz)");
-#endif
-
#define DMA_BUFFER_SIZE BUF_SIZE_2KiB
static int buf_sz = DMA_BUFFER_SIZE;
module_param(buf_sz, int, S_IRUGO | S_IWUSR);
@@ -536,12 +526,6 @@
else
bfsize = stmmac_set_bfsize(dev->mtu, priv->dma_buf_sz);
-#ifdef CONFIG_STMMAC_TIMER
- /* Disable interrupts on completion for the reception if timer is on */
- if (likely(priv->tm->enable))
- dis_ic = 1;
-#endif
-
DBG(probe, INFO, "stmmac: txsize %d, rxsize %d, bfsize %d\n",
txsize, rxsize, bfsize);
@@ -775,22 +759,12 @@
static inline void stmmac_enable_irq(struct stmmac_priv *priv)
{
-#ifdef CONFIG_STMMAC_TIMER
- if (likely(priv->tm->enable))
- priv->tm->timer_start(tmrate);
- else
-#endif
- priv->hw->dma->enable_dma_irq(priv->ioaddr);
+ priv->hw->dma->enable_dma_irq(priv->ioaddr);
}
static inline void stmmac_disable_irq(struct stmmac_priv *priv)
{
-#ifdef CONFIG_STMMAC_TIMER
- if (likely(priv->tm->enable))
- priv->tm->timer_stop();
- else
-#endif
- priv->hw->dma->disable_dma_irq(priv->ioaddr);
+ priv->hw->dma->disable_dma_irq(priv->ioaddr);
}
static int stmmac_has_work(struct stmmac_priv *priv)
@@ -818,25 +792,6 @@
}
}
-#ifdef CONFIG_STMMAC_TIMER
-void stmmac_schedule(struct net_device *dev)
-{
- struct stmmac_priv *priv = netdev_priv(dev);
-
- priv->xstats.sched_timer_n++;
-
- _stmmac_schedule(priv);
-}
-
-static void stmmac_no_timer_started(unsigned int x)
-{;
-};
-
-static void stmmac_no_timer_stopped(void)
-{;
-};
-#endif
-
/**
* stmmac_tx_err:
* @priv: pointer to the private device structure
@@ -1038,23 +993,6 @@
struct stmmac_priv *priv = netdev_priv(dev);
int ret;
-#ifdef CONFIG_STMMAC_TIMER
- priv->tm = kzalloc(sizeof(struct stmmac_timer *), GFP_KERNEL);
- if (unlikely(priv->tm == NULL))
- return -ENOMEM;
-
- priv->tm->freq = tmrate;
-
- /* Test if the external timer can be actually used.
- * In case of failure continue without timer. */
- if (unlikely((stmmac_open_ext_timer(dev, priv->tm)) < 0)) {
- pr_warning("stmmaceth: cannot attach the external timer.\n");
- priv->tm->freq = 0;
- priv->tm->timer_start = stmmac_no_timer_started;
- priv->tm->timer_stop = stmmac_no_timer_stopped;
- } else
- priv->tm->enable = 1;
-#endif
clk_prepare_enable(priv->stmmac_clk);
stmmac_check_ether_addr(priv);
@@ -1141,10 +1079,6 @@
priv->hw->dma->start_tx(priv->ioaddr);
priv->hw->dma->start_rx(priv->ioaddr);
-#ifdef CONFIG_STMMAC_TIMER
- priv->tm->timer_start(tmrate);
-#endif
-
/* Dump DMA/MAC registers */
if (netif_msg_hw(priv)) {
priv->hw->mac->dump_regs(priv->ioaddr);
@@ -1170,9 +1104,6 @@
free_irq(dev->irq, dev);
open_error:
-#ifdef CONFIG_STMMAC_TIMER
- kfree(priv->tm);
-#endif
if (priv->phydev)
phy_disconnect(priv->phydev);
@@ -1203,12 +1134,6 @@
netif_stop_queue(dev);
-#ifdef CONFIG_STMMAC_TIMER
- /* Stop and release the timer */
- stmmac_close_ext_timer();
- if (priv->tm != NULL)
- kfree(priv->tm);
-#endif
napi_disable(&priv->napi);
/* Free the IRQ lines */
@@ -1323,12 +1248,6 @@
/* Interrupt on completition only for the latest segment */
priv->hw->desc->close_tx_desc(desc);
-#ifdef CONFIG_STMMAC_TIMER
- /* Clean IC while using timer */
- if (likely(priv->tm->enable))
- priv->hw->desc->clear_tx_ic(desc);
-#endif
-
wmb();
/* To avoid raise condition */
@@ -1523,7 +1442,7 @@
* stmmac_tx_timeout
* @dev : Pointer to net device structure
* Description: this function is called when a packet transmission fails to
- * complete within a reasonable tmrate. The driver will mark the error in the
+ * complete within a reasonable time. The driver will mark the error in the
* netdev structure and arrange for the device to be reset to a sane state
* in order to transmit a new packet.
*/
@@ -2141,11 +2060,6 @@
netif_device_detach(ndev);
netif_stop_queue(ndev);
-#ifdef CONFIG_STMMAC_TIMER
- priv->tm->timer_stop();
- if (likely(priv->tm->enable))
- dis_ic = 1;
-#endif
napi_disable(&priv->napi);
/* Stop TX/RX DMA */
@@ -2196,10 +2110,6 @@
priv->hw->dma->start_tx(priv->ioaddr);
priv->hw->dma->start_rx(priv->ioaddr);
-#ifdef CONFIG_STMMAC_TIMER
- if (likely(priv->tm->enable))
- priv->tm->timer_start(tmrate);
-#endif
napi_enable(&priv->napi);
netif_start_queue(ndev);
@@ -2295,11 +2205,6 @@
} else if (!strncmp(opt, "eee_timer:", 6)) {
if (kstrtoint(opt + 10, 0, &eee_timer))
goto err;
-#ifdef CONFIG_STMMAC_TIMER
- } else if (!strncmp(opt, "tmrate:", 7)) {
- if (kstrtoint(opt + 7, 0, &tmrate))
- goto err;
-#endif
}
}
return 0;