[SCSI] SAS: consolidate linkspeed definitions
At the moment we have two separate linkspeed enumerations covering
roughly the same values. This patch consolidates on a single one enum
sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the
aic94xx driver. Eventually I'll get around to removing the duplicated
fields in asd_sas_phy and sas_phy ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c
index b653a26..02e796e 100644
--- a/drivers/scsi/libsas/sas_expander.c
+++ b/drivers/scsi/libsas/sas_expander.c
@@ -191,20 +191,7 @@
phy->phy->maximum_linkrate_hw = SAS_LINK_RATE_3_0_GBPS;
phy->phy->minimum_linkrate = SAS_LINK_RATE_1_5_GBPS;
phy->phy->maximum_linkrate = SAS_LINK_RATE_3_0_GBPS;
- switch (phy->linkrate) {
- case PHY_LINKRATE_1_5:
- phy->phy->negotiated_linkrate = SAS_LINK_RATE_1_5_GBPS;
- break;
- case PHY_LINKRATE_3:
- phy->phy->negotiated_linkrate = SAS_LINK_RATE_3_0_GBPS;
- break;
- case PHY_LINKRATE_6:
- phy->phy->negotiated_linkrate = SAS_LINK_RATE_6_0_GBPS;
- break;
- default:
- phy->phy->negotiated_linkrate = SAS_LINK_RATE_UNKNOWN;
- break;
- }
+ phy->phy->negotiated_linkrate = phy->linkrate;
if (!rediscover)
sas_phy_add(phy->phy);
@@ -450,7 +437,7 @@
struct ex_phy *phy = &ex->ex_phy[phy_id];
sas_smp_phy_control(dev, phy_id, PHY_FUNC_DISABLE);
- phy->linkrate = PHY_DISABLED;
+ phy->linkrate = SAS_PHY_DISABLED;
}
static void sas_ex_disable_port(struct domain_device *dev, u8 *sas_addr)
@@ -743,7 +730,7 @@
int res = 0;
/* Phy state */
- if (ex_phy->linkrate == PHY_SPINUP_HOLD) {
+ if (ex_phy->linkrate == SAS_SATA_SPINUP_HOLD) {
if (!sas_smp_phy_control(dev, phy_id, PHY_FUNC_LINK_RESET))
res = sas_ex_phy_discover(dev, phy_id);
if (res)
@@ -773,7 +760,7 @@
sas_configure_routing(dev, ex_phy->attached_sas_addr);
}
return 0;
- } else if (ex_phy->linkrate == PHY_LINKRATE_UNKNOWN)
+ } else if (ex_phy->linkrate == SAS_LINK_RATE_UNKNOWN)
return 0;
if (ex_phy->attached_dev_type != SAS_END_DEV &&
@@ -922,9 +909,9 @@
continue;
switch (ex_phy->linkrate) {
- case PHY_DISABLED:
- case PHY_RESET_PROBLEM:
- case PHY_PORT_SELECTOR:
+ case SAS_PHY_DISABLED:
+ case SAS_PHY_RESET_PROBLEM:
+ case SAS_SATA_PORT_SELECTOR:
continue;
default:
res = sas_ex_discover_dev(dev, i);