ARM: dts: omap3-igep0030-common: Introduce igep0030 common dtsi file.
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEP COM MODULE hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts
index cc2a374..8150f47 100644
--- a/arch/arm/boot/dts/omap3-igep0030.dts
+++ b/arch/arm/boot/dts/omap3-igep0030.dts
@@ -9,42 +9,12 @@
* published by the Free Software Foundation.
*/
-#include "omap3-igep.dtsi"
+#include "omap3-igep0030-common.dtsi"
/ {
model = "IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)";
compatible = "isee,omap3-igep0030", "ti,omap36xx", "ti,omap3";
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&leds_pins>;
- compatible = "gpio-leds";
-
- boot {
- label = "omap3:green:boot";
- gpios = <&twl_gpio 13 GPIO_ACTIVE_LOW>;
- default-state = "on";
- };
-
- user0 {
- label = "omap3:red:user0";
- gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */
- default-state = "off";
- };
-
- user1 {
- label = "omap3:green:user1";
- gpios = <&twl_gpio 19 GPIO_ACTIVE_LOW>; /* LEDB */
- default-state = "off";
- };
-
- user2 {
- label = "omap3:red:user1";
- gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
- };
-
/* Regulator to trigger the WIFI_PDN signal of the Wifi module */
lbee1usjyc_pdn: lbee1usjyc_pdn {
compatible = "regulator-fixed";
@@ -75,22 +45,16 @@
OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 - RST_N_B */
>;
};
-
- uart2_pins: pinmux_uart2_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */
- OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_dr.uart2_rts */
- OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clk.uart2_tx */
- OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */
- >;
- };
};
-&omap3_pmx_core2 {
- leds_pins: pinmux_leds_pins {
- pinctrl-single,pins = <
- OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
- >;
+&leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_core2_pins>;
+
+ boot {
+ label = "omap3:green:boot";
+ gpios = <&twl_gpio 13 GPIO_ACTIVE_LOW>; /* LEDSYNC */
+ default-state = "on";
};
};
@@ -104,7 +68,3 @@
non-removable;
};
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
-};