ath9k: add TX99 support
TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.
Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.
In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:
http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates
Example usage:
iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up
iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4
echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c
index 6bcf62f..bea5caa 100644
--- a/drivers/net/wireless/ath/ath9k/xmit.c
+++ b/drivers/net/wireless/ath/ath9k/xmit.c
@@ -1240,12 +1240,13 @@
if (bf->bf_next)
info.link = bf->bf_next->bf_daddr;
else
- info.link = 0;
+ info.link = (sc->tx99_state) ? bf->bf_daddr : 0;
if (!bf_first) {
bf_first = bf;
- info.flags = ATH9K_TXDESC_INTREQ;
+ if (!sc->tx99_state)
+ info.flags = ATH9K_TXDESC_INTREQ;
if ((tx_info->flags & IEEE80211_TX_CTL_CLEAR_PS_FILT) ||
txq == sc->tx.uapsdq)
info.flags |= ATH9K_TXDESC_CLRDMASK;
@@ -1932,7 +1933,7 @@
txq->axq_qnum, ito64(bf->bf_daddr), bf->bf_desc);
}
- if (!edma) {
+ if (!edma || sc->tx99_state) {
TX_STAT_INC(txq->axq_qnum, txstart);
ath9k_hw_txstart(ah, txq->axq_qnum);
}
@@ -2360,6 +2361,8 @@
dma_unmap_single(sc->dev, bf->bf_buf_addr, skb->len, DMA_TO_DEVICE);
bf->bf_buf_addr = 0;
+ if (sc->tx99_state)
+ goto skip_tx_complete;
if (bf->bf_state.bfs_paprd) {
if (time_after(jiffies,
@@ -2372,6 +2375,7 @@
ath_debug_stat_tx(sc, bf, ts, txq, tx_flags);
ath_tx_complete(sc, skb, tx_flags, txq);
}
+skip_tx_complete:
/* At this point, skb (bf->bf_mpdu) is consumed...make sure we don't
* accidentally reference it later.
*/
@@ -2730,3 +2734,46 @@
ath_txq_unlock(sc, txq);
}
}
+
+int ath9k_tx99_send(struct ath_softc *sc, struct sk_buff *skb,
+ struct ath_tx_control *txctl)
+{
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
+ struct ath_frame_info *fi = get_frame_info(skb);
+ struct ath_common *common = ath9k_hw_common(sc->sc_ah);
+ struct ath_buf *bf;
+ int padpos, padsize;
+
+ padpos = ieee80211_hdrlen(hdr->frame_control);
+ padsize = padpos & 3;
+
+ if (padsize && skb->len > padpos) {
+ if (skb_headroom(skb) < padsize) {
+ ath_dbg(common, XMIT,
+ "tx99 padding failed\n");
+ return -EINVAL;
+ }
+
+ skb_push(skb, padsize);
+ memmove(skb->data, skb->data + padsize, padpos);
+ }
+
+ fi->keyix = ATH9K_TXKEYIX_INVALID;
+ fi->framelen = skb->len + FCS_LEN;
+ fi->keytype = ATH9K_KEY_TYPE_CLEAR;
+
+ bf = ath_tx_setup_buffer(sc, txctl->txq, NULL, skb);
+ if (!bf) {
+ ath_dbg(common, XMIT, "tx99 buffer setup failed\n");
+ return -EINVAL;
+ }
+
+ ath_set_rates(sc->tx99_vif, NULL, bf);
+
+ ath9k_hw_set_desc_link(sc->sc_ah, bf->bf_desc, bf->bf_daddr);
+ ath9k_hw_tx99_start(sc->sc_ah, txctl->txq->axq_qnum);
+
+ ath_tx_send_normal(sc, txctl->txq, NULL, skb);
+
+ return 0;
+}