drm/i915: Fix gen2 and hsw+ scanline counter
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index d537587..6db85e2 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -10231,6 +10231,44 @@
pipe_config->adjusted_mode.crtc_clock, dotclock);
}
+static void update_scanline_offset(struct intel_crtc *crtc)
+{
+ struct drm_device *dev = crtc->base.dev;
+
+ /*
+ * The scanline counter increments at the leading edge of hsync.
+ *
+ * On most platforms it starts counting from vtotal-1 on the
+ * first active line. That means the scanline counter value is
+ * always one less than what we would expect. Ie. just after
+ * start of vblank, which also occurs at start of hsync (on the
+ * last active line), the scanline counter will read vblank_start-1.
+ *
+ * On gen2 the scanline counter starts counting from 1 instead
+ * of vtotal-1, so we have to subtract one (or rather add vtotal-1
+ * to keep the value positive), instead of adding one.
+ *
+ * On HSW+ the behaviour of the scanline counter depends on the output
+ * type. For DP ports it behaves like most other platforms, but on HDMI
+ * there's an extra 1 line difference. So we need to add two instead of
+ * one to the value.
+ */
+ if (IS_GEN2(dev)) {
+ const struct drm_display_mode *mode = &crtc->config.adjusted_mode;
+ int vtotal;
+
+ vtotal = mode->crtc_vtotal;
+ if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+ vtotal /= 2;
+
+ crtc->scanline_offset = vtotal - 1;
+ } else if (HAS_DDI(dev) &&
+ intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_HDMI)) {
+ crtc->scanline_offset = 2;
+ } else
+ crtc->scanline_offset = 1;
+}
+
static int __intel_set_mode(struct drm_crtc *crtc,
struct drm_display_mode *mode,
int x, int y, struct drm_framebuffer *fb)
@@ -10349,8 +10387,11 @@
}
/* Now enable the clocks, plane, pipe, and connectors that we set up. */
- for_each_intel_crtc_masked(dev, prepare_pipes, intel_crtc)
+ for_each_intel_crtc_masked(dev, prepare_pipes, intel_crtc) {
+ update_scanline_offset(intel_crtc);
+
dev_priv->display.crtc_enable(&intel_crtc->base);
+ }
/* FIXME: add subpixel order */
done:
@@ -11900,6 +11941,8 @@
*/
crtc->cpu_fifo_underrun_disabled = true;
crtc->pch_fifo_underrun_disabled = true;
+
+ update_scanline_offset(crtc);
}
}