irqchip/gic-v3: Reset BPR during initialization
Currently, when running on FVP, CPU 0 boots up with its BPR changed from
the reset value. This renders it impossible to (preemptively) prioritize
interrupts on CPU 0.
This is harmless on normal systems since Linux typically does not
support preemptive interrupts. It does however cause problems in
systems with additional changes (such as patches for NMI simulation).
Many thanks to Andrew Thoelke for suggesting the BPR as having the
potential to harm preemption.
Suggested-by: Andrew Thoelke <andrew.thoelke@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
diff --git a/arch/arm/include/asm/arch_gicv3.h b/arch/arm/include/asm/arch_gicv3.h
index e08d151..dfe4002 100644
--- a/arch/arm/include/asm/arch_gicv3.h
+++ b/arch/arm/include/asm/arch_gicv3.h
@@ -34,6 +34,7 @@
#define ICC_CTLR __ACCESS_CP15(c12, 0, c12, 4)
#define ICC_SRE __ACCESS_CP15(c12, 0, c12, 5)
#define ICC_IGRPEN1 __ACCESS_CP15(c12, 0, c12, 7)
+#define ICC_BPR1 __ACCESS_CP15(c12, 0, c12, 3)
#define ICC_HSRE __ACCESS_CP15(c12, 4, c9, 5)
@@ -157,6 +158,11 @@
isb();
}
+static inline void gic_write_bpr1(u32 val)
+{
+ asm volatile("mcr " __stringify(ICC_BPR1) : : "r" (val));
+}
+
/*
* Even in 32bit systems that use LPAE, there is no guarantee that the I/O
* interface provides true 64bit atomic accesses, so using strd/ldrd doesn't
diff --git a/arch/arm64/include/asm/arch_gicv3.h b/arch/arm64/include/asm/arch_gicv3.h
index 8ec88e5..fc2a0cb 100644
--- a/arch/arm64/include/asm/arch_gicv3.h
+++ b/arch/arm64/include/asm/arch_gicv3.h
@@ -28,6 +28,7 @@
#define ICC_CTLR_EL1 sys_reg(3, 0, 12, 12, 4)
#define ICC_SRE_EL1 sys_reg(3, 0, 12, 12, 5)
#define ICC_GRPEN1_EL1 sys_reg(3, 0, 12, 12, 7)
+#define ICC_BPR1_EL1 sys_reg(3, 0, 12, 12, 3)
#define ICC_SRE_EL2 sys_reg(3, 4, 12, 9, 5)
@@ -165,6 +166,11 @@
isb();
}
+static inline void gic_write_bpr1(u32 val)
+{
+ asm volatile("msr_s " __stringify(ICC_BPR1_EL1) ", %0" : : "r" (val));
+}
+
#define gic_read_typer(c) readq_relaxed(c)
#define gic_write_irouter(v, c) writeq_relaxed(v, c)
diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
index ede5672..ecc5b23 100644
--- a/drivers/irqchip/irq-gic-v3.c
+++ b/drivers/irqchip/irq-gic-v3.c
@@ -495,6 +495,14 @@
/* Set priority mask register */
gic_write_pmr(DEFAULT_PMR_VALUE);
+ /*
+ * Some firmwares hand over to the kernel with the BPR changed from
+ * its reset value (and with a value large enough to prevent
+ * any pre-emptive interrupts from working at all). Writing a zero
+ * to BPR restores is reset value.
+ */
+ gic_write_bpr1(0);
+
if (static_key_true(&supports_deactivate)) {
/* EOI drops priority only (mode 1) */
gic_write_ctlr(ICC_CTLR_EL1_EOImode_drop);