IB/ipath: Support blinking LEDs with an led_override file
When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.
A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
diff --git a/drivers/infiniband/hw/ipath/ipath_driver.c b/drivers/infiniband/hw/ipath/ipath_driver.c
index e3a2232..0975932 100644
--- a/drivers/infiniband/hw/ipath/ipath_driver.c
+++ b/drivers/infiniband/hw/ipath/ipath_driver.c
@@ -1846,6 +1846,87 @@
ipath_write_kreg(dd, where, value);
}
+/*
+ * Following deal with the "obviously simple" task of overriding the state
+ * of the LEDS, which normally indicate link physical and logical status.
+ * The complications arise in dealing with different hardware mappings
+ * and the board-dependent routine being called from interrupts.
+ * and then there's the requirement to _flash_ them.
+ */
+#define LED_OVER_FREQ_SHIFT 8
+#define LED_OVER_FREQ_MASK (0xFF<<LED_OVER_FREQ_SHIFT)
+/* Below is "non-zero" to force override, but both actual LEDs are off */
+#define LED_OVER_BOTH_OFF (8)
+
+void ipath_run_led_override(unsigned long opaque)
+{
+ struct ipath_devdata *dd = (struct ipath_devdata *)opaque;
+ int timeoff;
+ int pidx;
+ u64 lstate, ltstate, val;
+
+ if (!(dd->ipath_flags & IPATH_INITTED))
+ return;
+
+ pidx = dd->ipath_led_override_phase++ & 1;
+ dd->ipath_led_override = dd->ipath_led_override_vals[pidx];
+ timeoff = dd->ipath_led_override_timeoff;
+
+ /*
+ * below potentially restores the LED values per current status,
+ * should also possibly setup the traffic-blink register,
+ * but leave that to per-chip functions.
+ */
+ val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcstatus);
+ ltstate = (val >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
+ INFINIPATH_IBCS_LINKTRAININGSTATE_MASK;
+ lstate = (val >> INFINIPATH_IBCS_LINKSTATE_SHIFT) &
+ INFINIPATH_IBCS_LINKSTATE_MASK;
+
+ dd->ipath_f_setextled(dd, lstate, ltstate);
+ mod_timer(&dd->ipath_led_override_timer, jiffies + timeoff);
+}
+
+void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val)
+{
+ int timeoff, freq;
+
+ if (!(dd->ipath_flags & IPATH_INITTED))
+ return;
+
+ /* First check if we are blinking. If not, use 1HZ polling */
+ timeoff = HZ;
+ freq = (val & LED_OVER_FREQ_MASK) >> LED_OVER_FREQ_SHIFT;
+
+ if (freq) {
+ /* For blink, set each phase from one nybble of val */
+ dd->ipath_led_override_vals[0] = val & 0xF;
+ dd->ipath_led_override_vals[1] = (val >> 4) & 0xF;
+ timeoff = (HZ << 4)/freq;
+ } else {
+ /* Non-blink set both phases the same. */
+ dd->ipath_led_override_vals[0] = val & 0xF;
+ dd->ipath_led_override_vals[1] = val & 0xF;
+ }
+ dd->ipath_led_override_timeoff = timeoff;
+
+ /*
+ * If the timer has not already been started, do so. Use a "quick"
+ * timeout so the function will be called soon, to look at our request.
+ */
+ if (atomic_inc_return(&dd->ipath_led_override_timer_active) == 1) {
+ /* Need to start timer */
+ init_timer(&dd->ipath_led_override_timer);
+ dd->ipath_led_override_timer.function =
+ ipath_run_led_override;
+ dd->ipath_led_override_timer.data = (unsigned long) dd;
+ dd->ipath_led_override_timer.expires = jiffies + 1;
+ add_timer(&dd->ipath_led_override_timer);
+ } else {
+ atomic_dec(&dd->ipath_led_override_timer_active);
+ }
+}
+
/**
* ipath_shutdown_device - shut down a device
* @dd: the infinipath device
@@ -1909,7 +1990,6 @@
* Turn the LEDs off explictly for the same reason.
*/
dd->ipath_f_quiet_serdes(dd);
- dd->ipath_f_setextled(dd, 0, 0);
if (dd->ipath_stats_timer_active) {
del_timer_sync(&dd->ipath_stats_timer);
@@ -2085,6 +2165,16 @@
goto bail;
}
+ if (atomic_read(&dd->ipath_led_override_timer_active)) {
+ /* Need to stop LED timer, _then_ shut off LEDs */
+ del_timer_sync(&dd->ipath_led_override_timer);
+ atomic_set(&dd->ipath_led_override_timer_active, 0);
+ }
+
+ /* Shut off LEDs after we are sure timer is not running */
+ dd->ipath_led_override = LED_OVER_BOTH_OFF;
+ dd->ipath_f_setextled(dd, 0, 0);
+
dev_info(&dd->pcidev->dev, "Reset on unit %u requested\n", unit);
if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT)) {