drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver
This driver adds support for Xilinx 10/100/1000 AXI Ethernet.
It can be used, for instance, on Xilinx boards with a Microblaze
architecture like the ML605.
The patch is against the latest net-next tree and checkpatch clean.
Signed-off-by: Ariane Keller <ariane.keller@tik.ee.ethz.ch>
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/MAINTAINERS b/MAINTAINERS
index 93c68d5..087b65d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7469,6 +7469,12 @@
F: Documentation/filesystems/xfs.txt
F: fs/xfs/
+XILINX AXI ETHERNET DRIVER
+M: Ariane Keller <ariane.keller@tik.ee.ethz.ch>
+M: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
+S: Maintained
+F: drivers/net/ethernet/xilinx/xilinx_axienet*
+
XILINX SYSTEMACE DRIVER
M: Grant Likely <grant.likely@secretlab.ca>
W: http://www.secretlab.ca/
diff --git a/drivers/net/ethernet/xilinx/Kconfig b/drivers/net/ethernet/xilinx/Kconfig
index d5a8260..5778a4a 100644
--- a/drivers/net/ethernet/xilinx/Kconfig
+++ b/drivers/net/ethernet/xilinx/Kconfig
@@ -25,6 +25,14 @@
---help---
This driver supports the 10/100 Ethernet Lite from Xilinx.
+config XILINX_AXI_EMAC
+ tristate "Xilinx 10/100/1000 AXI Ethernet support"
+ depends on (PPC32 || MICROBLAZE)
+ select PHYLIB
+ ---help---
+ This driver supports the 10/100/1000 Ethernet from Xilinx for the
+ AXI bus interface used in Xilinx Virtex FPGAs.
+
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
depends on (PPC || MICROBLAZE)
diff --git a/drivers/net/ethernet/xilinx/Makefile b/drivers/net/ethernet/xilinx/Makefile
index 5feac73..214205e 100644
--- a/drivers/net/ethernet/xilinx/Makefile
+++ b/drivers/net/ethernet/xilinx/Makefile
@@ -5,3 +5,5 @@
ll_temac-objs := ll_temac_main.o ll_temac_mdio.o
obj-$(CONFIG_XILINX_LL_TEMAC) += ll_temac.o
obj-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
+xilinx_emac-objs := xilinx_axienet_main.o xilinx_axienet_mdio.o
+obj-$(CONFIG_XILINX_AXI_EMAC) += xilinx_emac.o
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet.h b/drivers/net/ethernet/xilinx/xilinx_axienet.h
new file mode 100644
index 0000000..cc83af0
--- /dev/null
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet.h
@@ -0,0 +1,508 @@
+/*
+ * Definitions for Xilinx Axi Ethernet device driver.
+ *
+ * Copyright (c) 2009 Secret Lab Technologies, Ltd.
+ * Copyright (c) 2010 Xilinx, Inc. All rights reserved.
+ * Copyright (c) 2012 Daniel Borkmann, <daniel.borkmann@tik.ee.ethz.ch>
+ * Copyright (c) 2012 Ariane Keller, <ariane.keller@tik.ee.ethz.ch>
+ */
+
+#ifndef XILINX_AXIENET_H
+#define XILINX_AXIENET_H
+
+#include <linux/netdevice.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+
+/* Packet size info */
+#define XAE_HDR_SIZE 14 /* Size of Ethernet header */
+#define XAE_HDR_VLAN_SIZE 18 /* Size of an Ethernet hdr + VLAN */
+#define XAE_TRL_SIZE 4 /* Size of Ethernet trailer (FCS) */
+#define XAE_MTU 1500 /* Max MTU of an Ethernet frame */
+#define XAE_JUMBO_MTU 9000 /* Max MTU of a jumbo Eth. frame */
+
+#define XAE_MAX_FRAME_SIZE (XAE_MTU + XAE_HDR_SIZE + XAE_TRL_SIZE)
+#define XAE_MAX_VLAN_FRAME_SIZE (XAE_MTU + XAE_HDR_VLAN_SIZE + XAE_TRL_SIZE)
+#define XAE_MAX_JUMBO_FRAME_SIZE (XAE_JUMBO_MTU + XAE_HDR_SIZE + XAE_TRL_SIZE)
+
+/* Configuration options */
+
+/* Accept all incoming packets. Default: disabled (cleared) */
+#define XAE_OPTION_PROMISC (1 << 0)
+
+/* Jumbo frame support for Tx & Rx. Default: disabled (cleared) */
+#define XAE_OPTION_JUMBO (1 << 1)
+
+/* VLAN Rx & Tx frame support. Default: disabled (cleared) */
+#define XAE_OPTION_VLAN (1 << 2)
+
+/* Enable recognition of flow control frames on Rx. Default: enabled (set) */
+#define XAE_OPTION_FLOW_CONTROL (1 << 4)
+
+/* Strip FCS and PAD from incoming frames. Note: PAD from VLAN frames is not
+ * stripped. Default: disabled (set) */
+#define XAE_OPTION_FCS_STRIP (1 << 5)
+
+/* Generate FCS field and add PAD automatically for outgoing frames.
+ * Default: enabled (set) */
+#define XAE_OPTION_FCS_INSERT (1 << 6)
+
+/* Enable Length/Type error checking for incoming frames. When this option is
+ * set, the MAC will filter frames that have a mismatched type/length field
+ * and if XAE_OPTION_REPORT_RXERR is set, the user is notified when these
+ * types of frames are encountered. When this option is cleared, the MAC will
+ * allow these types of frames to be received. Default: enabled (set) */
+#define XAE_OPTION_LENTYPE_ERR (1 << 7)
+
+/* Enable the transmitter. Default: enabled (set) */
+#define XAE_OPTION_TXEN (1 << 11)
+
+/* Enable the receiver. Default: enabled (set) */
+#define XAE_OPTION_RXEN (1 << 12)
+
+/* Default options set when device is initialized or reset */
+#define XAE_OPTION_DEFAULTS \
+ (XAE_OPTION_TXEN | \
+ XAE_OPTION_FLOW_CONTROL | \
+ XAE_OPTION_RXEN)
+
+/* Axi DMA Register definitions */
+
+#define XAXIDMA_TX_CR_OFFSET 0x00000000 /* Channel control */
+#define XAXIDMA_TX_SR_OFFSET 0x00000004 /* Status */
+#define XAXIDMA_TX_CDESC_OFFSET 0x00000008 /* Current descriptor pointer */
+#define XAXIDMA_TX_TDESC_OFFSET 0x00000010 /* Tail descriptor pointer */
+
+#define XAXIDMA_RX_CR_OFFSET 0x00000030 /* Channel control */
+#define XAXIDMA_RX_SR_OFFSET 0x00000034 /* Status */
+#define XAXIDMA_RX_CDESC_OFFSET 0x00000038 /* Current descriptor pointer */
+#define XAXIDMA_RX_TDESC_OFFSET 0x00000040 /* Tail descriptor pointer */
+
+#define XAXIDMA_CR_RUNSTOP_MASK 0x00000001 /* Start/stop DMA channel */
+#define XAXIDMA_CR_RESET_MASK 0x00000004 /* Reset DMA engine */
+
+#define XAXIDMA_BD_NDESC_OFFSET 0x00 /* Next descriptor pointer */
+#define XAXIDMA_BD_BUFA_OFFSET 0x08 /* Buffer address */
+#define XAXIDMA_BD_CTRL_LEN_OFFSET 0x18 /* Control/buffer length */
+#define XAXIDMA_BD_STS_OFFSET 0x1C /* Status */
+#define XAXIDMA_BD_USR0_OFFSET 0x20 /* User IP specific word0 */
+#define XAXIDMA_BD_USR1_OFFSET 0x24 /* User IP specific word1 */
+#define XAXIDMA_BD_USR2_OFFSET 0x28 /* User IP specific word2 */
+#define XAXIDMA_BD_USR3_OFFSET 0x2C /* User IP specific word3 */
+#define XAXIDMA_BD_USR4_OFFSET 0x30 /* User IP specific word4 */
+#define XAXIDMA_BD_ID_OFFSET 0x34 /* Sw ID */
+#define XAXIDMA_BD_HAS_STSCNTRL_OFFSET 0x38 /* Whether has stscntrl strm */
+#define XAXIDMA_BD_HAS_DRE_OFFSET 0x3C /* Whether has DRE */
+
+#define XAXIDMA_BD_HAS_DRE_SHIFT 8 /* Whether has DRE shift */
+#define XAXIDMA_BD_HAS_DRE_MASK 0xF00 /* Whether has DRE mask */
+#define XAXIDMA_BD_WORDLEN_MASK 0xFF /* Whether has DRE mask */
+
+#define XAXIDMA_BD_CTRL_LENGTH_MASK 0x007FFFFF /* Requested len */
+#define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */
+#define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */
+#define XAXIDMA_BD_CTRL_ALL_MASK 0x0C000000 /* All control bits */
+
+#define XAXIDMA_DELAY_MASK 0xFF000000 /* Delay timeout counter */
+#define XAXIDMA_COALESCE_MASK 0x00FF0000 /* Coalesce counter */
+
+#define XAXIDMA_DELAY_SHIFT 24
+#define XAXIDMA_COALESCE_SHIFT 16
+
+#define XAXIDMA_IRQ_IOC_MASK 0x00001000 /* Completion intr */
+#define XAXIDMA_IRQ_DELAY_MASK 0x00002000 /* Delay interrupt */
+#define XAXIDMA_IRQ_ERROR_MASK 0x00004000 /* Error interrupt */
+#define XAXIDMA_IRQ_ALL_MASK 0x00007000 /* All interrupts */
+
+/* Default TX/RX Threshold and waitbound values for SGDMA mode */
+#define XAXIDMA_DFT_TX_THRESHOLD 24
+#define XAXIDMA_DFT_TX_WAITBOUND 254
+#define XAXIDMA_DFT_RX_THRESHOLD 24
+#define XAXIDMA_DFT_RX_WAITBOUND 254
+
+#define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */
+#define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */
+#define XAXIDMA_BD_CTRL_ALL_MASK 0x0C000000 /* All control bits */
+
+#define XAXIDMA_BD_STS_ACTUAL_LEN_MASK 0x007FFFFF /* Actual len */
+#define XAXIDMA_BD_STS_COMPLETE_MASK 0x80000000 /* Completed */
+#define XAXIDMA_BD_STS_DEC_ERR_MASK 0x40000000 /* Decode error */
+#define XAXIDMA_BD_STS_SLV_ERR_MASK 0x20000000 /* Slave error */
+#define XAXIDMA_BD_STS_INT_ERR_MASK 0x10000000 /* Internal err */
+#define XAXIDMA_BD_STS_ALL_ERR_MASK 0x70000000 /* All errors */
+#define XAXIDMA_BD_STS_RXSOF_MASK 0x08000000 /* First rx pkt */
+#define XAXIDMA_BD_STS_RXEOF_MASK 0x04000000 /* Last rx pkt */
+#define XAXIDMA_BD_STS_ALL_MASK 0xFC000000 /* All status bits */
+
+#define XAXIDMA_BD_MINIMUM_ALIGNMENT 0x40
+
+/* Axi Ethernet registers definition */
+#define XAE_RAF_OFFSET 0x00000000 /* Reset and Address filter */
+#define XAE_TPF_OFFSET 0x00000004 /* Tx Pause Frame */
+#define XAE_IFGP_OFFSET 0x00000008 /* Tx Inter-frame gap adjustment*/
+#define XAE_IS_OFFSET 0x0000000C /* Interrupt status */
+#define XAE_IP_OFFSET 0x00000010 /* Interrupt pending */
+#define XAE_IE_OFFSET 0x00000014 /* Interrupt enable */
+#define XAE_TTAG_OFFSET 0x00000018 /* Tx VLAN TAG */
+#define XAE_RTAG_OFFSET 0x0000001C /* Rx VLAN TAG */
+#define XAE_UAWL_OFFSET 0x00000020 /* Unicast address word lower */
+#define XAE_UAWU_OFFSET 0x00000024 /* Unicast address word upper */
+#define XAE_TPID0_OFFSET 0x00000028 /* VLAN TPID0 register */
+#define XAE_TPID1_OFFSET 0x0000002C /* VLAN TPID1 register */
+#define XAE_PPST_OFFSET 0x00000030 /* PCS PMA Soft Temac Status Reg */
+#define XAE_RCW0_OFFSET 0x00000400 /* Rx Configuration Word 0 */
+#define XAE_RCW1_OFFSET 0x00000404 /* Rx Configuration Word 1 */
+#define XAE_TC_OFFSET 0x00000408 /* Tx Configuration */
+#define XAE_FCC_OFFSET 0x0000040C /* Flow Control Configuration */
+#define XAE_EMMC_OFFSET 0x00000410 /* EMAC mode configuration */
+#define XAE_PHYC_OFFSET 0x00000414 /* RGMII/SGMII configuration */
+#define XAE_MDIO_MC_OFFSET 0x00000500 /* MII Management Config */
+#define XAE_MDIO_MCR_OFFSET 0x00000504 /* MII Management Control */
+#define XAE_MDIO_MWD_OFFSET 0x00000508 /* MII Management Write Data */
+#define XAE_MDIO_MRD_OFFSET 0x0000050C /* MII Management Read Data */
+#define XAE_MDIO_MIS_OFFSET 0x00000600 /* MII Management Interrupt Status */
+#define XAE_MDIO_MIP_OFFSET 0x00000620 /* MII Mgmt Interrupt Pending
+ * register offset */
+#define XAE_MDIO_MIE_OFFSET 0x00000640 /* MII Management Interrupt Enable
+ * register offset */
+#define XAE_MDIO_MIC_OFFSET 0x00000660 /* MII Management Interrupt Clear
+ * register offset. */
+#define XAE_UAW0_OFFSET 0x00000700 /* Unicast address word 0 */
+#define XAE_UAW1_OFFSET 0x00000704 /* Unicast address word 1 */
+#define XAE_FMI_OFFSET 0x00000708 /* Filter Mask Index */
+#define XAE_AF0_OFFSET 0x00000710 /* Address Filter 0 */
+#define XAE_AF1_OFFSET 0x00000714 /* Address Filter 1 */
+
+#define XAE_TX_VLAN_DATA_OFFSET 0x00004000 /* TX VLAN data table address */
+#define XAE_RX_VLAN_DATA_OFFSET 0x00008000 /* RX VLAN data table address */
+#define XAE_MCAST_TABLE_OFFSET 0x00020000 /* Multicast table address */
+
+/* Bit Masks for Axi Ethernet RAF register */
+#define XAE_RAF_MCSTREJ_MASK 0x00000002 /* Reject receive multicast
+ * destination address */
+#define XAE_RAF_BCSTREJ_MASK 0x00000004 /* Reject receive broadcast
+ * destination address */
+#define XAE_RAF_TXVTAGMODE_MASK 0x00000018 /* Tx VLAN TAG mode */
+#define XAE_RAF_RXVTAGMODE_MASK 0x00000060 /* Rx VLAN TAG mode */
+#define XAE_RAF_TXVSTRPMODE_MASK 0x00000180 /* Tx VLAN STRIP mode */
+#define XAE_RAF_RXVSTRPMODE_MASK 0x00000600 /* Rx VLAN STRIP mode */
+#define XAE_RAF_NEWFNCENBL_MASK 0x00000800 /* New function mode */
+#define XAE_RAF_EMULTIFLTRENBL_MASK 0x00001000 /* Exteneded Multicast
+ * Filtering mode
+ */
+#define XAE_RAF_STATSRST_MASK 0x00002000 /* Stats. Counter Reset */
+#define XAE_RAF_RXBADFRMEN_MASK 0x00004000 /* Recv Bad Frame Enable */
+#define XAE_RAF_TXVTAGMODE_SHIFT 3 /* Tx Tag mode shift bits */
+#define XAE_RAF_RXVTAGMODE_SHIFT 5 /* Rx Tag mode shift bits */
+#define XAE_RAF_TXVSTRPMODE_SHIFT 7 /* Tx strip mode shift bits*/
+#define XAE_RAF_RXVSTRPMODE_SHIFT 9 /* Rx Strip mode shift bits*/
+
+/* Bit Masks for Axi Ethernet TPF and IFGP registers */
+#define XAE_TPF_TPFV_MASK 0x0000FFFF /* Tx pause frame value */
+#define XAE_IFGP0_IFGP_MASK 0x0000007F /* Transmit inter-frame
+ * gap adjustment value */
+
+/* Bit Masks for Axi Ethernet IS, IE and IP registers, Same masks apply
+ * for all 3 registers. */
+#define XAE_INT_HARDACSCMPLT_MASK 0x00000001 /* Hard register access
+ * complete */
+#define XAE_INT_AUTONEG_MASK 0x00000002 /* Auto negotiation
+ * complete */
+#define XAE_INT_RXCMPIT_MASK 0x00000004 /* Rx complete */
+#define XAE_INT_RXRJECT_MASK 0x00000008 /* Rx frame rejected */
+#define XAE_INT_RXFIFOOVR_MASK 0x00000010 /* Rx fifo overrun */
+#define XAE_INT_TXCMPIT_MASK 0x00000020 /* Tx complete */
+#define XAE_INT_RXDCMLOCK_MASK 0x00000040 /* Rx Dcm Lock */
+#define XAE_INT_MGTRDY_MASK 0x00000080 /* MGT clock Lock */
+#define XAE_INT_PHYRSTCMPLT_MASK 0x00000100 /* Phy Reset complete */
+#define XAE_INT_ALL_MASK 0x0000003F /* All the ints */
+
+#define XAE_INT_RECV_ERROR_MASK \
+ (XAE_INT_RXRJECT_MASK | XAE_INT_RXFIFOOVR_MASK) /* INT bits that
+ * indicate receive
+ * errors */
+
+/* Bit masks for Axi Ethernet VLAN TPID Word 0 register */
+#define XAE_TPID_0_MASK 0x0000FFFF /* TPID 0 */
+#define XAE_TPID_1_MASK 0xFFFF0000 /* TPID 1 */
+
+/* Bit masks for Axi Ethernet VLAN TPID Word 1 register */
+#define XAE_TPID_2_MASK 0x0000FFFF /* TPID 0 */
+#define XAE_TPID_3_MASK 0xFFFF0000 /* TPID 1 */
+
+/* Bit masks for Axi Ethernet RCW1 register */
+#define XAE_RCW1_RST_MASK 0x80000000 /* Reset */
+#define XAE_RCW1_JUM_MASK 0x40000000 /* Jumbo frame enable */
+#define XAE_RCW1_FCS_MASK 0x20000000 /* In-Band FCS enable
+ * (FCS not stripped) */
+#define XAE_RCW1_RX_MASK 0x10000000 /* Receiver enable */
+#define XAE_RCW1_VLAN_MASK 0x08000000 /* VLAN frame enable */
+#define XAE_RCW1_LT_DIS_MASK 0x02000000 /* Length/type field valid check
+ * disable */
+#define XAE_RCW1_CL_DIS_MASK 0x01000000 /* Control frame Length check
+ * disable */
+#define XAE_RCW1_PAUSEADDR_MASK 0x0000FFFF /* Pause frame source address
+ * bits [47:32]. Bits [31:0] are
+ * stored in register RCW0 */
+
+/* Bit masks for Axi Ethernet TC register */
+#define XAE_TC_RST_MASK 0x80000000 /* Reset */
+#define XAE_TC_JUM_MASK 0x40000000 /* Jumbo frame enable */
+#define XAE_TC_FCS_MASK 0x20000000 /* In-Band FCS enable
+ * (FCS not generated) */
+#define XAE_TC_TX_MASK 0x10000000 /* Transmitter enable */
+#define XAE_TC_VLAN_MASK 0x08000000 /* VLAN frame enable */
+#define XAE_TC_IFG_MASK 0x02000000 /* Inter-frame gap adjustment
+ * enable */
+
+/* Bit masks for Axi Ethernet FCC register */
+#define XAE_FCC_FCRX_MASK 0x20000000 /* Rx flow control enable */
+#define XAE_FCC_FCTX_MASK 0x40000000 /* Tx flow control enable */
+
+/* Bit masks for Axi Ethernet EMMC register */
+#define XAE_EMMC_LINKSPEED_MASK 0xC0000000 /* Link speed */
+#define XAE_EMMC_RGMII_MASK 0x20000000 /* RGMII mode enable */
+#define XAE_EMMC_SGMII_MASK 0x10000000 /* SGMII mode enable */
+#define XAE_EMMC_GPCS_MASK 0x08000000 /* 1000BaseX mode enable */
+#define XAE_EMMC_HOST_MASK 0x04000000 /* Host interface enable */
+#define XAE_EMMC_TX16BIT 0x02000000 /* 16 bit Tx client enable */
+#define XAE_EMMC_RX16BIT 0x01000000 /* 16 bit Rx client enable */
+#define XAE_EMMC_LINKSPD_10 0x00000000 /* Link Speed mask for 10 Mbit */
+#define XAE_EMMC_LINKSPD_100 0x40000000 /* Link Speed mask for 100 Mbit */
+#define XAE_EMMC_LINKSPD_1000 0x80000000 /* Link Speed mask for 1000 Mbit */
+
+/* Bit masks for Axi Ethernet PHYC register */
+#define XAE_PHYC_SGMIILINKSPEED_MASK 0xC0000000 /* SGMII link speed mask*/
+#define XAE_PHYC_RGMIILINKSPEED_MASK 0x0000000C /* RGMII link speed */
+#define XAE_PHYC_RGMIIHD_MASK 0x00000002 /* RGMII Half-duplex */
+#define XAE_PHYC_RGMIILINK_MASK 0x00000001 /* RGMII link status */
+#define XAE_PHYC_RGLINKSPD_10 0x00000000 /* RGMII link 10 Mbit */
+#define XAE_PHYC_RGLINKSPD_100 0x00000004 /* RGMII link 100 Mbit */
+#define XAE_PHYC_RGLINKSPD_1000 0x00000008 /* RGMII link 1000 Mbit */
+#define XAE_PHYC_SGLINKSPD_10 0x00000000 /* SGMII link 10 Mbit */
+#define XAE_PHYC_SGLINKSPD_100 0x40000000 /* SGMII link 100 Mbit */
+#define XAE_PHYC_SGLINKSPD_1000 0x80000000 /* SGMII link 1000 Mbit */
+
+/* Bit masks for Axi Ethernet MDIO interface MC register */
+#define XAE_MDIO_MC_MDIOEN_MASK 0x00000040 /* MII management enable */
+#define XAE_MDIO_MC_CLOCK_DIVIDE_MAX 0x3F /* Maximum MDIO divisor */
+
+/* Bit masks for Axi Ethernet MDIO interface MCR register */
+#define XAE_MDIO_MCR_PHYAD_MASK 0x1F000000 /* Phy Address Mask */
+#define XAE_MDIO_MCR_PHYAD_SHIFT 24 /* Phy Address Shift */
+#define XAE_MDIO_MCR_REGAD_MASK 0x001F0000 /* Reg Address Mask */
+#define XAE_MDIO_MCR_REGAD_SHIFT 16 /* Reg Address Shift */
+#define XAE_MDIO_MCR_OP_MASK 0x0000C000 /* Operation Code Mask */
+#define XAE_MDIO_MCR_OP_SHIFT 13 /* Operation Code Shift */
+#define XAE_MDIO_MCR_OP_READ_MASK 0x00008000 /* Op Code Read Mask */
+#define XAE_MDIO_MCR_OP_WRITE_MASK 0x00004000 /* Op Code Write Mask */
+#define XAE_MDIO_MCR_INITIATE_MASK 0x00000800 /* Ready Mask */
+#define XAE_MDIO_MCR_READY_MASK 0x00000080 /* Ready Mask */
+
+/* Bit masks for Axi Ethernet MDIO interface MIS, MIP, MIE, MIC registers */
+#define XAE_MDIO_INT_MIIM_RDY_MASK 0x00000001 /* MIIM Interrupt */
+
+/* Bit masks for Axi Ethernet UAW1 register */
+#define XAE_UAW1_UNICASTADDR_MASK 0x0000FFFF /* Station address bits
+ * [47:32]; Station address
+ * bits [31:0] are stored in
+ * register UAW0 */
+
+/* Bit masks for Axi Ethernet FMI register */
+#define XAE_FMI_PM_MASK 0x80000000 /* Promis. mode enable */
+#define XAE_FMI_IND_MASK 0x00000003 /* Index Mask */
+
+#define XAE_MDIO_DIV_DFT 29 /* Default MDIO clock divisor */
+
+/* Defines for different options for C_PHY_TYPE parameter in Axi Ethernet IP */
+#define XAE_PHY_TYPE_MII 0
+#define XAE_PHY_TYPE_GMII 1
+#define XAE_PHY_TYPE_RGMII_1_3 2
+#define XAE_PHY_TYPE_RGMII_2_0 3
+#define XAE_PHY_TYPE_SGMII 4
+#define XAE_PHY_TYPE_1000BASE_X 5
+
+#define XAE_MULTICAST_CAM_TABLE_NUM 4 /* Total number of entries in the
+ * hardware multicast table. */
+
+/* Axi Ethernet Synthesis features */
+#define XAE_FEATURE_PARTIAL_RX_CSUM (1 << 0)
+#define XAE_FEATURE_PARTIAL_TX_CSUM (1 << 1)
+#define XAE_FEATURE_FULL_RX_CSUM (1 << 2)
+#define XAE_FEATURE_FULL_TX_CSUM (1 << 3)
+
+#define XAE_NO_CSUM_OFFLOAD 0
+
+#define XAE_FULL_CSUM_STATUS_MASK 0x00000038
+#define XAE_IP_UDP_CSUM_VALIDATED 0x00000003
+#define XAE_IP_TCP_CSUM_VALIDATED 0x00000002
+
+#define DELAY_OF_ONE_MILLISEC 1000
+
+/**
+ * struct axidma_bd - Axi Dma buffer descriptor layout
+ * @next: MM2S/S2MM Next Descriptor Pointer
+ * @reserved1: Reserved and not used
+ * @phys: MM2S/S2MM Buffer Address
+ * @reserved2: Reserved and not used
+ * @reserved3: Reserved and not used
+ * @reserved4: Reserved and not used
+ * @cntrl: MM2S/S2MM Control value
+ * @status: MM2S/S2MM Status value
+ * @app0: MM2S/S2MM User Application Field 0.
+ * @app1: MM2S/S2MM User Application Field 1.
+ * @app2: MM2S/S2MM User Application Field 2.
+ * @app3: MM2S/S2MM User Application Field 3.
+ * @app4: MM2S/S2MM User Application Field 4.
+ * @sw_id_offset: MM2S/S2MM Sw ID
+ * @reserved5: Reserved and not used
+ * @reserved6: Reserved and not used
+ */
+struct axidma_bd {
+ u32 next; /* Physical address of next buffer descriptor */
+ u32 reserved1;
+ u32 phys;
+ u32 reserved2;
+ u32 reserved3;
+ u32 reserved4;
+ u32 cntrl;
+ u32 status;
+ u32 app0;
+ u32 app1; /* TX start << 16 | insert */
+ u32 app2; /* TX csum seed */
+ u32 app3;
+ u32 app4;
+ u32 sw_id_offset;
+ u32 reserved5;
+ u32 reserved6;
+};
+
+/**
+ * struct axienet_local - axienet private per device data
+ * @ndev: Pointer for net_device to which it will be attached.
+ * @dev: Pointer to device structure
+ * @phy_dev: Pointer to PHY device structure attached to the axienet_local
+ * @phy_node: Pointer to device node structure
+ * @mii_bus: Pointer to MII bus structure
+ * @mdio_irqs: IRQs table for MDIO bus required in mii_bus structure
+ * @regs: Base address for the axienet_local device address space
+ * @dma_regs: Base address for the axidma device address space
+ * @dma_err_tasklet: Tasklet structure to process Axi DMA errors
+ * @tx_irq: Axidma TX IRQ number
+ * @rx_irq: Axidma RX IRQ number
+ * @temac_type: axienet type to identify between soft and hard temac
+ * @phy_type: Phy type to identify between MII/GMII/RGMII/SGMII/1000 Base-X
+ * @options: AxiEthernet option word
+ * @last_link: Phy link state in which the PHY was negotiated earlier
+ * @features: Stores the extended features supported by the axienet hw
+ * @tx_bd_v: Virtual address of the TX buffer descriptor ring
+ * @tx_bd_p: Physical address(start address) of the TX buffer descr. ring
+ * @rx_bd_v: Virtual address of the RX buffer descriptor ring
+ * @rx_bd_p: Physical address(start address) of the RX buffer descr. ring
+ * @tx_bd_ci: Stores the index of the Tx buffer descriptor in the ring being
+ * accessed currently. Used while alloc. BDs before a TX starts
+ * @tx_bd_tail: Stores the index of the Tx buffer descriptor in the ring being
+ * accessed currently. Used while processing BDs after the TX
+ * completed.
+ * @rx_bd_ci: Stores the index of the Rx buffer descriptor in the ring being
+ * accessed currently.
+ * @max_frm_size: Stores the maximum size of the frame that can be that
+ * Txed/Rxed in the existing hardware. If jumbo option is
+ * supported, the maximum frame size would be 9k. Else it is
+ * 1522 bytes (assuming support for basic VLAN)
+ * @jumbo_support: Stores hardware configuration for jumbo support. If hardware
+ * can handle jumbo packets, this entry will be 1, else 0.
+ */
+struct axienet_local {
+ struct net_device *ndev;
+ struct device *dev;
+
+ /* Connection to PHY device */
+ struct phy_device *phy_dev; /* Pointer to PHY device */
+ struct device_node *phy_node;
+
+ /* MDIO bus data */
+ struct mii_bus *mii_bus; /* MII bus reference */
+ int mdio_irqs[PHY_MAX_ADDR]; /* IRQs table for MDIO bus */
+
+ /* IO registers, dma functions and IRQs */
+ void __iomem *regs;
+ void __iomem *dma_regs;
+
+ struct tasklet_struct dma_err_tasklet;
+
+ int tx_irq;
+ int rx_irq;
+ u32 temac_type;
+ u32 phy_type;
+
+ u32 options; /* Current options word */
+ u32 last_link;
+ u32 features;
+
+ /* Buffer descriptors */
+ struct axidma_bd *tx_bd_v;
+ dma_addr_t tx_bd_p;
+ struct axidma_bd *rx_bd_v;
+ dma_addr_t rx_bd_p;
+ u32 tx_bd_ci;
+ u32 tx_bd_tail;
+ u32 rx_bd_ci;
+
+ u32 max_frm_size;
+ u32 jumbo_support;
+
+ int csum_offload_on_tx_path;
+ int csum_offload_on_rx_path;
+
+ u32 coalesce_count_rx;
+ u32 coalesce_count_tx;
+};
+
+/**
+ * struct axiethernet_option - Used to set axi ethernet hardware options
+ * @opt: Option to be set.
+ * @reg: Register offset to be written for setting the option
+ * @m_or: Mask to be ORed for setting the option in the register
+ */
+struct axienet_option {
+ u32 opt;
+ u32 reg;
+ u32 m_or;
+};
+
+/**
+ * axienet_ior - Memory mapped Axi Ethernet register read
+ * @lp: Pointer to axienet local structure
+ * @offset: Address offset from the base address of Axi Ethernet core
+ *
+ * returns: The contents of the Axi Ethernet register
+ *
+ * This function returns the contents of the corresponding register.
+ */
+static inline u32 axienet_ior(struct axienet_local *lp, off_t offset)
+{
+ return in_be32(lp->regs + offset);
+}
+
+/**
+ * axienet_iow - Memory mapped Axi Ethernet register write
+ * @lp: Pointer to axienet local structure
+ * @offset: Address offset from the base address of Axi Ethernet core
+ * @value: Value to be written into the Axi Ethernet register
+ *
+ * This function writes the desired value into the corresponding Axi Ethernet
+ * register.
+ */
+static inline void axienet_iow(struct axienet_local *lp, off_t offset,
+ u32 value)
+{
+ out_be32((lp->regs + offset), value);
+}
+
+/* Function prototypes visible in xilinx_axienet_mdio.c for other files */
+int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np);
+int axienet_mdio_wait_until_ready(struct axienet_local *lp);
+void axienet_mdio_teardown(struct axienet_local *lp);
+
+#endif /* XILINX_AXI_ENET_H */
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
new file mode 100644
index 0000000..ea50caf
--- /dev/null
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -0,0 +1,1682 @@
+/*
+ * Xilinx Axi Ethernet device driver
+ *
+ * Copyright (c) 2008 Nissin Systems Co., Ltd., Yoshio Kashiwagi
+ * Copyright (c) 2005-2008 DLA Systems, David H. Lynch Jr. <dhlii@dlasys.net>
+ * Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
+ * Copyright (c) 2010 Xilinx, Inc. All rights reserved.
+ * Copyright (c) 2012 Daniel Borkmann, <daniel.borkmann@tik.ee.ethz.ch>
+ * Copyright (c) 2012 Ariane Keller, <ariane.keller@tik.ee.ethz.ch>
+ *
+ * This is a driver for the Xilinx Axi Ethernet which is used in the Virtex6
+ * and Spartan6.
+ *
+ * TODO:
+ * - Add Axi Fifo support.
+ * - Factor out Axi DMA code into separate driver.
+ * - Test and fix basic multicast filtering.
+ * - Add support for extended multicast filtering.
+ * - Test basic VLAN support.
+ * - Add support for extended VLAN support.
+ */
+
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_mdio.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/phy.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+
+#include "xilinx_axienet.h"
+
+/* Descriptors defines for Tx and Rx DMA - 2^n for the best performance */
+#define TX_BD_NUM 64
+#define RX_BD_NUM 128
+
+/* Must be shorter than length of ethtool_drvinfo.driver field to fit */
+#define DRIVER_NAME "xaxienet"
+#define DRIVER_DESCRIPTION "Xilinx Axi Ethernet driver"
+#define DRIVER_VERSION "1.00a"
+
+#define AXIENET_REGS_N 32
+
+/* Match table for of_platform binding */
+static struct of_device_id axienet_of_match[] __devinitdata = {
+ { .compatible = "xlnx,axi-ethernet-1.00.a", },
+ { .compatible = "xlnx,axi-ethernet-1.01.a", },
+ { .compatible = "xlnx,axi-ethernet-2.01.a", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, axienet_of_match);
+
+/* Option table for setting up Axi Ethernet hardware options */
+static struct axienet_option axienet_options[] = {
+ /* Turn on jumbo packet support for both Rx and Tx */
+ {
+ .opt = XAE_OPTION_JUMBO,
+ .reg = XAE_TC_OFFSET,
+ .m_or = XAE_TC_JUM_MASK,
+ }, {
+ .opt = XAE_OPTION_JUMBO,
+ .reg = XAE_RCW1_OFFSET,
+ .m_or = XAE_RCW1_JUM_MASK,
+ }, { /* Turn on VLAN packet support for both Rx and Tx */
+ .opt = XAE_OPTION_VLAN,
+ .reg = XAE_TC_OFFSET,
+ .m_or = XAE_TC_VLAN_MASK,
+ }, {
+ .opt = XAE_OPTION_VLAN,
+ .reg = XAE_RCW1_OFFSET,
+ .m_or = XAE_RCW1_VLAN_MASK,
+ }, { /* Turn on FCS stripping on receive packets */
+ .opt = XAE_OPTION_FCS_STRIP,
+ .reg = XAE_RCW1_OFFSET,
+ .m_or = XAE_RCW1_FCS_MASK,
+ }, { /* Turn on FCS insertion on transmit packets */
+ .opt = XAE_OPTION_FCS_INSERT,
+ .reg = XAE_TC_OFFSET,
+ .m_or = XAE_TC_FCS_MASK,
+ }, { /* Turn off length/type field checking on receive packets */
+ .opt = XAE_OPTION_LENTYPE_ERR,
+ .reg = XAE_RCW1_OFFSET,
+ .m_or = XAE_RCW1_LT_DIS_MASK,
+ }, { /* Turn on Rx flow control */
+ .opt = XAE_OPTION_FLOW_CONTROL,
+ .reg = XAE_FCC_OFFSET,
+ .m_or = XAE_FCC_FCRX_MASK,
+ }, { /* Turn on Tx flow control */
+ .opt = XAE_OPTION_FLOW_CONTROL,
+ .reg = XAE_FCC_OFFSET,
+ .m_or = XAE_FCC_FCTX_MASK,
+ }, { /* Turn on promiscuous frame filtering */
+ .opt = XAE_OPTION_PROMISC,
+ .reg = XAE_FMI_OFFSET,
+ .m_or = XAE_FMI_PM_MASK,
+ }, { /* Enable transmitter */
+ .opt = XAE_OPTION_TXEN,
+ .reg = XAE_TC_OFFSET,
+ .m_or = XAE_TC_TX_MASK,
+ }, { /* Enable receiver */
+ .opt = XAE_OPTION_RXEN,
+ .reg = XAE_RCW1_OFFSET,
+ .m_or = XAE_RCW1_RX_MASK,
+ },
+ {}
+};
+
+/**
+ * axienet_dma_in32 - Memory mapped Axi DMA register read
+ * @lp: Pointer to axienet local structure
+ * @reg: Address offset from the base address of the Axi DMA core
+ *
+ * returns: The contents of the Axi DMA register
+ *
+ * This function returns the contents of the corresponding Axi DMA register.
+ */
+static inline u32 axienet_dma_in32(struct axienet_local *lp, off_t reg)
+{
+ return in_be32(lp->dma_regs + reg);
+}
+
+/**
+ * axienet_dma_out32 - Memory mapped Axi DMA register write.
+ * @lp: Pointer to axienet local structure
+ * @reg: Address offset from the base address of the Axi DMA core
+ * @value: Value to be written into the Axi DMA register
+ *
+ * This function writes the desired value into the corresponding Axi DMA
+ * register.
+ */
+static inline void axienet_dma_out32(struct axienet_local *lp,
+ off_t reg, u32 value)
+{
+ out_be32((lp->dma_regs + reg), value);
+}
+
+/**
+ * axienet_dma_bd_release - Release buffer descriptor rings
+ * @ndev: Pointer to the net_device structure
+ *
+ * This function is used to release the descriptors allocated in
+ * axienet_dma_bd_init. axienet_dma_bd_release is called when Axi Ethernet
+ * driver stop api is called.
+ */
+static void axienet_dma_bd_release(struct net_device *ndev)
+{
+ int i;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ for (i = 0; i < RX_BD_NUM; i++) {
+ dma_unmap_single(ndev->dev.parent, lp->rx_bd_v[i].phys,
+ lp->max_frm_size, DMA_FROM_DEVICE);
+ dev_kfree_skb((struct sk_buff *)
+ (lp->rx_bd_v[i].sw_id_offset));
+ }
+
+ if (lp->rx_bd_v) {
+ dma_free_coherent(ndev->dev.parent,
+ sizeof(*lp->rx_bd_v) * RX_BD_NUM,
+ lp->rx_bd_v,
+ lp->rx_bd_p);
+ }
+ if (lp->tx_bd_v) {
+ dma_free_coherent(ndev->dev.parent,
+ sizeof(*lp->tx_bd_v) * TX_BD_NUM,
+ lp->tx_bd_v,
+ lp->tx_bd_p);
+ }
+}
+
+/**
+ * axienet_dma_bd_init - Setup buffer descriptor rings for Axi DMA
+ * @ndev: Pointer to the net_device structure
+ *
+ * returns: 0, on success
+ * -ENOMEM, on failure
+ *
+ * This function is called to initialize the Rx and Tx DMA descriptor
+ * rings. This initializes the descriptors with required default values
+ * and is called when Axi Ethernet driver reset is called.
+ */
+static int axienet_dma_bd_init(struct net_device *ndev)
+{
+ u32 cr;
+ int i;
+ struct sk_buff *skb;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ /* Reset the indexes which are used for accessing the BDs */
+ lp->tx_bd_ci = 0;
+ lp->tx_bd_tail = 0;
+ lp->rx_bd_ci = 0;
+
+ /*
+ * Allocate the Tx and Rx buffer descriptors.
+ */
+ lp->tx_bd_v = dma_alloc_coherent(ndev->dev.parent,
+ sizeof(*lp->tx_bd_v) * TX_BD_NUM,
+ &lp->tx_bd_p,
+ GFP_KERNEL);
+ if (!lp->tx_bd_v) {
+ dev_err(&ndev->dev, "unable to allocate DMA Tx buffer "
+ "descriptors");
+ goto out;
+ }
+
+ lp->rx_bd_v = dma_alloc_coherent(ndev->dev.parent,
+ sizeof(*lp->rx_bd_v) * RX_BD_NUM,
+ &lp->rx_bd_p,
+ GFP_KERNEL);
+ if (!lp->rx_bd_v) {
+ dev_err(&ndev->dev, "unable to allocate DMA Rx buffer "
+ "descriptors");
+ goto out;
+ }
+
+ memset(lp->tx_bd_v, 0, sizeof(*lp->tx_bd_v) * TX_BD_NUM);
+ for (i = 0; i < TX_BD_NUM; i++) {
+ lp->tx_bd_v[i].next = lp->tx_bd_p +
+ sizeof(*lp->tx_bd_v) *
+ ((i + 1) % TX_BD_NUM);
+ }
+
+ memset(lp->rx_bd_v, 0, sizeof(*lp->rx_bd_v) * RX_BD_NUM);
+ for (i = 0; i < RX_BD_NUM; i++) {
+ lp->rx_bd_v[i].next = lp->rx_bd_p +
+ sizeof(*lp->rx_bd_v) *
+ ((i + 1) % RX_BD_NUM);
+
+ skb = netdev_alloc_skb_ip_align(ndev, lp->max_frm_size);
+ if (!skb) {
+ dev_err(&ndev->dev, "alloc_skb error %d\n", i);
+ goto out;
+ }
+
+ lp->rx_bd_v[i].sw_id_offset = (u32) skb;
+ lp->rx_bd_v[i].phys = dma_map_single(ndev->dev.parent,
+ skb->data,
+ lp->max_frm_size,
+ DMA_FROM_DEVICE);
+ lp->rx_bd_v[i].cntrl = lp->max_frm_size;
+ }
+
+ /* Start updating the Rx channel control register */
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
+ ((lp->coalesce_count_rx) << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = ((cr & ~XAXIDMA_DELAY_MASK) |
+ (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Write to the Rx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
+
+ /* Start updating the Tx channel control register */
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
+ ((lp->coalesce_count_tx) << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
+ (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Write to the Tx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
+
+ /* Populate the tail pointer and bring the Rx Axi DMA engine out of
+ * halted state. This will make the Rx side ready for reception.*/
+ axienet_dma_out32(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+ axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
+ (sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
+
+ /* Write to the RS (Run-stop) bit in the Tx channel control register.
+ * Tx channel is now ready to run. But only after we write to the
+ * tail pointer register that the Tx channel will start transmitting */
+ axienet_dma_out32(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+
+ return 0;
+out:
+ axienet_dma_bd_release(ndev);
+ return -ENOMEM;
+}
+
+/**
+ * axienet_set_mac_address - Write the MAC address
+ * @ndev: Pointer to the net_device structure
+ * @address: 6 byte Address to be written as MAC address
+ *
+ * This function is called to initialize the MAC address of the Axi Ethernet
+ * core. It writes to the UAW0 and UAW1 registers of the core.
+ */
+static void axienet_set_mac_address(struct net_device *ndev, void *address)
+{
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ if (address)
+ memcpy(ndev->dev_addr, address, ETH_ALEN);
+ if (!is_valid_ether_addr(ndev->dev_addr))
+ random_ether_addr(ndev->dev_addr);
+
+ /* Set up unicast MAC address filter set its mac address */
+ axienet_iow(lp, XAE_UAW0_OFFSET,
+ (ndev->dev_addr[0]) |
+ (ndev->dev_addr[1] << 8) |
+ (ndev->dev_addr[2] << 16) |
+ (ndev->dev_addr[3] << 24));
+ axienet_iow(lp, XAE_UAW1_OFFSET,
+ (((axienet_ior(lp, XAE_UAW1_OFFSET)) &
+ ~XAE_UAW1_UNICASTADDR_MASK) |
+ (ndev->dev_addr[4] |
+ (ndev->dev_addr[5] << 8))));
+}
+
+/**
+ * netdev_set_mac_address - Write the MAC address (from outside the driver)
+ * @ndev: Pointer to the net_device structure
+ * @p: 6 byte Address to be written as MAC address
+ *
+ * returns: 0 for all conditions. Presently, there is no failure case.
+ *
+ * This function is called to initialize the MAC address of the Axi Ethernet
+ * core. It calls the core specific axienet_set_mac_address. This is the
+ * function that goes into net_device_ops structure entry ndo_set_mac_address.
+ */
+static int netdev_set_mac_address(struct net_device *ndev, void *p)
+{
+ struct sockaddr *addr = p;
+ axienet_set_mac_address(ndev, addr->sa_data);
+ return 0;
+}
+
+/**
+ * axienet_set_multicast_list - Prepare the multicast table
+ * @ndev: Pointer to the net_device structure
+ *
+ * This function is called to initialize the multicast table during
+ * initialization. The Axi Ethernet basic multicast support has a four-entry
+ * multicast table which is initialized here. Additionally this function
+ * goes into the net_device_ops structure entry ndo_set_multicast_list. This
+ * means whenever the multicast table entries need to be updated this
+ * function gets called.
+ */
+static void axienet_set_multicast_list(struct net_device *ndev)
+{
+ int i;
+ u32 reg, af0reg, af1reg;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ if (ndev->flags & (IFF_ALLMULTI | IFF_PROMISC) ||
+ netdev_mc_count(ndev) > XAE_MULTICAST_CAM_TABLE_NUM) {
+ /* We must make the kernel realize we had to move into
+ * promiscuous mode. If it was a promiscuous mode request
+ * the flag is already set. If not we set it. */
+ ndev->flags |= IFF_PROMISC;
+ reg = axienet_ior(lp, XAE_FMI_OFFSET);
+ reg |= XAE_FMI_PM_MASK;
+ axienet_iow(lp, XAE_FMI_OFFSET, reg);
+ dev_info(&ndev->dev, "Promiscuous mode enabled.\n");
+ } else if (!netdev_mc_empty(ndev)) {
+ struct netdev_hw_addr *ha;
+
+ i = 0;
+ netdev_for_each_mc_addr(ha, ndev) {
+ if (i >= XAE_MULTICAST_CAM_TABLE_NUM)
+ break;
+
+ af0reg = (ha->addr[0]);
+ af0reg |= (ha->addr[1] << 8);
+ af0reg |= (ha->addr[2] << 16);
+ af0reg |= (ha->addr[3] << 24);
+
+ af1reg = (ha->addr[4]);
+ af1reg |= (ha->addr[5] << 8);
+
+ reg = axienet_ior(lp, XAE_FMI_OFFSET) & 0xFFFFFF00;
+ reg |= i;
+
+ axienet_iow(lp, XAE_FMI_OFFSET, reg);
+ axienet_iow(lp, XAE_AF0_OFFSET, af0reg);
+ axienet_iow(lp, XAE_AF1_OFFSET, af1reg);
+ i++;
+ }
+ } else {
+ reg = axienet_ior(lp, XAE_FMI_OFFSET);
+ reg &= ~XAE_FMI_PM_MASK;
+
+ axienet_iow(lp, XAE_FMI_OFFSET, reg);
+
+ for (i = 0; i < XAE_MULTICAST_CAM_TABLE_NUM; i++) {
+ reg = axienet_ior(lp, XAE_FMI_OFFSET) & 0xFFFFFF00;
+ reg |= i;
+
+ axienet_iow(lp, XAE_FMI_OFFSET, reg);
+ axienet_iow(lp, XAE_AF0_OFFSET, 0);
+ axienet_iow(lp, XAE_AF1_OFFSET, 0);
+ }
+
+ dev_info(&ndev->dev, "Promiscuous mode disabled.\n");
+ }
+}
+
+/**
+ * axienet_setoptions - Set an Axi Ethernet option
+ * @ndev: Pointer to the net_device structure
+ * @options: Option to be enabled/disabled
+ *
+ * The Axi Ethernet core has multiple features which can be selectively turned
+ * on or off. The typical options could be jumbo frame option, basic VLAN
+ * option, promiscuous mode option etc. This function is used to set or clear
+ * these options in the Axi Ethernet hardware. This is done through
+ * axienet_option structure .
+ */
+static void axienet_setoptions(struct net_device *ndev, u32 options)
+{
+ int reg;
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct axienet_option *tp = &axienet_options[0];
+
+ while (tp->opt) {
+ reg = ((axienet_ior(lp, tp->reg)) & ~(tp->m_or));
+ if (options & tp->opt)
+ reg |= tp->m_or;
+ axienet_iow(lp, tp->reg, reg);
+ tp++;
+ }
+
+ lp->options |= options;
+}
+
+static void __axienet_device_reset(struct axienet_local *lp,
+ struct device *dev, off_t offset)
+{
+ u32 timeout;
+ /* Reset Axi DMA. This would reset Axi Ethernet core as well. The reset
+ * process of Axi DMA takes a while to complete as all pending
+ * commands/transfers will be flushed or completed during this
+ * reset process. */
+ axienet_dma_out32(lp, offset, XAXIDMA_CR_RESET_MASK);
+ timeout = DELAY_OF_ONE_MILLISEC;
+ while (axienet_dma_in32(lp, offset) & XAXIDMA_CR_RESET_MASK) {
+ udelay(1);
+ if (--timeout == 0) {
+ dev_err(dev, "axienet_device_reset DMA "
+ "reset timeout!\n");
+ break;
+ }
+ }
+}
+
+/**
+ * axienet_device_reset - Reset and initialize the Axi Ethernet hardware.
+ * @ndev: Pointer to the net_device structure
+ *
+ * This function is called to reset and initialize the Axi Ethernet core. This
+ * is typically called during initialization. It does a reset of the Axi DMA
+ * Rx/Tx channels and initializes the Axi DMA BDs. Since Axi DMA reset lines
+ * areconnected to Axi Ethernet reset lines, this in turn resets the Axi
+ * Ethernet core. No separate hardware reset is done for the Axi Ethernet
+ * core.
+ */
+static void axienet_device_reset(struct net_device *ndev)
+{
+ u32 axienet_status;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ __axienet_device_reset(lp, &ndev->dev, XAXIDMA_TX_CR_OFFSET);
+ __axienet_device_reset(lp, &ndev->dev, XAXIDMA_RX_CR_OFFSET);
+
+ lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
+ lp->options &= (~XAE_OPTION_JUMBO);
+
+ if ((ndev->mtu > XAE_MTU) &&
+ (ndev->mtu <= XAE_JUMBO_MTU) &&
+ (lp->jumbo_support)) {
+ lp->max_frm_size = ndev->mtu + XAE_HDR_VLAN_SIZE +
+ XAE_TRL_SIZE;
+ lp->options |= XAE_OPTION_JUMBO;
+ }
+
+ if (axienet_dma_bd_init(ndev)) {
+ dev_err(&ndev->dev, "axienet_device_reset descriptor "
+ "allocation failed\n");
+ }
+
+ axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+ axienet_status &= ~XAE_RCW1_RX_MASK;
+ axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
+
+ axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+ if (axienet_status & XAE_INT_RXRJECT_MASK)
+ axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+
+ axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+
+ /* Sync default options with HW but leave receiver and
+ * transmitter disabled.*/
+ axienet_setoptions(ndev, lp->options &
+ ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+ axienet_set_mac_address(ndev, NULL);
+ axienet_set_multicast_list(ndev);
+ axienet_setoptions(ndev, lp->options);
+
+ ndev->trans_start = jiffies;
+}
+
+/**
+ * axienet_adjust_link - Adjust the PHY link speed/duplex.
+ * @ndev: Pointer to the net_device structure
+ *
+ * This function is called to change the speed and duplex setting after
+ * auto negotiation is done by the PHY. This is the function that gets
+ * registered with the PHY interface through the "of_phy_connect" call.
+ */
+static void axienet_adjust_link(struct net_device *ndev)
+{
+ u32 emmc_reg;
+ u32 link_state;
+ u32 setspeed = 1;
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct phy_device *phy = lp->phy_dev;
+
+ link_state = phy->speed | (phy->duplex << 1) | phy->link;
+ if (lp->last_link != link_state) {
+ if ((phy->speed == SPEED_10) || (phy->speed == SPEED_100)) {
+ if (lp->phy_type == XAE_PHY_TYPE_1000BASE_X)
+ setspeed = 0;
+ } else {
+ if ((phy->speed == SPEED_1000) &&
+ (lp->phy_type == XAE_PHY_TYPE_MII))
+ setspeed = 0;
+ }
+
+ if (setspeed == 1) {
+ emmc_reg = axienet_ior(lp, XAE_EMMC_OFFSET);
+ emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
+
+ switch (phy->speed) {
+ case SPEED_1000:
+ emmc_reg |= XAE_EMMC_LINKSPD_1000;
+ break;
+ case SPEED_100:
+ emmc_reg |= XAE_EMMC_LINKSPD_100;
+ break;
+ case SPEED_10:
+ emmc_reg |= XAE_EMMC_LINKSPD_10;
+ break;
+ default:
+ dev_err(&ndev->dev, "Speed other than 10, 100 "
+ "or 1Gbps is not supported\n");
+ break;
+ }
+
+ axienet_iow(lp, XAE_EMMC_OFFSET, emmc_reg);
+ lp->last_link = link_state;
+ phy_print_status(phy);
+ } else {
+ dev_err(&ndev->dev, "Error setting Axi Ethernet "
+ "mac speed\n");
+ }
+ }
+}
+
+/**
+ * axienet_start_xmit_done - Invoked once a transmit is completed by the
+ * Axi DMA Tx channel.
+ * @ndev: Pointer to the net_device structure
+ *
+ * This function is invoked from the Axi DMA Tx isr to notify the completion
+ * of transmit operation. It clears fields in the corresponding Tx BDs and
+ * unmaps the corresponding buffer so that CPU can regain ownership of the
+ * buffer. It finally invokes "netif_wake_queue" to restart transmission if
+ * required.
+ */
+static void axienet_start_xmit_done(struct net_device *ndev)
+{
+ u32 size = 0;
+ u32 packets = 0;
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct axidma_bd *cur_p;
+ unsigned int status = 0;
+
+ cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
+ status = cur_p->status;
+ while (status & XAXIDMA_BD_STS_COMPLETE_MASK) {
+ dma_unmap_single(ndev->dev.parent, cur_p->phys,
+ (cur_p->cntrl & XAXIDMA_BD_CTRL_LENGTH_MASK),
+ DMA_TO_DEVICE);
+ if (cur_p->app4)
+ dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
+ /*cur_p->phys = 0;*/
+ cur_p->app0 = 0;
+ cur_p->app1 = 0;
+ cur_p->app2 = 0;
+ cur_p->app4 = 0;
+ cur_p->status = 0;
+
+ size += status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
+ packets++;
+
+ lp->tx_bd_ci = ++lp->tx_bd_ci % TX_BD_NUM;
+ cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
+ status = cur_p->status;
+ }
+
+ ndev->stats.tx_packets += packets;
+ ndev->stats.tx_bytes += size;
+ netif_wake_queue(ndev);
+}
+
+/**
+ * axienet_check_tx_bd_space - Checks if a BD/group of BDs are currently busy
+ * @lp: Pointer to the axienet_local structure
+ * @num_frag: The number of BDs to check for
+ *
+ * returns: 0, on success
+ * NETDEV_TX_BUSY, if any of the descriptors are not free
+ *
+ * This function is invoked before BDs are allocated and transmission starts.
+ * This function returns 0 if a BD or group of BDs can be allocated for
+ * transmission. If the BD or any of the BDs are not free the function
+ * returns a busy status. This is invoked from axienet_start_xmit.
+ */
+static inline int axienet_check_tx_bd_space(struct axienet_local *lp,
+ int num_frag)
+{
+ struct axidma_bd *cur_p;
+ cur_p = &lp->tx_bd_v[(lp->tx_bd_tail + num_frag) % TX_BD_NUM];
+ if (cur_p->status & XAXIDMA_BD_STS_ALL_MASK)
+ return NETDEV_TX_BUSY;
+ return 0;
+}
+
+/**
+ * axienet_start_xmit - Starts the transmission.
+ * @skb: sk_buff pointer that contains data to be Txed.
+ * @ndev: Pointer to net_device structure.
+ *
+ * returns: NETDEV_TX_OK, on success
+ * NETDEV_TX_BUSY, if any of the descriptors are not free
+ *
+ * This function is invoked from upper layers to initiate transmission. The
+ * function uses the next available free BDs and populates their fields to
+ * start the transmission. Additionally if checksum offloading is supported,
+ * it populates AXI Stream Control fields with appropriate values.
+ */
+static int axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ u32 ii;
+ u32 num_frag;
+ u32 csum_start_off;
+ u32 csum_index_off;
+ skb_frag_t *frag;
+ dma_addr_t tail_p;
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct axidma_bd *cur_p;
+
+ num_frag = skb_shinfo(skb)->nr_frags;
+ cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
+
+ if (axienet_check_tx_bd_space(lp, num_frag)) {
+ if (!netif_queue_stopped(ndev))
+ netif_stop_queue(ndev);
+ return NETDEV_TX_BUSY;
+ }
+
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ if (lp->features & XAE_FEATURE_FULL_TX_CSUM) {
+ /* Tx Full Checksum Offload Enabled */
+ cur_p->app0 |= 2;
+ } else if (lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) {
+ csum_start_off = skb_transport_offset(skb);
+ csum_index_off = csum_start_off + skb->csum_offset;
+ /* Tx Partial Checksum Offload Enabled */
+ cur_p->app0 |= 1;
+ cur_p->app1 = (csum_start_off << 16) | csum_index_off;
+ }
+ } else if (skb->ip_summed == CHECKSUM_UNNECESSARY) {
+ cur_p->app0 |= 2; /* Tx Full Checksum Offload Enabled */
+ }
+
+ cur_p->cntrl = skb_headlen(skb) | XAXIDMA_BD_CTRL_TXSOF_MASK;
+ cur_p->phys = dma_map_single(ndev->dev.parent, skb->data,
+ skb_headlen(skb), DMA_TO_DEVICE);
+
+ for (ii = 0; ii < num_frag; ii++) {
+ lp->tx_bd_tail = ++lp->tx_bd_tail % TX_BD_NUM;
+ cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
+ frag = &skb_shinfo(skb)->frags[ii];
+ cur_p->phys = dma_map_single(ndev->dev.parent,
+ skb_frag_address(frag),
+ skb_frag_size(frag),
+ DMA_TO_DEVICE);
+ cur_p->cntrl = skb_frag_size(frag);
+ }
+
+ cur_p->cntrl |= XAXIDMA_BD_CTRL_TXEOF_MASK;
+ cur_p->app4 = (unsigned long)skb;
+
+ tail_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
+ /* Start the transfer */
+ axienet_dma_out32(lp, XAXIDMA_TX_TDESC_OFFSET, tail_p);
+ lp->tx_bd_tail = ++lp->tx_bd_tail % TX_BD_NUM;
+
+ return NETDEV_TX_OK;
+}
+
+/**
+ * axienet_recv - Is called from Axi DMA Rx Isr to complete the received
+ * BD processing.
+ * @ndev: Pointer to net_device structure.
+ *
+ * This function is invoked from the Axi DMA Rx isr to process the Rx BDs. It
+ * does minimal processing and invokes "netif_rx" to complete further
+ * processing.
+ */
+static void axienet_recv(struct net_device *ndev)
+{
+ u32 length;
+ u32 csumstatus;
+ u32 size = 0;
+ u32 packets = 0;
+ dma_addr_t tail_p;
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct sk_buff *skb, *new_skb;
+ struct axidma_bd *cur_p;
+
+ tail_p = lp->rx_bd_p + sizeof(*lp->rx_bd_v) * lp->rx_bd_ci;
+ cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
+
+ while ((cur_p->status & XAXIDMA_BD_STS_COMPLETE_MASK)) {
+ skb = (struct sk_buff *) (cur_p->sw_id_offset);
+ length = cur_p->app4 & 0x0000FFFF;
+
+ dma_unmap_single(ndev->dev.parent, cur_p->phys,
+ lp->max_frm_size,
+ DMA_FROM_DEVICE);
+
+ skb_put(skb, length);
+ skb->protocol = eth_type_trans(skb, ndev);
+ /*skb_checksum_none_assert(skb);*/
+ skb->ip_summed = CHECKSUM_NONE;
+
+ /* if we're doing Rx csum offload, set it up */
+ if (lp->features & XAE_FEATURE_FULL_RX_CSUM) {
+ csumstatus = (cur_p->app2 &
+ XAE_FULL_CSUM_STATUS_MASK) >> 3;
+ if ((csumstatus == XAE_IP_TCP_CSUM_VALIDATED) ||
+ (csumstatus == XAE_IP_UDP_CSUM_VALIDATED)) {
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ }
+ } else if ((lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) != 0 &&
+ skb->protocol == __constant_htons(ETH_P_IP) &&
+ skb->len > 64) {
+ skb->csum = be32_to_cpu(cur_p->app3 & 0xFFFF);
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ }
+
+ netif_rx(skb);
+
+ size += length;
+ packets++;
+
+ new_skb = netdev_alloc_skb_ip_align(ndev, lp->max_frm_size);
+ if (!new_skb) {
+ dev_err(&ndev->dev, "no memory for new sk_buff\n");
+ return;
+ }
+ cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
+ lp->max_frm_size,
+ DMA_FROM_DEVICE);
+ cur_p->cntrl = lp->max_frm_size;
+ cur_p->status = 0;
+ cur_p->sw_id_offset = (u32) new_skb;
+
+ lp->rx_bd_ci = ++lp->rx_bd_ci % RX_BD_NUM;
+ cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
+ }
+
+ ndev->stats.rx_packets += packets;
+ ndev->stats.rx_bytes += size;
+
+ axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, tail_p);
+}
+
+/**
+ * axienet_tx_irq - Tx Done Isr.
+ * @irq: irq number
+ * @_ndev: net_device pointer
+ *
+ * returns: IRQ_HANDLED for all cases.
+ *
+ * This is the Axi DMA Tx done Isr. It invokes "axienet_start_xmit_done"
+ * to complete the BD processing.
+ */
+static irqreturn_t axienet_tx_irq(int irq, void *_ndev)
+{
+ u32 cr;
+ unsigned int status;
+ struct net_device *ndev = _ndev;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ status = axienet_dma_in32(lp, XAXIDMA_TX_SR_OFFSET);
+ if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+ axienet_start_xmit_done(lp->ndev);
+ goto out;
+ }
+ if (!(status & XAXIDMA_IRQ_ALL_MASK))
+ dev_err(&ndev->dev, "No interrupts asserted in Tx path");
+ if (status & XAXIDMA_IRQ_ERROR_MASK) {
+ dev_err(&ndev->dev, "DMA Tx error 0x%x\n", status);
+ dev_err(&ndev->dev, "Current BD is at: 0x%x\n",
+ (lp->tx_bd_v[lp->tx_bd_ci]).phys);
+
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* Write to the Tx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
+
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* Write to the Rx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
+
+ tasklet_schedule(&lp->dma_err_tasklet);
+ }
+out:
+ axienet_dma_out32(lp, XAXIDMA_TX_SR_OFFSET, status);
+ return IRQ_HANDLED;
+}
+
+/**
+ * axienet_rx_irq - Rx Isr.
+ * @irq: irq number
+ * @_ndev: net_device pointer
+ *
+ * returns: IRQ_HANDLED for all cases.
+ *
+ * This is the Axi DMA Rx Isr. It invokes "axienet_recv" to complete the BD
+ * processing.
+ */
+static irqreturn_t axienet_rx_irq(int irq, void *_ndev)
+{
+ u32 cr;
+ unsigned int status;
+ struct net_device *ndev = _ndev;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ status = axienet_dma_in32(lp, XAXIDMA_RX_SR_OFFSET);
+ if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
+ axienet_recv(lp->ndev);
+ goto out;
+ }
+ if (!(status & XAXIDMA_IRQ_ALL_MASK))
+ dev_err(&ndev->dev, "No interrupts asserted in Rx path");
+ if (status & XAXIDMA_IRQ_ERROR_MASK) {
+ dev_err(&ndev->dev, "DMA Rx error 0x%x\n", status);
+ dev_err(&ndev->dev, "Current BD is at: 0x%x\n",
+ (lp->rx_bd_v[lp->rx_bd_ci]).phys);
+
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* Finally write to the Tx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
+
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ /* Disable coalesce, delay timer and error interrupts */
+ cr &= (~XAXIDMA_IRQ_ALL_MASK);
+ /* write to the Rx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
+
+ tasklet_schedule(&lp->dma_err_tasklet);
+ }
+out:
+ axienet_dma_out32(lp, XAXIDMA_RX_SR_OFFSET, status);
+ return IRQ_HANDLED;
+}
+
+/**
+ * axienet_open - Driver open routine.
+ * @ndev: Pointer to net_device structure
+ *
+ * returns: 0, on success.
+ * -ENODEV, if PHY cannot be connected to
+ * non-zero error value on failure
+ *
+ * This is the driver open routine. It calls phy_start to start the PHY device.
+ * It also allocates interrupt service routines, enables the interrupt lines
+ * and ISR handling. Axi Ethernet core is reset through Axi DMA core. Buffer
+ * descriptors are initialized.
+ */
+static int axienet_open(struct net_device *ndev)
+{
+ int ret, mdio_mcreg;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ dev_dbg(&ndev->dev, "axienet_open()\n");
+
+ mdio_mcreg = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+ /* Disable the MDIO interface till Axi Ethernet Reset is completed.
+ * When we do an Axi Ethernet reset, it resets the complete core
+ * including the MDIO. If MDIO is not disabled when the reset
+ * process is started, MDIO will be broken afterwards. */
+ axienet_iow(lp, XAE_MDIO_MC_OFFSET,
+ (mdio_mcreg & (~XAE_MDIO_MC_MDIOEN_MASK)));
+ axienet_device_reset(ndev);
+ /* Enable the MDIO */
+ axienet_iow(lp, XAE_MDIO_MC_OFFSET, mdio_mcreg);
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+
+ if (lp->phy_node) {
+ lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node,
+ axienet_adjust_link, 0,
+ PHY_INTERFACE_MODE_GMII);
+ if (!lp->phy_dev) {
+ dev_err(lp->dev, "of_phy_connect() failed\n");
+ return -ENODEV;
+ }
+ phy_start(lp->phy_dev);
+ }
+
+ /* Enable interrupts for Axi DMA Tx */
+ ret = request_irq(lp->tx_irq, axienet_tx_irq, 0, ndev->name, ndev);
+ if (ret)
+ goto err_tx_irq;
+ /* Enable interrupts for Axi DMA Rx */
+ ret = request_irq(lp->rx_irq, axienet_rx_irq, 0, ndev->name, ndev);
+ if (ret)
+ goto err_rx_irq;
+ /* Enable tasklets for Axi DMA error handling */
+ tasklet_enable(&lp->dma_err_tasklet);
+ return 0;
+
+err_rx_irq:
+ free_irq(lp->tx_irq, ndev);
+err_tx_irq:
+ if (lp->phy_dev)
+ phy_disconnect(lp->phy_dev);
+ lp->phy_dev = NULL;
+ dev_err(lp->dev, "request_irq() failed\n");
+ return ret;
+}
+
+/**
+ * axienet_stop - Driver stop routine.
+ * @ndev: Pointer to net_device structure
+ *
+ * returns: 0, on success.
+ *
+ * This is the driver stop routine. It calls phy_disconnect to stop the PHY
+ * device. It also removes the interrupt handlers and disables the interrupts.
+ * The Axi DMA Tx/Rx BDs are released.
+ */
+static int axienet_stop(struct net_device *ndev)
+{
+ u32 cr;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ dev_dbg(&ndev->dev, "axienet_close()\n");
+
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
+ cr & (~XAXIDMA_CR_RUNSTOP_MASK));
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
+ cr & (~XAXIDMA_CR_RUNSTOP_MASK));
+ axienet_setoptions(ndev, lp->options &
+ ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+
+ tasklet_disable(&lp->dma_err_tasklet);
+
+ free_irq(lp->tx_irq, ndev);
+ free_irq(lp->rx_irq, ndev);
+
+ if (lp->phy_dev)
+ phy_disconnect(lp->phy_dev);
+ lp->phy_dev = NULL;
+
+ axienet_dma_bd_release(ndev);
+ return 0;
+}
+
+/**
+ * axienet_change_mtu - Driver change mtu routine.
+ * @ndev: Pointer to net_device structure
+ * @new_mtu: New mtu value to be applied
+ *
+ * returns: Always returns 0 (success).
+ *
+ * This is the change mtu driver routine. It checks if the Axi Ethernet
+ * hardware supports jumbo frames before changing the mtu. This can be
+ * called only when the device is not up.
+ */
+static int axienet_change_mtu(struct net_device *ndev, int new_mtu)
+{
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ if (netif_running(ndev))
+ return -EBUSY;
+ if (lp->jumbo_support) {
+ if ((new_mtu > XAE_JUMBO_MTU) || (new_mtu < 64))
+ return -EINVAL;
+ ndev->mtu = new_mtu;
+ } else {
+ if ((new_mtu > XAE_MTU) || (new_mtu < 64))
+ return -EINVAL;
+ ndev->mtu = new_mtu;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/**
+ * axienet_poll_controller - Axi Ethernet poll mechanism.
+ * @ndev: Pointer to net_device structure
+ *
+ * This implements Rx/Tx ISR poll mechanisms. The interrupts are disabled prior
+ * to polling the ISRs and are enabled back after the polling is done.
+ */
+static void axienet_poll_controller(struct net_device *ndev)
+{
+ struct axienet_local *lp = netdev_priv(ndev);
+ disable_irq(lp->tx_irq);
+ disable_irq(lp->rx_irq);
+ axienet_rx_irq(lp->tx_irq, ndev);
+ axienet_tx_irq(lp->rx_irq, ndev);
+ enable_irq(lp->tx_irq);
+ enable_irq(lp->rx_irq);
+}
+#endif
+
+static const struct net_device_ops axienet_netdev_ops = {
+ .ndo_open = axienet_open,
+ .ndo_stop = axienet_stop,
+ .ndo_start_xmit = axienet_start_xmit,
+ .ndo_change_mtu = axienet_change_mtu,
+ .ndo_set_mac_address = netdev_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_rx_mode = axienet_set_multicast_list,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = axienet_poll_controller,
+#endif
+};
+
+/**
+ * axienet_ethtools_get_settings - Get Axi Ethernet settings related to PHY.
+ * @ndev: Pointer to net_device structure
+ * @ecmd: Pointer to ethtool_cmd structure
+ *
+ * This implements ethtool command for getting PHY settings. If PHY could
+ * not be found, the function returns -ENODEV. This function calls the
+ * relevant PHY ethtool API to get the PHY settings.
+ * Issue "ethtool ethX" under linux prompt to execute this function.
+ */
+static int axienet_ethtools_get_settings(struct net_device *ndev,
+ struct ethtool_cmd *ecmd)
+{
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct phy_device *phydev = lp->phy_dev;
+ if (!phydev)
+ return -ENODEV;
+ return phy_ethtool_gset(phydev, ecmd);
+}
+
+/**
+ * axienet_ethtools_set_settings - Set PHY settings as passed in the argument.
+ * @ndev: Pointer to net_device structure
+ * @ecmd: Pointer to ethtool_cmd structure
+ *
+ * This implements ethtool command for setting various PHY settings. If PHY
+ * could not be found, the function returns -ENODEV. This function calls the
+ * relevant PHY ethtool API to set the PHY.
+ * Issue e.g. "ethtool -s ethX speed 1000" under linux prompt to execute this
+ * function.
+ */
+static int axienet_ethtools_set_settings(struct net_device *ndev,
+ struct ethtool_cmd *ecmd)
+{
+ struct axienet_local *lp = netdev_priv(ndev);
+ struct phy_device *phydev = lp->phy_dev;
+ if (!phydev)
+ return -ENODEV;
+ return phy_ethtool_sset(phydev, ecmd);
+}
+
+/**
+ * axienet_ethtools_get_drvinfo - Get various Axi Ethernet driver information.
+ * @ndev: Pointer to net_device structure
+ * @ed: Pointer to ethtool_drvinfo structure
+ *
+ * This implements ethtool command for getting the driver information.
+ * Issue "ethtool -i ethX" under linux prompt to execute this function.
+ */
+static void axienet_ethtools_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *ed)
+{
+ memset(ed, 0, sizeof(struct ethtool_drvinfo));
+ strcpy(ed->driver, DRIVER_NAME);
+ strcpy(ed->version, DRIVER_VERSION);
+ ed->regdump_len = sizeof(u32) * AXIENET_REGS_N;
+}
+
+/**
+ * axienet_ethtools_get_regs_len - Get the total regs length present in the
+ * AxiEthernet core.
+ * @ndev: Pointer to net_device structure
+ *
+ * This implements ethtool command for getting the total register length
+ * information.
+ */
+static int axienet_ethtools_get_regs_len(struct net_device *ndev)
+{
+ return sizeof(u32) * AXIENET_REGS_N;
+}
+
+/**
+ * axienet_ethtools_get_regs - Dump the contents of all registers present
+ * in AxiEthernet core.
+ * @ndev: Pointer to net_device structure
+ * @regs: Pointer to ethtool_regs structure
+ * @ret: Void pointer used to return the contents of the registers.
+ *
+ * This implements ethtool command for getting the Axi Ethernet register dump.
+ * Issue "ethtool -d ethX" to execute this function.
+ */
+static void axienet_ethtools_get_regs(struct net_device *ndev,
+ struct ethtool_regs *regs, void *ret)
+{
+ u32 *data = (u32 *) ret;
+ size_t len = sizeof(u32) * AXIENET_REGS_N;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ regs->version = 0;
+ regs->len = len;
+
+ memset(data, 0, len);
+ data[0] = axienet_ior(lp, XAE_RAF_OFFSET);
+ data[1] = axienet_ior(lp, XAE_TPF_OFFSET);
+ data[2] = axienet_ior(lp, XAE_IFGP_OFFSET);
+ data[3] = axienet_ior(lp, XAE_IS_OFFSET);
+ data[4] = axienet_ior(lp, XAE_IP_OFFSET);
+ data[5] = axienet_ior(lp, XAE_IE_OFFSET);
+ data[6] = axienet_ior(lp, XAE_TTAG_OFFSET);
+ data[7] = axienet_ior(lp, XAE_RTAG_OFFSET);
+ data[8] = axienet_ior(lp, XAE_UAWL_OFFSET);
+ data[9] = axienet_ior(lp, XAE_UAWU_OFFSET);
+ data[10] = axienet_ior(lp, XAE_TPID0_OFFSET);
+ data[11] = axienet_ior(lp, XAE_TPID1_OFFSET);
+ data[12] = axienet_ior(lp, XAE_PPST_OFFSET);
+ data[13] = axienet_ior(lp, XAE_RCW0_OFFSET);
+ data[14] = axienet_ior(lp, XAE_RCW1_OFFSET);
+ data[15] = axienet_ior(lp, XAE_TC_OFFSET);
+ data[16] = axienet_ior(lp, XAE_FCC_OFFSET);
+ data[17] = axienet_ior(lp, XAE_EMMC_OFFSET);
+ data[18] = axienet_ior(lp, XAE_PHYC_OFFSET);
+ data[19] = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
+ data[20] = axienet_ior(lp, XAE_MDIO_MCR_OFFSET);
+ data[21] = axienet_ior(lp, XAE_MDIO_MWD_OFFSET);
+ data[22] = axienet_ior(lp, XAE_MDIO_MRD_OFFSET);
+ data[23] = axienet_ior(lp, XAE_MDIO_MIS_OFFSET);
+ data[24] = axienet_ior(lp, XAE_MDIO_MIP_OFFSET);
+ data[25] = axienet_ior(lp, XAE_MDIO_MIE_OFFSET);
+ data[26] = axienet_ior(lp, XAE_MDIO_MIC_OFFSET);
+ data[27] = axienet_ior(lp, XAE_UAW0_OFFSET);
+ data[28] = axienet_ior(lp, XAE_UAW1_OFFSET);
+ data[29] = axienet_ior(lp, XAE_FMI_OFFSET);
+ data[30] = axienet_ior(lp, XAE_AF0_OFFSET);
+ data[31] = axienet_ior(lp, XAE_AF1_OFFSET);
+}
+
+/**
+ * axienet_ethtools_get_pauseparam - Get the pause parameter setting for
+ * Tx and Rx paths.
+ * @ndev: Pointer to net_device structure
+ * @epauseparm: Pointer to ethtool_pauseparam structure.
+ *
+ * This implements ethtool command for getting axi ethernet pause frame
+ * setting. Issue "ethtool -a ethX" to execute this function.
+ */
+static void
+axienet_ethtools_get_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *epauseparm)
+{
+ u32 regval;
+ struct axienet_local *lp = netdev_priv(ndev);
+ epauseparm->autoneg = 0;
+ regval = axienet_ior(lp, XAE_FCC_OFFSET);
+ epauseparm->tx_pause = regval & XAE_FCC_FCTX_MASK;
+ epauseparm->rx_pause = regval & XAE_FCC_FCRX_MASK;
+}
+
+/**
+ * axienet_ethtools_set_pauseparam - Set device pause parameter(flow control)
+ * settings.
+ * @ndev: Pointer to net_device structure
+ * @epauseparam:Pointer to ethtool_pauseparam structure
+ *
+ * This implements ethtool command for enabling flow control on Rx and Tx
+ * paths. Issue "ethtool -A ethX tx on|off" under linux prompt to execute this
+ * function.
+ */
+static int
+axienet_ethtools_set_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *epauseparm)
+{
+ u32 regval = 0;
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ printk(KERN_ERR "%s: Please stop netif before applying "
+ "configruation\n", ndev->name);
+ return -EFAULT;
+ }
+
+ regval = axienet_ior(lp, XAE_FCC_OFFSET);
+ if (epauseparm->tx_pause)
+ regval |= XAE_FCC_FCTX_MASK;
+ else
+ regval &= ~XAE_FCC_FCTX_MASK;
+ if (epauseparm->rx_pause)
+ regval |= XAE_FCC_FCRX_MASK;
+ else
+ regval &= ~XAE_FCC_FCRX_MASK;
+ axienet_iow(lp, XAE_FCC_OFFSET, regval);
+
+ return 0;
+}
+
+/**
+ * axienet_ethtools_get_coalesce - Get DMA interrupt coalescing count.
+ * @ndev: Pointer to net_device structure
+ * @ecoalesce: Pointer to ethtool_coalesce structure
+ *
+ * This implements ethtool command for getting the DMA interrupt coalescing
+ * count on Tx and Rx paths. Issue "ethtool -c ethX" under linux prompt to
+ * execute this function.
+ */
+static int axienet_ethtools_get_coalesce(struct net_device *ndev,
+ struct ethtool_coalesce *ecoalesce)
+{
+ u32 regval = 0;
+ struct axienet_local *lp = netdev_priv(ndev);
+ regval = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ ecoalesce->rx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
+ >> XAXIDMA_COALESCE_SHIFT;
+ regval = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ ecoalesce->tx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
+ >> XAXIDMA_COALESCE_SHIFT;
+ return 0;
+}
+
+/**
+ * axienet_ethtools_set_coalesce - Set DMA interrupt coalescing count.
+ * @ndev: Pointer to net_device structure
+ * @ecoalesce: Pointer to ethtool_coalesce structure
+ *
+ * This implements ethtool command for setting the DMA interrupt coalescing
+ * count on Tx and Rx paths. Issue "ethtool -C ethX rx-frames 5" under linux
+ * prompt to execute this function.
+ */
+static int axienet_ethtools_set_coalesce(struct net_device *ndev,
+ struct ethtool_coalesce *ecoalesce)
+{
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ printk(KERN_ERR "%s: Please stop netif before applying "
+ "configruation\n", ndev->name);
+ return -EFAULT;
+ }
+
+ if ((ecoalesce->rx_coalesce_usecs) ||
+ (ecoalesce->rx_coalesce_usecs_irq) ||
+ (ecoalesce->rx_max_coalesced_frames_irq) ||
+ (ecoalesce->tx_coalesce_usecs) ||
+ (ecoalesce->tx_coalesce_usecs_irq) ||
+ (ecoalesce->tx_max_coalesced_frames_irq) ||
+ (ecoalesce->stats_block_coalesce_usecs) ||
+ (ecoalesce->use_adaptive_rx_coalesce) ||
+ (ecoalesce->use_adaptive_tx_coalesce) ||
+ (ecoalesce->pkt_rate_low) ||
+ (ecoalesce->rx_coalesce_usecs_low) ||
+ (ecoalesce->rx_max_coalesced_frames_low) ||
+ (ecoalesce->tx_coalesce_usecs_low) ||
+ (ecoalesce->tx_max_coalesced_frames_low) ||
+ (ecoalesce->pkt_rate_high) ||
+ (ecoalesce->rx_coalesce_usecs_high) ||
+ (ecoalesce->rx_max_coalesced_frames_high) ||
+ (ecoalesce->tx_coalesce_usecs_high) ||
+ (ecoalesce->tx_max_coalesced_frames_high) ||
+ (ecoalesce->rate_sample_interval))
+ return -EOPNOTSUPP;
+ if (ecoalesce->rx_max_coalesced_frames)
+ lp->coalesce_count_rx = ecoalesce->rx_max_coalesced_frames;
+ if (ecoalesce->tx_max_coalesced_frames)
+ lp->coalesce_count_tx = ecoalesce->tx_max_coalesced_frames;
+
+ return 0;
+}
+
+static struct ethtool_ops axienet_ethtool_ops = {
+ .get_settings = axienet_ethtools_get_settings,
+ .set_settings = axienet_ethtools_set_settings,
+ .get_drvinfo = axienet_ethtools_get_drvinfo,
+ .get_regs_len = axienet_ethtools_get_regs_len,
+ .get_regs = axienet_ethtools_get_regs,
+ .get_link = ethtool_op_get_link,
+ .get_pauseparam = axienet_ethtools_get_pauseparam,
+ .set_pauseparam = axienet_ethtools_set_pauseparam,
+ .get_coalesce = axienet_ethtools_get_coalesce,
+ .set_coalesce = axienet_ethtools_set_coalesce,
+};
+
+/**
+ * axienet_dma_err_handler - Tasklet handler for Axi DMA Error
+ * @data: Data passed
+ *
+ * Resets the Axi DMA and Axi Ethernet devices, and reconfigures the
+ * Tx/Rx BDs.
+ */
+static void axienet_dma_err_handler(unsigned long data)
+{
+ u32 axienet_status;
+ u32 cr, i;
+ int mdio_mcreg;
+ struct axienet_local *lp = (struct axienet_local *) data;
+ struct net_device *ndev = lp->ndev;
+ struct axidma_bd *cur_p;
+
+ axienet_setoptions(ndev, lp->options &
+ ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+ mdio_mcreg = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
+ axienet_mdio_wait_until_ready(lp);
+ /* Disable the MDIO interface till Axi Ethernet Reset is completed.
+ * When we do an Axi Ethernet reset, it resets the complete core
+ * including the MDIO. So if MDIO is not disabled when the reset
+ * process is started, MDIO will be broken afterwards. */
+ axienet_iow(lp, XAE_MDIO_MC_OFFSET, (mdio_mcreg &
+ ~XAE_MDIO_MC_MDIOEN_MASK));
+
+ __axienet_device_reset(lp, &ndev->dev, XAXIDMA_TX_CR_OFFSET);
+ __axienet_device_reset(lp, &ndev->dev, XAXIDMA_RX_CR_OFFSET);
+
+ axienet_iow(lp, XAE_MDIO_MC_OFFSET, mdio_mcreg);
+ axienet_mdio_wait_until_ready(lp);
+
+ for (i = 0; i < TX_BD_NUM; i++) {
+ cur_p = &lp->tx_bd_v[i];
+ if (cur_p->phys)
+ dma_unmap_single(ndev->dev.parent, cur_p->phys,
+ (cur_p->cntrl &
+ XAXIDMA_BD_CTRL_LENGTH_MASK),
+ DMA_TO_DEVICE);
+ if (cur_p->app4)
+ dev_kfree_skb_irq((struct sk_buff *) cur_p->app4);
+ cur_p->phys = 0;
+ cur_p->cntrl = 0;
+ cur_p->status = 0;
+ cur_p->app0 = 0;
+ cur_p->app1 = 0;
+ cur_p->app2 = 0;
+ cur_p->app3 = 0;
+ cur_p->app4 = 0;
+ cur_p->sw_id_offset = 0;
+ }
+
+ for (i = 0; i < RX_BD_NUM; i++) {
+ cur_p = &lp->rx_bd_v[i];
+ cur_p->status = 0;
+ cur_p->app0 = 0;
+ cur_p->app1 = 0;
+ cur_p->app2 = 0;
+ cur_p->app3 = 0;
+ cur_p->app4 = 0;
+ }
+
+ lp->tx_bd_ci = 0;
+ lp->tx_bd_tail = 0;
+ lp->rx_bd_ci = 0;
+
+ /* Start updating the Rx channel control register */
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
+ (XAXIDMA_DFT_RX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = ((cr & ~XAXIDMA_DELAY_MASK) |
+ (XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Finally write to the Rx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
+
+ /* Start updating the Tx channel control register */
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ /* Update the interrupt coalesce count */
+ cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
+ (XAXIDMA_DFT_TX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
+ /* Update the delay timer count */
+ cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
+ (XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
+ /* Enable coalesce, delay timer and error interrupts */
+ cr |= XAXIDMA_IRQ_ALL_MASK;
+ /* Finally write to the Tx channel control register */
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
+
+ /* Populate the tail pointer and bring the Rx Axi DMA engine out of
+ * halted state. This will make the Rx side ready for reception.*/
+ axienet_dma_out32(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
+ cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
+ axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+ axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
+ (sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
+
+ /* Write to the RS (Run-stop) bit in the Tx channel control register.
+ * Tx channel is now ready to run. But only after we write to the
+ * tail pointer register that the Tx channel will start transmitting */
+ axienet_dma_out32(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
+ cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
+ axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
+ cr | XAXIDMA_CR_RUNSTOP_MASK);
+
+ axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
+ axienet_status &= ~XAE_RCW1_RX_MASK;
+ axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
+
+ axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
+ if (axienet_status & XAE_INT_RXRJECT_MASK)
+ axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
+ axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
+
+ /* Sync default options with HW but leave receiver and
+ * transmitter disabled.*/
+ axienet_setoptions(ndev, lp->options &
+ ~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
+ axienet_set_mac_address(ndev, NULL);
+ axienet_set_multicast_list(ndev);
+ axienet_setoptions(ndev, lp->options);
+}
+
+/**
+ * axienet_of_probe - Axi Ethernet probe function.
+ * @op: Pointer to platform device structure.
+ * @match: Pointer to device id structure
+ *
+ * returns: 0, on success
+ * Non-zero error value on failure.
+ *
+ * This is the probe routine for Axi Ethernet driver. This is called before
+ * any other driver routines are invoked. It allocates and sets up the Ethernet
+ * device. Parses through device tree and populates fields of
+ * axienet_local. It registers the Ethernet device.
+ */
+static int __devinit axienet_of_probe(struct platform_device *op)
+{
+ __be32 *p;
+ int size, ret = 0;
+ struct device_node *np;
+ struct axienet_local *lp;
+ struct net_device *ndev;
+ const void *addr;
+
+ ndev = alloc_etherdev(sizeof(*lp));
+ if (!ndev) {
+ dev_err(&op->dev, "could not allocate device.\n");
+ return -ENOMEM;
+ }
+
+ ether_setup(ndev);
+ dev_set_drvdata(&op->dev, ndev);
+
+ SET_NETDEV_DEV(ndev, &op->dev);
+ ndev->flags &= ~IFF_MULTICAST; /* clear multicast */
+ ndev->features = NETIF_F_SG | NETIF_F_FRAGLIST;
+ ndev->netdev_ops = &axienet_netdev_ops;
+ ndev->ethtool_ops = &axienet_ethtool_ops;
+
+ lp = netdev_priv(ndev);
+ lp->ndev = ndev;
+ lp->dev = &op->dev;
+ lp->options = XAE_OPTION_DEFAULTS;
+ /* Map device registers */
+ lp->regs = of_iomap(op->dev.of_node, 0);
+ if (!lp->regs) {
+ dev_err(&op->dev, "could not map Axi Ethernet regs.\n");
+ goto nodev;
+ }
+ /* Setup checksum offload, but default to off if not specified */
+ lp->features = 0;
+
+ p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,txcsum", NULL);
+ if (p) {
+ switch (be32_to_cpup(p)) {
+ case 1:
+ lp->csum_offload_on_tx_path =
+ XAE_FEATURE_PARTIAL_TX_CSUM;
+ lp->features |= XAE_FEATURE_PARTIAL_TX_CSUM;
+ /* Can checksum TCP/UDP over IPv4. */
+ ndev->features |= NETIF_F_IP_CSUM;
+ break;
+ case 2:
+ lp->csum_offload_on_tx_path =
+ XAE_FEATURE_FULL_TX_CSUM;
+ lp->features |= XAE_FEATURE_FULL_TX_CSUM;
+ /* Can checksum TCP/UDP over IPv4. */
+ ndev->features |= NETIF_F_IP_CSUM;
+ break;
+ default:
+ lp->csum_offload_on_tx_path = XAE_NO_CSUM_OFFLOAD;
+ }
+ }
+ p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,rxcsum", NULL);
+ if (p) {
+ switch (be32_to_cpup(p)) {
+ case 1:
+ lp->csum_offload_on_rx_path =
+ XAE_FEATURE_PARTIAL_RX_CSUM;
+ lp->features |= XAE_FEATURE_PARTIAL_RX_CSUM;
+ break;
+ case 2:
+ lp->csum_offload_on_rx_path =
+ XAE_FEATURE_FULL_RX_CSUM;
+ lp->features |= XAE_FEATURE_FULL_RX_CSUM;
+ break;
+ default:
+ lp->csum_offload_on_rx_path = XAE_NO_CSUM_OFFLOAD;
+ }
+ }
+ /* For supporting jumbo frames, the Axi Ethernet hardware must have
+ * a larger Rx/Tx Memory. Typically, the size must be more than or
+ * equal to 16384 bytes, so that we can enable jumbo option and start
+ * supporting jumbo frames. Here we check for memory allocated for
+ * Rx/Tx in the hardware from the device-tree and accordingly set
+ * flags. */
+ p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,rxmem", NULL);
+ if (p) {
+ if ((be32_to_cpup(p)) >= 0x4000)
+ lp->jumbo_support = 1;
+ }
+ p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,temac-type",
+ NULL);
+ if (p)
+ lp->temac_type = be32_to_cpup(p);
+ p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,phy-type", NULL);
+ if (p)
+ lp->phy_type = be32_to_cpup(p);
+
+ /* Find the DMA node, map the DMA registers, and decode the DMA IRQs */
+ np = of_parse_phandle(op->dev.of_node, "axistream-connected", 0);
+ if (!np) {
+ dev_err(&op->dev, "could not find DMA node\n");
+ goto err_iounmap;
+ }
+ lp->dma_regs = of_iomap(np, 0);
+ if (lp->dma_regs) {
+ dev_dbg(&op->dev, "MEM base: %p\n", lp->dma_regs);
+ } else {
+ dev_err(&op->dev, "unable to map DMA registers\n");
+ of_node_put(np);
+ }
+ lp->rx_irq = irq_of_parse_and_map(np, 1);
+ lp->tx_irq = irq_of_parse_and_map(np, 0);
+ of_node_put(np);
+ if ((lp->rx_irq == NO_IRQ) || (lp->tx_irq == NO_IRQ)) {
+ dev_err(&op->dev, "could not determine irqs\n");
+ ret = -ENOMEM;
+ goto err_iounmap_2;
+ }
+
+ /* Retrieve the MAC address */
+ addr = of_get_property(op->dev.of_node, "local-mac-address", &size);
+ if ((!addr) || (size != 6)) {
+ dev_err(&op->dev, "could not find MAC address\n");
+ ret = -ENODEV;
+ goto err_iounmap_2;
+ }
+ axienet_set_mac_address(ndev, (void *) addr);
+
+ lp->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD;
+ lp->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD;
+
+ lp->phy_node = of_parse_phandle(op->dev.of_node, "phy-handle", 0);
+ ret = axienet_mdio_setup(lp, op->dev.of_node);
+ if (ret)
+ dev_warn(&op->dev, "error registering MDIO bus\n");
+
+ ret = register_netdev(lp->ndev);
+ if (ret) {
+ dev_err(lp->dev, "register_netdev() error (%i)\n", ret);
+ goto err_iounmap_2;
+ }
+
+ tasklet_init(&lp->dma_err_tasklet, axienet_dma_err_handler,
+ (unsigned long) lp);
+ tasklet_disable(&lp->dma_err_tasklet);
+
+ return 0;
+
+err_iounmap_2:
+ if (lp->dma_regs)
+ iounmap(lp->dma_regs);
+err_iounmap:
+ iounmap(lp->regs);
+nodev:
+ free_netdev(ndev);
+ ndev = NULL;
+ return ret;
+}
+
+static int __devexit axienet_of_remove(struct platform_device *op)
+{
+ struct net_device *ndev = dev_get_drvdata(&op->dev);
+ struct axienet_local *lp = netdev_priv(ndev);
+
+ axienet_mdio_teardown(lp);
+ unregister_netdev(ndev);
+
+ if (lp->phy_node)
+ of_node_put(lp->phy_node);
+ lp->phy_node = NULL;
+
+ dev_set_drvdata(&op->dev, NULL);
+
+ iounmap(lp->regs);
+ if (lp->dma_regs)
+ iounmap(lp->dma_regs);
+ free_netdev(ndev);
+
+ return 0;
+}
+
+static struct platform_driver axienet_of_driver = {
+ .probe = axienet_of_probe,
+ .remove = __devexit_p(axienet_of_remove),
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "xilinx_axienet",
+ .of_match_table = axienet_of_match,
+ },
+};
+
+static int __init axienet_init(void)
+{
+ return platform_driver_register(&axienet_of_driver);
+}
+
+static void __exit axienet_exit(void)
+{
+ platform_driver_unregister(&axienet_of_driver);
+}
+
+module_init(axienet_init);
+module_exit(axienet_exit);
+
+MODULE_DESCRIPTION("Xilinx Axi Ethernet driver");
+MODULE_AUTHOR("Xilinx");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
new file mode 100644
index 0000000..d70b6e7
--- /dev/null
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
@@ -0,0 +1,238 @@
+/*
+ * MDIO bus driver for the Xilinx Axi Ethernet device
+ *
+ * Copyright (c) 2009 Secret Lab Technologies, Ltd.
+ * Copyright (c) 2010 Xilinx, Inc. All rights reserved.
+ * Copyright (c) 2012 Daniel Borkmann, <daniel.borkmann@tik.ee.ethz.ch>
+ * Copyright (c) 2012 Ariane Keller, <ariane.keller@tik.ee.ethz.ch>
+ */
+
+#include <linux/of_address.h>
+#include <linux/of_mdio.h>
+#include <linux/jiffies.h>
+
+#include "xilinx_axienet.h"
+
+#define MAX_MDIO_FREQ 2500000 /* 2.5 MHz */
+#define DEFAULT_CLOCK_DIVISOR XAE_MDIO_DIV_DFT
+
+/* Wait till MDIO interface is ready to accept a new transaction.*/
+int axienet_mdio_wait_until_ready(struct axienet_local *lp)
+{
+ long end = jiffies + 2;
+ while (!(axienet_ior(lp, XAE_MDIO_MCR_OFFSET) &
+ XAE_MDIO_MCR_READY_MASK)) {
+ if (end - jiffies <= 0) {
+ WARN_ON(1);
+ return -ETIMEDOUT;
+ }
+ udelay(1);
+ }
+ return 0;
+}
+
+/**
+ * axienet_mdio_read - MDIO interface read function
+ * @bus: Pointer to mii bus structure
+ * @phy_id: Address of the PHY device
+ * @reg: PHY register to read
+ *
+ * returns: The register contents on success, -ETIMEDOUT on a timeout
+ *
+ * Reads the contents of the requested register from the requested PHY
+ * address by first writing the details into MCR register. After a while
+ * the register MRD is read to obtain the PHY register content.
+ */
+static int axienet_mdio_read(struct mii_bus *bus, int phy_id, int reg)
+{
+ u32 rc;
+ int ret;
+ struct axienet_local *lp = bus->priv;
+
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+
+ axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
+ (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
+ XAE_MDIO_MCR_PHYAD_MASK) |
+ ((reg << XAE_MDIO_MCR_REGAD_SHIFT) &
+ XAE_MDIO_MCR_REGAD_MASK) |
+ XAE_MDIO_MCR_INITIATE_MASK |
+ XAE_MDIO_MCR_OP_READ_MASK));
+
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+
+ rc = axienet_ior(lp, XAE_MDIO_MRD_OFFSET) & 0x0000FFFF;
+
+ dev_dbg(lp->dev, "axienet_mdio_read(phy_id=%i, reg=%x) == %x\n",
+ phy_id, reg, rc);
+
+ return rc;
+}
+
+/**
+ * axienet_mdio_write - MDIO interface write function
+ * @bus: Pointer to mii bus structure
+ * @phy_id: Address of the PHY device
+ * @reg: PHY register to write to
+ * @val: Value to be written into the register
+ *
+ * returns: 0 on success, -ETIMEDOUT on a timeout
+ *
+ * Writes the value to the requested register by first writing the value
+ * into MWD register. The the MCR register is then appropriately setup
+ * to finish the write operation.
+ */
+static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg,
+ u16 val)
+{
+ int ret;
+ struct axienet_local *lp = bus->priv;
+
+ dev_dbg(lp->dev, "axienet_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
+ phy_id, reg, val);
+
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+
+ axienet_iow(lp, XAE_MDIO_MWD_OFFSET, (u32) val);
+ axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
+ (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
+ XAE_MDIO_MCR_PHYAD_MASK) |
+ ((reg << XAE_MDIO_MCR_REGAD_SHIFT) &
+ XAE_MDIO_MCR_REGAD_MASK) |
+ XAE_MDIO_MCR_INITIATE_MASK |
+ XAE_MDIO_MCR_OP_WRITE_MASK));
+
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+ return 0;
+}
+
+/**
+ * axienet_mdio_setup - MDIO setup function
+ * @lp: Pointer to axienet local data structure.
+ * @np: Pointer to device node
+ *
+ * returns: 0 on success, -ETIMEDOUT on a timeout, -ENOMEM when
+ * mdiobus_alloc (to allocate memory for mii bus structure) fails.
+ *
+ * Sets up the MDIO interface by initializing the MDIO clock and enabling the
+ * MDIO interface in hardware. Register the MDIO interface.
+ **/
+int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np)
+{
+ int ret;
+ u32 clk_div, host_clock;
+ u32 *property_p;
+ struct mii_bus *bus;
+ struct resource res;
+ struct device_node *np1;
+
+ /* clk_div can be calculated by deriving it from the equation:
+ * fMDIO = fHOST / ((1 + clk_div) * 2)
+ *
+ * Where fMDIO <= 2500000, so we get:
+ * fHOST / ((1 + clk_div) * 2) <= 2500000
+ *
+ * Then we get:
+ * 1 / ((1 + clk_div) * 2) <= (2500000 / fHOST)
+ *
+ * Then we get:
+ * 1 / (1 + clk_div) <= ((2500000 * 2) / fHOST)
+ *
+ * Then we get:
+ * 1 / (1 + clk_div) <= (5000000 / fHOST)
+ *
+ * So:
+ * (1 + clk_div) >= (fHOST / 5000000)
+ *
+ * And finally:
+ * clk_div >= (fHOST / 5000000) - 1
+ *
+ * fHOST can be read from the flattened device tree as property
+ * "clock-frequency" from the CPU
+ */
+
+ np1 = of_find_node_by_name(NULL, "cpu");
+ if (!np1) {
+ printk(KERN_WARNING "%s(): Could not find CPU device node.",
+ __func__);
+ printk(KERN_WARNING "Setting MDIO clock divisor to "
+ "default %d\n", DEFAULT_CLOCK_DIVISOR);
+ clk_div = DEFAULT_CLOCK_DIVISOR;
+ goto issue;
+ }
+ property_p = (u32 *) of_get_property(np1, "clock-frequency", NULL);
+ if (!property_p) {
+ printk(KERN_WARNING "%s(): Could not find CPU property: "
+ "clock-frequency.", __func__);
+ printk(KERN_WARNING "Setting MDIO clock divisor to "
+ "default %d\n", DEFAULT_CLOCK_DIVISOR);
+ clk_div = DEFAULT_CLOCK_DIVISOR;
+ goto issue;
+ }
+
+ host_clock = be32_to_cpup(property_p);
+ clk_div = (host_clock / (MAX_MDIO_FREQ * 2)) - 1;
+ /* If there is any remainder from the division of
+ * fHOST / (MAX_MDIO_FREQ * 2), then we need to add
+ * 1 to the clock divisor or we will surely be above 2.5 MHz */
+ if (host_clock % (MAX_MDIO_FREQ * 2))
+ clk_div++;
+
+ printk(KERN_DEBUG "%s(): Setting MDIO clock divisor to %u based "
+ "on %u Hz host clock.\n", __func__, clk_div, host_clock);
+
+ of_node_put(np1);
+issue:
+ axienet_iow(lp, XAE_MDIO_MC_OFFSET,
+ (((u32) clk_div) | XAE_MDIO_MC_MDIOEN_MASK));
+
+ ret = axienet_mdio_wait_until_ready(lp);
+ if (ret < 0)
+ return ret;
+
+ bus = mdiobus_alloc();
+ if (!bus)
+ return -ENOMEM;
+
+ np1 = of_get_parent(lp->phy_node);
+ of_address_to_resource(np1, 0, &res);
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%.8llx",
+ (unsigned long long) res.start);
+
+ bus->priv = lp;
+ bus->name = "Xilinx Axi Ethernet MDIO";
+ bus->read = axienet_mdio_read;
+ bus->write = axienet_mdio_write;
+ bus->parent = lp->dev;
+ bus->irq = lp->mdio_irqs; /* preallocated IRQ table */
+ lp->mii_bus = bus;
+
+ ret = of_mdiobus_register(bus, np1);
+ if (ret) {
+ mdiobus_free(bus);
+ return ret;
+ }
+ return 0;
+}
+
+/**
+ * axienet_mdio_teardown - MDIO remove function
+ * @lp: Pointer to axienet local data structure.
+ *
+ * Unregisters the MDIO and frees any associate memory for mii bus.
+ */
+void axienet_mdio_teardown(struct axienet_local *lp)
+{
+ mdiobus_unregister(lp->mii_bus);
+ kfree(lp->mii_bus->irq);
+ mdiobus_free(lp->mii_bus);
+ lp->mii_bus = NULL;
+}