PCI: separate pci_setup_bridge to small functions
This is a good cleanup in itself, and makes it easier to modify specific
resource types in later code.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
diff --git a/drivers/pci/setup-bus.c b/drivers/pci/setup-bus.c
index c48cd37..1bd41ac 100644
--- a/drivers/pci/setup-bus.c
+++ b/drivers/pci/setup-bus.c
@@ -134,18 +134,12 @@
config space writes, so it's quite possible that an I/O window of
the bridge will have some undesirable address (e.g. 0) after the
first write. Ditto 64-bit prefetchable MMIO. */
-static void pci_setup_bridge(struct pci_bus *bus)
+static void pci_setup_bridge_io(struct pci_bus *bus)
{
struct pci_dev *bridge = bus->self;
struct resource *res;
struct pci_bus_region region;
- u32 l, bu, lu, io_upper16;
-
- if (pci_is_enabled(bridge))
- return;
-
- dev_info(&bridge->dev, "PCI bridge to [bus %02x-%02x]\n",
- bus->secondary, bus->subordinate);
+ u32 l, io_upper16;
/* Set up the top and bottom of the PCI I/O segment for this bus. */
res = bus->resource[0];
@@ -158,8 +152,7 @@
/* Set up upper 16 bits of I/O base/limit. */
io_upper16 = (region.end & 0xffff0000) | (region.start >> 16);
dev_info(&bridge->dev, " bridge window %pR\n", res);
- }
- else {
+ } else {
/* Clear upper 16 bits of I/O base/limit. */
io_upper16 = 0;
l = 0x00f0;
@@ -171,21 +164,35 @@
pci_write_config_dword(bridge, PCI_IO_BASE, l);
/* Update upper 16 bits of I/O base/limit. */
pci_write_config_dword(bridge, PCI_IO_BASE_UPPER16, io_upper16);
+}
- /* Set up the top and bottom of the PCI Memory segment
- for this bus. */
+static void pci_setup_bridge_mmio(struct pci_bus *bus)
+{
+ struct pci_dev *bridge = bus->self;
+ struct resource *res;
+ struct pci_bus_region region;
+ u32 l;
+
+ /* Set up the top and bottom of the PCI Memory segment for this bus. */
res = bus->resource[1];
pcibios_resource_to_bus(bridge, ®ion, res);
if (res->flags & IORESOURCE_MEM) {
l = (region.start >> 16) & 0xfff0;
l |= region.end & 0xfff00000;
dev_info(&bridge->dev, " bridge window %pR\n", res);
- }
- else {
+ } else {
l = 0x0000fff0;
dev_info(&bridge->dev, " bridge window [mem disabled]\n");
}
pci_write_config_dword(bridge, PCI_MEMORY_BASE, l);
+}
+
+static void pci_setup_bridge_mmio_pref(struct pci_bus *bus)
+{
+ struct pci_dev *bridge = bus->self;
+ struct resource *res;
+ struct pci_bus_region region;
+ u32 l, bu, lu;
/* Clear out the upper 32 bits of PREF limit.
If PCI_PREF_BASE_UPPER32 was non-zero, this temporarily
@@ -204,8 +211,7 @@
lu = upper_32_bits(region.end);
}
dev_info(&bridge->dev, " bridge window %pR\n", res);
- }
- else {
+ } else {
l = 0x0000fff0;
dev_info(&bridge->dev, " bridge window [mem pref disabled]\n");
}
@@ -214,10 +220,38 @@
/* Set the upper 32 bits of PREF base & limit. */
pci_write_config_dword(bridge, PCI_PREF_BASE_UPPER32, bu);
pci_write_config_dword(bridge, PCI_PREF_LIMIT_UPPER32, lu);
+}
+
+static void __pci_setup_bridge(struct pci_bus *bus, unsigned long type)
+{
+ struct pci_dev *bridge = bus->self;
+
+ if (pci_is_enabled(bridge))
+ return;
+
+ dev_info(&bridge->dev, "PCI bridge to [bus %02x-%02x]\n",
+ bus->secondary, bus->subordinate);
+
+ if (type & IORESOURCE_IO)
+ pci_setup_bridge_io(bus);
+
+ if (type & IORESOURCE_MEM)
+ pci_setup_bridge_mmio(bus);
+
+ if (type & IORESOURCE_PREFETCH)
+ pci_setup_bridge_mmio_pref(bus);
pci_write_config_word(bridge, PCI_BRIDGE_CONTROL, bus->bridge_ctl);
}
+static void pci_setup_bridge(struct pci_bus *bus)
+{
+ unsigned long type = IORESOURCE_IO | IORESOURCE_MEM |
+ IORESOURCE_PREFETCH;
+
+ __pci_setup_bridge(bus, type);
+}
+
/* Check whether the bridge supports optional I/O and
prefetchable memory ranges. If not, the respective
base/limit registers must be read-only and read as 0. */