[SCSI] lpfc 8.3.0 : Fix issue with assumed Interrupt Enable Block support
The phba hbq_get address was setup before the HBA reported support for
Interrupt Enable Block (INB). This caused loopback tests to fail
after all HBQs had been used once. Moved setting of hba_get until
after config port mailbox command completes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
diff --git a/drivers/scsi/lpfc/lpfc_mbox.c b/drivers/scsi/lpfc/lpfc_mbox.c
index dcdb7c9..5bb376b 100644
--- a/drivers/scsi/lpfc/lpfc_mbox.c
+++ b/drivers/scsi/lpfc/lpfc_mbox.c
@@ -1198,16 +1198,11 @@
sizeof(*phba->host_gp));
}
- /* Setup Port Group ring pointer */
- if (phba->sli3_options & LPFC_SLI3_INB_ENABLED) {
- pgp_offset = offsetof(struct lpfc_sli2_slim,
- mbx.us.s3_inb_pgp.port);
- phba->hbq_get = phba->mbox->us.s3_inb_pgp.hbq_get;
- } else if (phba->sli_rev == 3) {
+ /* Setup Port Group offset */
+ if (phba->sli_rev == 3)
pgp_offset = offsetof(struct lpfc_sli2_slim,
mbx.us.s3_pgp.port);
- phba->hbq_get = phba->mbox->us.s3_pgp.hbq_get;
- } else
+ else
pgp_offset = offsetof(struct lpfc_sli2_slim, mbx.us.s2.port);
pdma_addr = phba->slim2p.phys + pgp_offset;
phba->pcb->pgpAddrHigh = putPaddrHigh(pdma_addr);
diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c
index 215f9a5..14f9336 100644
--- a/drivers/scsi/lpfc/lpfc_sli.c
+++ b/drivers/scsi/lpfc/lpfc_sli.c
@@ -3144,17 +3144,20 @@
phba->sli3_options |= LPFC_SLI3_CRP_ENABLED;
if (pmb->mb.un.varCfgPort.ginb) {
phba->sli3_options |= LPFC_SLI3_INB_ENABLED;
+ phba->hbq_get = phba->mbox->us.s3_inb_pgp.hbq_get;
phba->port_gp = phba->mbox->us.s3_inb_pgp.port;
phba->inb_ha_copy = &phba->mbox->us.s3_inb_pgp.ha_copy;
phba->inb_counter = &phba->mbox->us.s3_inb_pgp.counter;
phba->inb_last_counter =
phba->mbox->us.s3_inb_pgp.counter;
} else {
+ phba->hbq_get = phba->mbox->us.s3_pgp.hbq_get;
phba->port_gp = phba->mbox->us.s3_pgp.port;
phba->inb_ha_copy = NULL;
phba->inb_counter = NULL;
}
} else {
+ phba->hbq_get = NULL;
phba->port_gp = phba->mbox->us.s2.port;
phba->inb_ha_copy = NULL;
phba->inb_counter = NULL;