V4L/DVB (4961): Add support for the ASUS P7131 remote control
Besides adding the board specific code, this patch moves
the RC5 decoding code from bt8xx to ir-functions.c to make it available
for all drivers.
Signed-off-by: Marc Fargas <telenieko.telenieko.com>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
diff --git a/drivers/media/common/ir-functions.c b/drivers/media/common/ir-functions.c
index 9a8dd87..cbf7c05 100644
--- a/drivers/media/common/ir-functions.c
+++ b/drivers/media/common/ir-functions.c
@@ -256,6 +256,112 @@
return value;
}
+/* RC5 decoding stuff, moved from bttv-input.c to share it with
+ * saa7134 */
+
+/* decode raw bit pattern to RC5 code */
+u32 ir_rc5_decode(unsigned int code)
+{
+ unsigned int org_code = code;
+ unsigned int pair;
+ unsigned int rc5 = 0;
+ int i;
+
+ for (i = 0; i < 14; ++i) {
+ pair = code & 0x3;
+ code >>= 2;
+
+ rc5 <<= 1;
+ switch (pair) {
+ case 0:
+ case 2:
+ break;
+ case 1:
+ rc5 |= 1;
+ break;
+ case 3:
+ dprintk(1, "ir-common: ir_rc5_decode(%x) bad code\n", org_code);
+ return 0;
+ }
+ }
+ dprintk(1, "ir-common: code=%x, rc5=%x, start=%x, toggle=%x, address=%x, "
+ "instr=%x\n", rc5, org_code, RC5_START(rc5),
+ RC5_TOGGLE(rc5), RC5_ADDR(rc5), RC5_INSTR(rc5));
+ return rc5;
+}
+
+void ir_rc5_timer_end(unsigned long data)
+{
+ struct card_ir *ir = (struct card_ir *)data;
+ struct timeval tv;
+ unsigned long current_jiffies, timeout;
+ u32 gap;
+ u32 rc5 = 0;
+
+ /* get time */
+ current_jiffies = jiffies;
+ do_gettimeofday(&tv);
+
+ /* avoid overflow with gap >1s */
+ if (tv.tv_sec - ir->base_time.tv_sec > 1) {
+ gap = 200000;
+ } else {
+ gap = 1000000 * (tv.tv_sec - ir->base_time.tv_sec) +
+ tv.tv_usec - ir->base_time.tv_usec;
+ }
+
+ /* Allow some timmer jitter (RC5 is ~24ms anyway so this is ok) */
+ if (gap < 28000) {
+ dprintk(1, "ir-common: spurious timer_end\n");
+ return;
+ }
+
+ ir->active = 0;
+ if (ir->last_bit < 20) {
+ /* ignore spurious codes (caused by light/other remotes) */
+ dprintk(1, "ir-common: short code: %x\n", ir->code);
+ } else {
+ ir->code = (ir->code << ir->shift_by) | 1;
+ rc5 = ir_rc5_decode(ir->code);
+
+ /* two start bits? */
+ if (RC5_START(rc5) != ir->start) {
+ dprintk(1, "ir-common: rc5 start bits invalid: %u\n", RC5_START(rc5));
+
+ /* right address? */
+ } else if (RC5_ADDR(rc5) == ir->addr) {
+ u32 toggle = RC5_TOGGLE(rc5);
+ u32 instr = RC5_INSTR(rc5);
+
+ /* Good code, decide if repeat/repress */
+ if (toggle != RC5_TOGGLE(ir->last_rc5) ||
+ instr != RC5_INSTR(ir->last_rc5)) {
+ dprintk(1, "ir-common: instruction %x, toggle %x\n", instr,
+ toggle);
+ ir_input_nokey(ir->dev, &ir->ir);
+ ir_input_keydown(ir->dev, &ir->ir, instr,
+ instr);
+ }
+
+ /* Set/reset key-up timer */
+ timeout = current_jiffies + (500 + ir->rc5_key_timeout
+ * HZ) / 1000;
+ mod_timer(&ir->timer_keyup, timeout);
+
+ /* Save code for repeat test */
+ ir->last_rc5 = rc5;
+ }
+ }
+}
+
+void ir_rc5_timer_keyup(unsigned long data)
+{
+ struct card_ir *ir = (struct card_ir *)data;
+
+ dprintk(1, "ir-common: key released\n");
+ ir_input_nokey(ir->dev, &ir->ir);
+}
+
EXPORT_SYMBOL_GPL(ir_input_init);
EXPORT_SYMBOL_GPL(ir_input_nokey);
EXPORT_SYMBOL_GPL(ir_input_keydown);
@@ -265,6 +371,10 @@
EXPORT_SYMBOL_GPL(ir_decode_biphase);
EXPORT_SYMBOL_GPL(ir_decode_pulsedistance);
+EXPORT_SYMBOL_GPL(ir_rc5_decode);
+EXPORT_SYMBOL_GPL(ir_rc5_timer_end);
+EXPORT_SYMBOL_GPL(ir_rc5_timer_keyup);
+
/*
* Local variables:
* c-basic-offset: 8