| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) STMicroelectronics SA 2015 |
| * Authors: Arnaud Pouliquen <arnaud.pouliquen@st.com> |
| * for STMicroelectronics. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/mfd/syscon.h> |
| |
| #include <sound/asoundef.h> |
| #include <sound/soc.h> |
| |
| #include "uniperif.h" |
| |
| /* |
| * Some hardware-related definitions |
| */ |
| |
| /* sys config registers definitions */ |
| #define SYS_CFG_AUDIO_GLUE 0xA4 |
| |
| /* |
| * Driver specific types. |
| */ |
| |
| #define UNIPERIF_PLAYER_CLK_ADJ_MIN -999999 |
| #define UNIPERIF_PLAYER_CLK_ADJ_MAX 1000000 |
| #define UNIPERIF_PLAYER_I2S_OUT 1 /* player id connected to I2S/TDM TX bus */ |
| |
| /* |
| * Note: snd_pcm_hardware is linked to DMA controller but is declared here to |
| * integrate DAI_CPU capability in term of rate and supported channels |
| */ |
| static const struct snd_pcm_hardware uni_player_pcm_hw = { |
| .info = SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER | |
| SNDRV_PCM_INFO_PAUSE | SNDRV_PCM_INFO_MMAP | |
| SNDRV_PCM_INFO_MMAP_VALID, |
| .formats = SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_S16_LE, |
| |
| .rates = SNDRV_PCM_RATE_CONTINUOUS, |
| .rate_min = 8000, |
| .rate_max = 192000, |
| |
| .channels_min = 2, |
| .channels_max = 8, |
| |
| .periods_min = 2, |
| .periods_max = 48, |
| |
| .period_bytes_min = 128, |
| .period_bytes_max = 64 * PAGE_SIZE, |
| .buffer_bytes_max = 256 * PAGE_SIZE |
| }; |
| |
| /* |
| * uni_player_irq_handler |
| * In case of error audio stream is stopped; stop action is protected via PCM |
| * stream lock to avoid race condition with trigger callback. |
| */ |
| static irqreturn_t uni_player_irq_handler(int irq, void *dev_id) |
| { |
| irqreturn_t ret = IRQ_NONE; |
| struct uniperif *player = dev_id; |
| unsigned int status; |
| unsigned int tmp; |
| |
| spin_lock(&player->irq_lock); |
| if (!player->substream) |
| goto irq_spin_unlock; |
| |
| snd_pcm_stream_lock(player->substream); |
| if (player->state == UNIPERIF_STATE_STOPPED) |
| goto stream_unlock; |
| |
| /* Get interrupt status & clear them immediately */ |
| status = GET_UNIPERIF_ITS(player); |
| SET_UNIPERIF_ITS_BCLR(player, status); |
| |
| /* Check for fifo error (underrun) */ |
| if (unlikely(status & UNIPERIF_ITS_FIFO_ERROR_MASK(player))) { |
| dev_err(player->dev, "FIFO underflow error detected\n"); |
| |
| /* Interrupt is just for information when underflow recovery */ |
| if (player->underflow_enabled) { |
| /* Update state to underflow */ |
| player->state = UNIPERIF_STATE_UNDERFLOW; |
| |
| } else { |
| /* Disable interrupt so doesn't continually fire */ |
| SET_UNIPERIF_ITM_BCLR_FIFO_ERROR(player); |
| |
| /* Stop the player */ |
| snd_pcm_stop_xrun(player->substream); |
| } |
| |
| ret = IRQ_HANDLED; |
| } |
| |
| /* Check for dma error (overrun) */ |
| if (unlikely(status & UNIPERIF_ITS_DMA_ERROR_MASK(player))) { |
| dev_err(player->dev, "DMA error detected\n"); |
| |
| /* Disable interrupt so doesn't continually fire */ |
| SET_UNIPERIF_ITM_BCLR_DMA_ERROR(player); |
| |
| /* Stop the player */ |
| snd_pcm_stop_xrun(player->substream); |
| |
| ret = IRQ_HANDLED; |
| } |
| |
| /* Check for underflow recovery done */ |
| if (unlikely(status & UNIPERIF_ITM_UNDERFLOW_REC_DONE_MASK(player))) { |
| if (!player->underflow_enabled) { |
| dev_err(player->dev, |
| "unexpected Underflow recovering\n"); |
| ret = -EPERM; |
| goto stream_unlock; |
| } |
| /* Read the underflow recovery duration */ |
| tmp = GET_UNIPERIF_STATUS_1_UNDERFLOW_DURATION(player); |
| dev_dbg(player->dev, "Underflow recovered (%d LR clocks max)\n", |
| tmp); |
| |
| /* Clear the underflow recovery duration */ |
| SET_UNIPERIF_BIT_CONTROL_CLR_UNDERFLOW_DURATION(player); |
| |
| /* Update state to started */ |
| player->state = UNIPERIF_STATE_STARTED; |
| |
| ret = IRQ_HANDLED; |
| } |
| |
| /* Check if underflow recovery failed */ |
| if (unlikely(status & |
| UNIPERIF_ITM_UNDERFLOW_REC_FAILED_MASK(player))) { |
| dev_err(player->dev, "Underflow recovery failed\n"); |
| |
| /* Stop the player */ |
| snd_pcm_stop_xrun(player->substream); |
| |
| ret = IRQ_HANDLED; |
| } |
| |
| stream_unlock: |
| snd_pcm_stream_unlock(player->substream); |
| irq_spin_unlock: |
| spin_unlock(&player->irq_lock); |
| |
| return ret; |
| } |
| |
| static int uni_player_clk_set_rate(struct uniperif *player, unsigned long rate) |
| { |
| int rate_adjusted, rate_achieved, delta, ret; |
| int adjustment = player->clk_adj; |
| |
| /* |
| * a |
| * F = f + --------- * f = f + d |
| * 1000000 |
| * |
| * a |
| * d = --------- * f |
| * 1000000 |
| * |
| * where: |
| * f - nominal rate |
| * a - adjustment in ppm (parts per milion) |
| * F - rate to be set in synthesizer |
| * d - delta (difference) between f and F |
| */ |
| if (adjustment < 0) { |
| /* div64_64 operates on unsigned values... */ |
| delta = -1; |
| adjustment = -adjustment; |
| } else { |
| delta = 1; |
| } |
| /* 500000 ppm is 0.5, which is used to round up values */ |
| delta *= (int)div64_u64((uint64_t)rate * |
| (uint64_t)adjustment + 500000, 1000000); |
| rate_adjusted = rate + delta; |
| |
| /* Adjusted rate should never be == 0 */ |
| if (!rate_adjusted) |
| return -EINVAL; |
| |
| ret = clk_set_rate(player->clk, rate_adjusted); |
| if (ret < 0) |
| return ret; |
| |
| rate_achieved = clk_get_rate(player->clk); |
| if (!rate_achieved) |
| /* If value is 0 means that clock or parent not valid */ |
| return -EINVAL; |
| |
| /* |
| * Using ALSA's adjustment control, we can modify the rate to be up |
| * to twice as much as requested, but no more |
| */ |
| delta = rate_achieved - rate; |
| if (delta < 0) { |
| /* div64_64 operates on unsigned values... */ |
| delta = -delta; |
| adjustment = -1; |
| } else { |
| adjustment = 1; |
| } |
| /* Frequency/2 is added to round up result */ |
| adjustment *= (int)div64_u64((uint64_t)delta * 1000000 + rate / 2, |
| rate); |
| player->clk_adj = adjustment; |
| return 0; |
| } |
| |
| static void uni_player_set_channel_status(struct uniperif *player, |
| struct snd_pcm_runtime *runtime) |
| { |
| int n; |
| unsigned int status; |
| |
| /* |
| * Some AVRs and TVs require the channel status to contain a correct |
| * sampling frequency. If no sample rate is already specified, then |
| * set one. |
| */ |
| mutex_lock(&player->ctrl_lock); |
| if (runtime) { |
| switch (runtime->rate) { |
| case 22050: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_22050; |
| break; |
| case 44100: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_44100; |
| break; |
| case 88200: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_88200; |
| break; |
| case 176400: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_176400; |
| break; |
| case 24000: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_24000; |
| break; |
| case 48000: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_48000; |
| break; |
| case 96000: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_96000; |
| break; |
| case 192000: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_192000; |
| break; |
| case 32000: |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_32000; |
| break; |
| default: |
| /* Mark as sampling frequency not indicated */ |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_NOTID; |
| break; |
| } |
| } |
| |
| /* Audio mode: |
| * Use audio mode status to select PCM or encoded mode |
| */ |
| if (player->stream_settings.iec958.status[0] & IEC958_AES0_NONAUDIO) |
| player->stream_settings.encoding_mode = |
| UNIPERIF_IEC958_ENCODING_MODE_ENCODED; |
| else |
| player->stream_settings.encoding_mode = |
| UNIPERIF_IEC958_ENCODING_MODE_PCM; |
| |
| if (player->stream_settings.encoding_mode == |
| UNIPERIF_IEC958_ENCODING_MODE_PCM) |
| /* Clear user validity bits */ |
| SET_UNIPERIF_USER_VALIDITY_VALIDITY_LR(player, 0); |
| else |
| /* Set user validity bits */ |
| SET_UNIPERIF_USER_VALIDITY_VALIDITY_LR(player, 1); |
| |
| /* Program the new channel status */ |
| for (n = 0; n < 6; ++n) { |
| status = |
| player->stream_settings.iec958.status[0 + (n * 4)] & 0xf; |
| status |= |
| player->stream_settings.iec958.status[1 + (n * 4)] << 8; |
| status |= |
| player->stream_settings.iec958.status[2 + (n * 4)] << 16; |
| status |= |
| player->stream_settings.iec958.status[3 + (n * 4)] << 24; |
| SET_UNIPERIF_CHANNEL_STA_REGN(player, n, status); |
| } |
| mutex_unlock(&player->ctrl_lock); |
| |
| /* Update the channel status */ |
| if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0) |
| SET_UNIPERIF_CONFIG_CHL_STS_UPDATE(player); |
| else |
| SET_UNIPERIF_BIT_CONTROL_CHL_STS_UPDATE(player); |
| } |
| |
| static int uni_player_prepare_iec958(struct uniperif *player, |
| struct snd_pcm_runtime *runtime) |
| { |
| int clk_div; |
| |
| clk_div = player->mclk / runtime->rate; |
| |
| /* Oversampling must be multiple of 128 as iec958 frame is 32-bits */ |
| if ((clk_div % 128) || (clk_div <= 0)) { |
| dev_err(player->dev, "%s: invalid clk_div %d\n", |
| __func__, clk_div); |
| return -EINVAL; |
| } |
| |
| switch (runtime->format) { |
| case SNDRV_PCM_FORMAT_S16_LE: |
| /* 16/16 memory format */ |
| SET_UNIPERIF_CONFIG_MEM_FMT_16_16(player); |
| /* 16-bits per sub-frame */ |
| SET_UNIPERIF_I2S_FMT_NBIT_32(player); |
| /* Set 16-bit sample precision */ |
| SET_UNIPERIF_I2S_FMT_DATA_SIZE_16(player); |
| break; |
| case SNDRV_PCM_FORMAT_S32_LE: |
| /* 16/0 memory format */ |
| SET_UNIPERIF_CONFIG_MEM_FMT_16_0(player); |
| /* 32-bits per sub-frame */ |
| SET_UNIPERIF_I2S_FMT_NBIT_32(player); |
| /* Set 24-bit sample precision */ |
| SET_UNIPERIF_I2S_FMT_DATA_SIZE_24(player); |
| break; |
| default: |
| dev_err(player->dev, "format not supported\n"); |
| return -EINVAL; |
| } |
| |
| /* Set parity to be calculated by the hardware */ |
| SET_UNIPERIF_CONFIG_PARITY_CNTR_BY_HW(player); |
| |
| /* Set channel status bits to be inserted by the hardware */ |
| SET_UNIPERIF_CONFIG_CHANNEL_STA_CNTR_BY_HW(player); |
| |
| /* Set user data bits to be inserted by the hardware */ |
| SET_UNIPERIF_CONFIG_USER_DAT_CNTR_BY_HW(player); |
| |
| /* Set validity bits to be inserted by the hardware */ |
| SET_UNIPERIF_CONFIG_VALIDITY_DAT_CNTR_BY_HW(player); |
| |
| /* Set full software control to disabled */ |
| SET_UNIPERIF_CONFIG_SPDIF_SW_CTRL_DISABLE(player); |
| |
| SET_UNIPERIF_CTRL_ZERO_STUFF_HW(player); |
| |
| /* Update the channel status */ |
| uni_player_set_channel_status(player, runtime); |
| |
| /* Clear the user validity user bits */ |
| SET_UNIPERIF_USER_VALIDITY_VALIDITY_LR(player, 0); |
| |
| /* Disable one-bit audio mode */ |
| SET_UNIPERIF_CONFIG_ONE_BIT_AUD_DISABLE(player); |
| |
| /* Enable consecutive frames repetition of Z preamble (not for HBRA) */ |
| SET_UNIPERIF_CONFIG_REPEAT_CHL_STS_ENABLE(player); |
| |
| /* Change to SUF0_SUBF1 and left/right channels swap! */ |
| SET_UNIPERIF_CONFIG_SUBFRAME_SEL_SUBF1_SUBF0(player); |
| |
| /* Set data output as MSB first */ |
| SET_UNIPERIF_I2S_FMT_ORDER_MSB(player); |
| |
| if (player->stream_settings.encoding_mode == |
| UNIPERIF_IEC958_ENCODING_MODE_ENCODED) |
| SET_UNIPERIF_CTRL_EXIT_STBY_ON_EOBLOCK_ON(player); |
| else |
| SET_UNIPERIF_CTRL_EXIT_STBY_ON_EOBLOCK_OFF(player); |
| |
| SET_UNIPERIF_I2S_FMT_NUM_CH(player, runtime->channels / 2); |
| |
| /* Set rounding to off */ |
| SET_UNIPERIF_CTRL_ROUNDING_OFF(player); |
| |
| /* Set clock divisor */ |
| SET_UNIPERIF_CTRL_DIVIDER(player, clk_div / 128); |
| |
| /* Set the spdif latency to not wait before starting player */ |
| SET_UNIPERIF_CTRL_SPDIF_LAT_OFF(player); |
| |
| /* |
| * Ensure iec958 formatting is off. It will be enabled in function |
| * uni_player_start() at the same time as the operation |
| * mode is set to work around a silicon issue. |
| */ |
| if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0) |
| SET_UNIPERIF_CTRL_SPDIF_FMT_OFF(player); |
| else |
| SET_UNIPERIF_CTRL_SPDIF_FMT_ON(player); |
| |
| return 0; |
| } |
| |
| static int uni_player_prepare_pcm(struct uniperif *player, |
| struct snd_pcm_runtime *runtime) |
| { |
| int output_frame_size, slot_width, clk_div; |
| |
| /* Force slot width to 32 in I2S mode (HW constraint) */ |
| if ((player->daifmt & SND_SOC_DAIFMT_FORMAT_MASK) == |
| SND_SOC_DAIFMT_I2S) |
| slot_width = 32; |
| else |
| slot_width = snd_pcm_format_width(runtime->format); |
| |
| output_frame_size = slot_width * runtime->channels; |
| |
| clk_div = player->mclk / runtime->rate; |
| /* |
| * For 32 bits subframe clk_div must be a multiple of 128, |
| * for 16 bits must be a multiple of 64 |
| */ |
| if ((slot_width == 32) && (clk_div % 128)) { |
| dev_err(player->dev, "%s: invalid clk_div\n", __func__); |
| return -EINVAL; |
| } |
| |
| if ((slot_width == 16) && (clk_div % 64)) { |
| dev_err(player->dev, "%s: invalid clk_div\n", __func__); |
| return -EINVAL; |
| } |
| |
| /* |
| * Number of bits per subframe (which is one channel sample) |
| * on output - Transfer 16 or 32 bits from FIFO |
| */ |
| switch (slot_width) { |
| case 32: |
| SET_UNIPERIF_I2S_FMT_NBIT_32(player); |
| SET_UNIPERIF_I2S_FMT_DATA_SIZE_32(player); |
| break; |
| case 16: |
| SET_UNIPERIF_I2S_FMT_NBIT_16(player); |
| SET_UNIPERIF_I2S_FMT_DATA_SIZE_16(player); |
| break; |
| default: |
| dev_err(player->dev, "subframe format not supported\n"); |
| return -EINVAL; |
| } |
| |
| /* Configure data memory format */ |
| switch (runtime->format) { |
| case SNDRV_PCM_FORMAT_S16_LE: |
| /* One data word contains two samples */ |
| SET_UNIPERIF_CONFIG_MEM_FMT_16_16(player); |
| break; |
| |
| case SNDRV_PCM_FORMAT_S32_LE: |
| /* |
| * Actually "16 bits/0 bits" means "32/28/24/20/18/16 bits |
| * on the left than zeros (if less than 32 bytes)"... ;-) |
| */ |
| SET_UNIPERIF_CONFIG_MEM_FMT_16_0(player); |
| break; |
| |
| default: |
| dev_err(player->dev, "format not supported\n"); |
| return -EINVAL; |
| } |
| |
| /* Set rounding to off */ |
| SET_UNIPERIF_CTRL_ROUNDING_OFF(player); |
| |
| /* Set clock divisor */ |
| SET_UNIPERIF_CTRL_DIVIDER(player, clk_div / (2 * output_frame_size)); |
| |
| /* Number of channelsmust be even*/ |
| if ((runtime->channels % 2) || (runtime->channels < 2) || |
| (runtime->channels > 10)) { |
| dev_err(player->dev, "%s: invalid nb of channels\n", __func__); |
| return -EINVAL; |
| } |
| |
| SET_UNIPERIF_I2S_FMT_NUM_CH(player, runtime->channels / 2); |
| |
| /* Set 1-bit audio format to disabled */ |
| SET_UNIPERIF_CONFIG_ONE_BIT_AUD_DISABLE(player); |
| |
| SET_UNIPERIF_I2S_FMT_ORDER_MSB(player); |
| |
| /* No iec958 formatting as outputting to DAC */ |
| SET_UNIPERIF_CTRL_SPDIF_FMT_OFF(player); |
| |
| return 0; |
| } |
| |
| static int uni_player_prepare_tdm(struct uniperif *player, |
| struct snd_pcm_runtime *runtime) |
| { |
| int tdm_frame_size; /* unip tdm frame size in bytes */ |
| int user_frame_size; /* user tdm frame size in bytes */ |
| /* default unip TDM_WORD_POS_X_Y */ |
| unsigned int word_pos[4] = { |
| 0x04060002, 0x0C0E080A, 0x14161012, 0x1C1E181A}; |
| int freq, ret; |
| |
| tdm_frame_size = |
| sti_uniperiph_get_unip_tdm_frame_size(player); |
| user_frame_size = |
| sti_uniperiph_get_user_frame_size(runtime); |
| |
| /* fix 16/0 format */ |
| SET_UNIPERIF_CONFIG_MEM_FMT_16_0(player); |
| SET_UNIPERIF_I2S_FMT_DATA_SIZE_32(player); |
| |
| /* number of words inserted on the TDM line */ |
| SET_UNIPERIF_I2S_FMT_NUM_CH(player, user_frame_size / 4 / 2); |
| |
| SET_UNIPERIF_I2S_FMT_ORDER_MSB(player); |
| SET_UNIPERIF_I2S_FMT_ALIGN_LEFT(player); |
| |
| /* Enable the tdm functionality */ |
| SET_UNIPERIF_TDM_ENABLE_TDM_ENABLE(player); |
| |
| /* number of 8 bits timeslots avail in unip tdm frame */ |
| SET_UNIPERIF_TDM_FS_REF_DIV_NUM_TIMESLOT(player, tdm_frame_size); |
| |
| /* set the timeslot allocation for words in FIFO */ |
| sti_uniperiph_get_tdm_word_pos(player, word_pos); |
| SET_UNIPERIF_TDM_WORD_POS(player, 1_2, word_pos[WORD_1_2]); |
| SET_UNIPERIF_TDM_WORD_POS(player, 3_4, word_pos[WORD_3_4]); |
| SET_UNIPERIF_TDM_WORD_POS(player, 5_6, word_pos[WORD_5_6]); |
| SET_UNIPERIF_TDM_WORD_POS(player, 7_8, word_pos[WORD_7_8]); |
| |
| /* set unip clk rate (not done vai set_sysclk ops) */ |
| freq = runtime->rate * tdm_frame_size * 8; |
| mutex_lock(&player->ctrl_lock); |
| ret = uni_player_clk_set_rate(player, freq); |
| if (!ret) |
| player->mclk = freq; |
| mutex_unlock(&player->ctrl_lock); |
| |
| return 0; |
| } |
| |
| /* |
| * ALSA uniperipheral iec958 controls |
| */ |
| static int uni_player_ctl_iec958_info(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_info *uinfo) |
| { |
| uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958; |
| uinfo->count = 1; |
| |
| return 0; |
| } |
| |
| static int uni_player_ctl_iec958_get(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_value *ucontrol) |
| { |
| struct snd_soc_dai *dai = snd_kcontrol_chip(kcontrol); |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| struct snd_aes_iec958 *iec958 = &player->stream_settings.iec958; |
| |
| mutex_lock(&player->ctrl_lock); |
| ucontrol->value.iec958.status[0] = iec958->status[0]; |
| ucontrol->value.iec958.status[1] = iec958->status[1]; |
| ucontrol->value.iec958.status[2] = iec958->status[2]; |
| ucontrol->value.iec958.status[3] = iec958->status[3]; |
| mutex_unlock(&player->ctrl_lock); |
| return 0; |
| } |
| |
| static int uni_player_ctl_iec958_put(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_value *ucontrol) |
| { |
| struct snd_soc_dai *dai = snd_kcontrol_chip(kcontrol); |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| struct snd_aes_iec958 *iec958 = &player->stream_settings.iec958; |
| unsigned long flags; |
| |
| mutex_lock(&player->ctrl_lock); |
| iec958->status[0] = ucontrol->value.iec958.status[0]; |
| iec958->status[1] = ucontrol->value.iec958.status[1]; |
| iec958->status[2] = ucontrol->value.iec958.status[2]; |
| iec958->status[3] = ucontrol->value.iec958.status[3]; |
| mutex_unlock(&player->ctrl_lock); |
| |
| spin_lock_irqsave(&player->irq_lock, flags); |
| if (player->substream && player->substream->runtime) |
| uni_player_set_channel_status(player, |
| player->substream->runtime); |
| else |
| uni_player_set_channel_status(player, NULL); |
| |
| spin_unlock_irqrestore(&player->irq_lock, flags); |
| return 0; |
| } |
| |
| static struct snd_kcontrol_new uni_player_iec958_ctl = { |
| .iface = SNDRV_CTL_ELEM_IFACE_PCM, |
| .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, DEFAULT), |
| .info = uni_player_ctl_iec958_info, |
| .get = uni_player_ctl_iec958_get, |
| .put = uni_player_ctl_iec958_put, |
| }; |
| |
| /* |
| * uniperif rate adjustement control |
| */ |
| static int snd_sti_clk_adjustment_info(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_info *uinfo) |
| { |
| uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; |
| uinfo->count = 1; |
| uinfo->value.integer.min = UNIPERIF_PLAYER_CLK_ADJ_MIN; |
| uinfo->value.integer.max = UNIPERIF_PLAYER_CLK_ADJ_MAX; |
| uinfo->value.integer.step = 1; |
| |
| return 0; |
| } |
| |
| static int snd_sti_clk_adjustment_get(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_value *ucontrol) |
| { |
| struct snd_soc_dai *dai = snd_kcontrol_chip(kcontrol); |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| |
| mutex_lock(&player->ctrl_lock); |
| ucontrol->value.integer.value[0] = player->clk_adj; |
| mutex_unlock(&player->ctrl_lock); |
| |
| return 0; |
| } |
| |
| static int snd_sti_clk_adjustment_put(struct snd_kcontrol *kcontrol, |
| struct snd_ctl_elem_value *ucontrol) |
| { |
| struct snd_soc_dai *dai = snd_kcontrol_chip(kcontrol); |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| int ret = 0; |
| |
| if ((ucontrol->value.integer.value[0] < UNIPERIF_PLAYER_CLK_ADJ_MIN) || |
| (ucontrol->value.integer.value[0] > UNIPERIF_PLAYER_CLK_ADJ_MAX)) |
| return -EINVAL; |
| |
| mutex_lock(&player->ctrl_lock); |
| player->clk_adj = ucontrol->value.integer.value[0]; |
| |
| if (player->mclk) |
| ret = uni_player_clk_set_rate(player, player->mclk); |
| mutex_unlock(&player->ctrl_lock); |
| |
| return ret; |
| } |
| |
| static struct snd_kcontrol_new uni_player_clk_adj_ctl = { |
| .iface = SNDRV_CTL_ELEM_IFACE_PCM, |
| .name = "PCM Playback Oversampling Freq. Adjustment", |
| .info = snd_sti_clk_adjustment_info, |
| .get = snd_sti_clk_adjustment_get, |
| .put = snd_sti_clk_adjustment_put, |
| }; |
| |
| static struct snd_kcontrol_new *snd_sti_pcm_ctl[] = { |
| &uni_player_clk_adj_ctl, |
| }; |
| |
| static struct snd_kcontrol_new *snd_sti_iec_ctl[] = { |
| &uni_player_iec958_ctl, |
| &uni_player_clk_adj_ctl, |
| }; |
| |
| static int uni_player_startup(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&player->irq_lock, flags); |
| player->substream = substream; |
| spin_unlock_irqrestore(&player->irq_lock, flags); |
| |
| player->clk_adj = 0; |
| |
| if (!UNIPERIF_TYPE_IS_TDM(player)) |
| return 0; |
| |
| /* refine hw constraint in tdm mode */ |
| ret = snd_pcm_hw_rule_add(substream->runtime, 0, |
| SNDRV_PCM_HW_PARAM_CHANNELS, |
| sti_uniperiph_fix_tdm_chan, |
| player, SNDRV_PCM_HW_PARAM_CHANNELS, |
| -1); |
| if (ret < 0) |
| return ret; |
| |
| return snd_pcm_hw_rule_add(substream->runtime, 0, |
| SNDRV_PCM_HW_PARAM_FORMAT, |
| sti_uniperiph_fix_tdm_format, |
| player, SNDRV_PCM_HW_PARAM_FORMAT, |
| -1); |
| } |
| |
| static int uni_player_set_sysclk(struct snd_soc_dai *dai, int clk_id, |
| unsigned int freq, int dir) |
| { |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| int ret; |
| |
| if (UNIPERIF_TYPE_IS_TDM(player) || (dir == SND_SOC_CLOCK_IN)) |
| return 0; |
| |
| if (clk_id != 0) |
| return -EINVAL; |
| |
| mutex_lock(&player->ctrl_lock); |
| ret = uni_player_clk_set_rate(player, freq); |
| if (!ret) |
| player->mclk = freq; |
| mutex_unlock(&player->ctrl_lock); |
| |
| return ret; |
| } |
| |
| static int uni_player_prepare(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| struct snd_pcm_runtime *runtime = substream->runtime; |
| int transfer_size, trigger_limit; |
| int ret; |
| |
| /* The player should be stopped */ |
| if (player->state != UNIPERIF_STATE_STOPPED) { |
| dev_err(player->dev, "%s: invalid player state %d\n", __func__, |
| player->state); |
| return -EINVAL; |
| } |
| |
| /* Calculate transfer size (in fifo cells and bytes) for frame count */ |
| if (player->type == SND_ST_UNIPERIF_TYPE_TDM) { |
| /* transfer size = user frame size (in 32 bits FIFO cell) */ |
| transfer_size = |
| sti_uniperiph_get_user_frame_size(runtime) / 4; |
| } else { |
| transfer_size = runtime->channels * UNIPERIF_FIFO_FRAMES; |
| } |
| |
| /* Calculate number of empty cells available before asserting DREQ */ |
| if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0) { |
| trigger_limit = UNIPERIF_FIFO_SIZE - transfer_size; |
| } else { |
| /* |
| * Since SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0 |
| * FDMA_TRIGGER_LIMIT also controls when the state switches |
| * from OFF or STANDBY to AUDIO DATA. |
| */ |
| trigger_limit = transfer_size; |
| } |
| |
| /* Trigger limit must be an even number */ |
| if ((!trigger_limit % 2) || (trigger_limit != 1 && transfer_size % 2) || |
| (trigger_limit > UNIPERIF_CONFIG_DMA_TRIG_LIMIT_MASK(player))) { |
| dev_err(player->dev, "invalid trigger limit %d\n", |
| trigger_limit); |
| return -EINVAL; |
| } |
| |
| SET_UNIPERIF_CONFIG_DMA_TRIG_LIMIT(player, trigger_limit); |
| |
| /* Uniperipheral setup depends on player type */ |
| switch (player->type) { |
| case SND_ST_UNIPERIF_TYPE_HDMI: |
| ret = uni_player_prepare_iec958(player, runtime); |
| break; |
| case SND_ST_UNIPERIF_TYPE_PCM: |
| ret = uni_player_prepare_pcm(player, runtime); |
| break; |
| case SND_ST_UNIPERIF_TYPE_SPDIF: |
| ret = uni_player_prepare_iec958(player, runtime); |
| break; |
| case SND_ST_UNIPERIF_TYPE_TDM: |
| ret = uni_player_prepare_tdm(player, runtime); |
| break; |
| default: |
| dev_err(player->dev, "invalid player type\n"); |
| return -EINVAL; |
| } |
| |
| if (ret) |
| return ret; |
| |
| switch (player->daifmt & SND_SOC_DAIFMT_INV_MASK) { |
| case SND_SOC_DAIFMT_NB_NF: |
| SET_UNIPERIF_I2S_FMT_LR_POL_LOW(player); |
| SET_UNIPERIF_I2S_FMT_SCLK_EDGE_RISING(player); |
| break; |
| case SND_SOC_DAIFMT_NB_IF: |
| SET_UNIPERIF_I2S_FMT_LR_POL_HIG(player); |
| SET_UNIPERIF_I2S_FMT_SCLK_EDGE_RISING(player); |
| break; |
| case SND_SOC_DAIFMT_IB_NF: |
| SET_UNIPERIF_I2S_FMT_LR_POL_LOW(player); |
| SET_UNIPERIF_I2S_FMT_SCLK_EDGE_FALLING(player); |
| break; |
| case SND_SOC_DAIFMT_IB_IF: |
| SET_UNIPERIF_I2S_FMT_LR_POL_HIG(player); |
| SET_UNIPERIF_I2S_FMT_SCLK_EDGE_FALLING(player); |
| break; |
| } |
| |
| switch (player->daifmt & SND_SOC_DAIFMT_FORMAT_MASK) { |
| case SND_SOC_DAIFMT_I2S: |
| SET_UNIPERIF_I2S_FMT_ALIGN_LEFT(player); |
| SET_UNIPERIF_I2S_FMT_PADDING_I2S_MODE(player); |
| break; |
| case SND_SOC_DAIFMT_LEFT_J: |
| SET_UNIPERIF_I2S_FMT_ALIGN_LEFT(player); |
| SET_UNIPERIF_I2S_FMT_PADDING_SONY_MODE(player); |
| break; |
| case SND_SOC_DAIFMT_RIGHT_J: |
| SET_UNIPERIF_I2S_FMT_ALIGN_RIGHT(player); |
| SET_UNIPERIF_I2S_FMT_PADDING_SONY_MODE(player); |
| break; |
| default: |
| dev_err(player->dev, "format not supported\n"); |
| return -EINVAL; |
| } |
| |
| SET_UNIPERIF_I2S_FMT_NO_OF_SAMPLES_TO_READ(player, 0); |
| |
| |
| return sti_uniperiph_reset(player); |
| } |
| |
| static int uni_player_start(struct uniperif *player) |
| { |
| int ret; |
| |
| /* The player should be stopped */ |
| if (player->state != UNIPERIF_STATE_STOPPED) { |
| dev_err(player->dev, "%s: invalid player state\n", __func__); |
| return -EINVAL; |
| } |
| |
| ret = clk_prepare_enable(player->clk); |
| if (ret) { |
| dev_err(player->dev, "%s: Failed to enable clock\n", __func__); |
| return ret; |
| } |
| |
| /* Clear any pending interrupts */ |
| SET_UNIPERIF_ITS_BCLR(player, GET_UNIPERIF_ITS(player)); |
| |
| /* Set the interrupt mask */ |
| SET_UNIPERIF_ITM_BSET_DMA_ERROR(player); |
| SET_UNIPERIF_ITM_BSET_FIFO_ERROR(player); |
| |
| /* Enable underflow recovery interrupts */ |
| if (player->underflow_enabled) { |
| SET_UNIPERIF_ITM_BSET_UNDERFLOW_REC_DONE(player); |
| SET_UNIPERIF_ITM_BSET_UNDERFLOW_REC_FAILED(player); |
| } |
| |
| ret = sti_uniperiph_reset(player); |
| if (ret < 0) { |
| clk_disable_unprepare(player->clk); |
| return ret; |
| } |
| |
| /* |
| * Does not use IEC61937 features of the uniperipheral hardware. |
| * Instead it performs IEC61937 in software and inserts it directly |
| * into the audio data stream. As such, when encoded mode is selected, |
| * linear pcm mode is still used, but with the differences of the |
| * channel status bits set for encoded mode and the validity bits set. |
| */ |
| SET_UNIPERIF_CTRL_OPERATION_PCM_DATA(player); |
| |
| /* |
| * If iec958 formatting is required for hdmi or spdif, then it must be |
| * enabled after the operation mode is set. If set prior to this, it |
| * will not take affect and hang the player. |
| */ |
| if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0) |
| if (UNIPERIF_TYPE_IS_IEC958(player)) |
| SET_UNIPERIF_CTRL_SPDIF_FMT_ON(player); |
| |
| /* Force channel status update (no update if clk disable) */ |
| if (player->ver < SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0) |
| SET_UNIPERIF_CONFIG_CHL_STS_UPDATE(player); |
| else |
| SET_UNIPERIF_BIT_CONTROL_CHL_STS_UPDATE(player); |
| |
| /* Update state to started */ |
| player->state = UNIPERIF_STATE_STARTED; |
| |
| return 0; |
| } |
| |
| static int uni_player_stop(struct uniperif *player) |
| { |
| int ret; |
| |
| /* The player should not be in stopped state */ |
| if (player->state == UNIPERIF_STATE_STOPPED) { |
| dev_err(player->dev, "%s: invalid player state\n", __func__); |
| return -EINVAL; |
| } |
| |
| /* Turn the player off */ |
| SET_UNIPERIF_CTRL_OPERATION_OFF(player); |
| |
| ret = sti_uniperiph_reset(player); |
| if (ret < 0) |
| return ret; |
| |
| /* Disable interrupts */ |
| SET_UNIPERIF_ITM_BCLR(player, GET_UNIPERIF_ITM(player)); |
| |
| /* Disable clock */ |
| clk_disable_unprepare(player->clk); |
| |
| /* Update state to stopped and return */ |
| player->state = UNIPERIF_STATE_STOPPED; |
| |
| return 0; |
| } |
| |
| int uni_player_resume(struct uniperif *player) |
| { |
| int ret; |
| |
| /* Select the frequency synthesizer clock */ |
| if (player->clk_sel) { |
| ret = regmap_field_write(player->clk_sel, 1); |
| if (ret) { |
| dev_err(player->dev, |
| "%s: Failed to select freq synth clock\n", |
| __func__); |
| return ret; |
| } |
| } |
| |
| SET_UNIPERIF_CONFIG_BACK_STALL_REQ_DISABLE(player); |
| SET_UNIPERIF_CTRL_ROUNDING_OFF(player); |
| SET_UNIPERIF_CTRL_SPDIF_LAT_OFF(player); |
| SET_UNIPERIF_CONFIG_IDLE_MOD_DISABLE(player); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(uni_player_resume); |
| |
| static int uni_player_trigger(struct snd_pcm_substream *substream, |
| int cmd, struct snd_soc_dai *dai) |
| { |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| |
| switch (cmd) { |
| case SNDRV_PCM_TRIGGER_START: |
| return uni_player_start(player); |
| case SNDRV_PCM_TRIGGER_STOP: |
| return uni_player_stop(player); |
| case SNDRV_PCM_TRIGGER_RESUME: |
| return uni_player_resume(player); |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static void uni_player_shutdown(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *dai) |
| { |
| struct sti_uniperiph_data *priv = snd_soc_dai_get_drvdata(dai); |
| struct uniperif *player = priv->dai_data.uni; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&player->irq_lock, flags); |
| if (player->state != UNIPERIF_STATE_STOPPED) |
| /* Stop the player */ |
| uni_player_stop(player); |
| |
| player->substream = NULL; |
| spin_unlock_irqrestore(&player->irq_lock, flags); |
| } |
| |
| static int uni_player_parse_dt_audio_glue(struct platform_device *pdev, |
| struct uniperif *player) |
| { |
| struct device_node *node = pdev->dev.of_node; |
| struct regmap *regmap; |
| struct reg_field regfield[2] = { |
| /* PCM_CLK_SEL */ |
| REG_FIELD(SYS_CFG_AUDIO_GLUE, |
| 8 + player->id, |
| 8 + player->id), |
| /* PCMP_VALID_SEL */ |
| REG_FIELD(SYS_CFG_AUDIO_GLUE, 0, 1) |
| }; |
| |
| regmap = syscon_regmap_lookup_by_phandle(node, "st,syscfg"); |
| |
| if (IS_ERR(regmap)) { |
| dev_err(&pdev->dev, "sti-audio-clk-glue syscf not found\n"); |
| return PTR_ERR(regmap); |
| } |
| |
| player->clk_sel = regmap_field_alloc(regmap, regfield[0]); |
| player->valid_sel = regmap_field_alloc(regmap, regfield[1]); |
| |
| return 0; |
| } |
| |
| static const struct snd_soc_dai_ops uni_player_dai_ops = { |
| .startup = uni_player_startup, |
| .shutdown = uni_player_shutdown, |
| .prepare = uni_player_prepare, |
| .trigger = uni_player_trigger, |
| .hw_params = sti_uniperiph_dai_hw_params, |
| .set_fmt = sti_uniperiph_dai_set_fmt, |
| .set_sysclk = uni_player_set_sysclk, |
| .set_tdm_slot = sti_uniperiph_set_tdm_slot |
| }; |
| |
| int uni_player_init(struct platform_device *pdev, |
| struct uniperif *player) |
| { |
| int ret = 0; |
| |
| player->dev = &pdev->dev; |
| player->state = UNIPERIF_STATE_STOPPED; |
| player->dai_ops = &uni_player_dai_ops; |
| |
| /* Get PCM_CLK_SEL & PCMP_VALID_SEL from audio-glue-ctrl SoC reg */ |
| ret = uni_player_parse_dt_audio_glue(pdev, player); |
| |
| if (ret < 0) { |
| dev_err(player->dev, "Failed to parse DeviceTree\n"); |
| return ret; |
| } |
| |
| /* Underflow recovery is only supported on later ip revisions */ |
| if (player->ver >= SND_ST_UNIPERIF_VERSION_UNI_PLR_TOP_1_0) |
| player->underflow_enabled = 1; |
| |
| if (UNIPERIF_TYPE_IS_TDM(player)) |
| player->hw = &uni_tdm_hw; |
| else |
| player->hw = &uni_player_pcm_hw; |
| |
| /* Get uniperif resource */ |
| player->clk = of_clk_get(pdev->dev.of_node, 0); |
| if (IS_ERR(player->clk)) { |
| dev_err(player->dev, "Failed to get clock\n"); |
| return PTR_ERR(player->clk); |
| } |
| |
| /* Select the frequency synthesizer clock */ |
| if (player->clk_sel) { |
| ret = regmap_field_write(player->clk_sel, 1); |
| if (ret) { |
| dev_err(player->dev, |
| "%s: Failed to select freq synth clock\n", |
| __func__); |
| return ret; |
| } |
| } |
| |
| /* connect to I2S/TDM TX bus */ |
| if (player->valid_sel && |
| (player->id == UNIPERIF_PLAYER_I2S_OUT)) { |
| ret = regmap_field_write(player->valid_sel, player->id); |
| if (ret) { |
| dev_err(player->dev, |
| "%s: unable to connect to tdm bus\n", __func__); |
| return ret; |
| } |
| } |
| |
| ret = devm_request_irq(&pdev->dev, player->irq, |
| uni_player_irq_handler, IRQF_SHARED, |
| dev_name(&pdev->dev), player); |
| if (ret < 0) { |
| dev_err(player->dev, "unable to request IRQ %d\n", player->irq); |
| return ret; |
| } |
| |
| mutex_init(&player->ctrl_lock); |
| spin_lock_init(&player->irq_lock); |
| |
| /* Ensure that disabled by default */ |
| SET_UNIPERIF_CONFIG_BACK_STALL_REQ_DISABLE(player); |
| SET_UNIPERIF_CTRL_ROUNDING_OFF(player); |
| SET_UNIPERIF_CTRL_SPDIF_LAT_OFF(player); |
| SET_UNIPERIF_CONFIG_IDLE_MOD_DISABLE(player); |
| |
| if (UNIPERIF_TYPE_IS_IEC958(player)) { |
| /* Set default iec958 status bits */ |
| |
| /* Consumer, PCM, copyright, 2ch, mode 0 */ |
| player->stream_settings.iec958.status[0] = 0x00; |
| /* Broadcast reception category */ |
| player->stream_settings.iec958.status[1] = |
| IEC958_AES1_CON_GENERAL; |
| /* Do not take into account source or channel number */ |
| player->stream_settings.iec958.status[2] = |
| IEC958_AES2_CON_SOURCE_UNSPEC; |
| /* Sampling frequency not indicated */ |
| player->stream_settings.iec958.status[3] = |
| IEC958_AES3_CON_FS_NOTID; |
| /* Max sample word 24-bit, sample word length not indicated */ |
| player->stream_settings.iec958.status[4] = |
| IEC958_AES4_CON_MAX_WORDLEN_24 | |
| IEC958_AES4_CON_WORDLEN_24_20; |
| |
| player->num_ctrls = ARRAY_SIZE(snd_sti_iec_ctl); |
| player->snd_ctrls = snd_sti_iec_ctl[0]; |
| } else { |
| player->num_ctrls = ARRAY_SIZE(snd_sti_pcm_ctl); |
| player->snd_ctrls = snd_sti_pcm_ctl[0]; |
| } |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(uni_player_init); |