ARM: DT: apq8064: Add i2c device nodes
This patch adds i2c pinctrl DT node for IFC6410 board. It also adds
necessary DT support for i2c eeprom which is present on IFC6410.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index 27c7dfe..b396c83 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -5,6 +5,33 @@
compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
soc {
+ pinctrl@800000 {
+ i2c1_pins: i2c1 {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "gsbi1";
+ };
+ };
+ };
+
+ gsbi@12440000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+
+ i2c@12460000 {
+ status = "okay";
+ clock-frequency = <200000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "default";
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <32>;
+ };
+ };
+ };
+
gsbi@16600000 {
status = "ok";
qcom,mode = <GSBI_PROT_I2C_UART>;
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index f31d20b..b3154c0 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -163,6 +163,48 @@
regulator;
};
+ gsbi1: gsbi@12440000 {
+ status = "disabled";
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x12440000 0x100>;
+ clocks = <&gcc GSBI1_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ i2c1: i2c@12460000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x12460000 0x1000>;
+ interrupts = <0 194 IRQ_TYPE_NONE>;
+ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ gsbi2: gsbi@12480000 {
+ status = "disabled";
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x12480000 0x100>;
+ clocks = <&gcc GSBI2_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ i2c2: i2c@124a0000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x124a0000 0x1000>;
+ interrupts = <0 196 IRQ_TYPE_NONE>;
+ clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
gsbi7: gsbi@16600000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";