diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 214a92d..3320e77 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2362,6 +2362,14 @@
 	  Some boards that use the Discovery chipset are the Momenco
 	  Ocelot C and Jaguar ATX and Pegasos II.
 
+config XILINX_LL_TEMAC
+	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
+	select PHYLIB
+	depends on PPC_DCR_NATIVE
+	help
+	  This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
+	  core used in Xilinx Spartan and Virtex FPGAs
+
 config QLA3XXX
 	tristate "QLogic QLA3XXX Network Driver Support"
 	depends on PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 1fc4602..80420f6 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -134,6 +134,8 @@
 
 obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
+ll_temac-objs := ll_temac_main.o ll_temac_mdio.o
+obj-$(CONFIG_XILINX_LL_TEMAC) += ll_temac.o
 obj-$(CONFIG_QLA3XXX) += qla3xxx.o
 obj-$(CONFIG_QLGE) += qlge/
 
diff --git a/drivers/net/ll_temac.h b/drivers/net/ll_temac.h
new file mode 100644
index 0000000..1af66a1
--- /dev/null
+++ b/drivers/net/ll_temac.h
@@ -0,0 +1,374 @@
+
+#ifndef XILINX_LL_TEMAC_H
+#define XILINX_LL_TEMAC_H
+
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/spinlock.h>
+#include <asm/dcr.h>
+#include <asm/dcr-regs.h>
+
+/* packet size info */
+#define XTE_HDR_SIZE			14      /* size of Ethernet header */
+#define XTE_TRL_SIZE			4       /* size of Ethernet trailer (FCS) */
+#define XTE_JUMBO_MTU			9000
+#define XTE_MAX_JUMBO_FRAME_SIZE	(XTE_JUMBO_MTU + XTE_HDR_SIZE + XTE_TRL_SIZE)
+
+/*  Configuration options */
+
+/*  Accept all incoming packets.
+ *  This option defaults to disabled (cleared) */
+#define XTE_OPTION_PROMISC                      (1 << 0)
+/*  Jumbo frame support for Tx & Rx.
+ *  This option defaults to disabled (cleared) */
+#define XTE_OPTION_JUMBO                        (1 << 1)
+/*  VLAN Rx & Tx frame support.
+ *  This option defaults to disabled (cleared) */
+#define XTE_OPTION_VLAN                         (1 << 2)
+/*  Enable recognition of flow control frames on Rx
+ *  This option defaults to enabled (set) */
+#define XTE_OPTION_FLOW_CONTROL                 (1 << 4)
+/*  Strip FCS and PAD from incoming frames.
+ *  Note: PAD from VLAN frames is not stripped.
+ *  This option defaults to disabled (set) */
+#define XTE_OPTION_FCS_STRIP                    (1 << 5)
+/*  Generate FCS field and add PAD automatically for outgoing frames.
+ *  This option defaults to enabled (set) */
+#define XTE_OPTION_FCS_INSERT                   (1 << 6)
+/*  Enable Length/Type error checking for incoming frames. When this option is
+set, the MAC will filter frames that have a mismatched type/length field
+and if XTE_OPTION_REPORT_RXERR is set, the user is notified when these
+types of frames are encountered. When this option is cleared, the MAC will
+allow these types of frames to be received.
+This option defaults to enabled (set) */
+#define XTE_OPTION_LENTYPE_ERR                  (1 << 7)
+/*  Enable the transmitter.
+ *  This option defaults to enabled (set) */
+#define XTE_OPTION_TXEN                         (1 << 11)
+/*  Enable the receiver
+*   This option defaults to enabled (set) */
+#define XTE_OPTION_RXEN                         (1 << 12)
+
+/*  Default options set when device is initialized or reset */
+#define XTE_OPTION_DEFAULTS                     \
+	(XTE_OPTION_TXEN |                          \
+	 XTE_OPTION_FLOW_CONTROL |                  \
+	 XTE_OPTION_RXEN)
+
+/* XPS_LL_TEMAC SDMA registers definition */
+
+#define TX_NXTDESC_PTR      0x00            /* r */
+#define TX_CURBUF_ADDR      0x01            /* r */
+#define TX_CURBUF_LENGTH    0x02            /* r */
+#define TX_CURDESC_PTR      0x03            /* rw */
+#define TX_TAILDESC_PTR     0x04            /* rw */
+#define TX_CHNL_CTRL        0x05            /* rw */
+/*
+ 0:7      24:31       IRQTimeout
+ 8:15     16:23       IRQCount
+ 16:20    11:15       Reserved
+ 21       10          0
+ 22       9           UseIntOnEnd
+ 23       8           LdIRQCnt
+ 24       7           IRQEn
+ 25:28    3:6         Reserved
+ 29       2           IrqErrEn
+ 30       1           IrqDlyEn
+ 31       0           IrqCoalEn
+*/
+#define CHNL_CTRL_IRQ_IOE       (1 << 9)
+#define CHNL_CTRL_IRQ_EN        (1 << 7)
+#define CHNL_CTRL_IRQ_ERR_EN    (1 << 2)
+#define CHNL_CTRL_IRQ_DLY_EN    (1 << 1)
+#define CHNL_CTRL_IRQ_COAL_EN   (1 << 0)
+#define TX_IRQ_REG          0x06            /* rw */
+/*
+  0:7      24:31       DltTmrValue
+ 8:15     16:23       ClscCntrValue
+ 16:17    14:15       Reserved
+ 18:21    10:13       ClscCnt
+ 22:23    8:9         DlyCnt
+ 24:28    3::7        Reserved
+ 29       2           ErrIrq
+ 30       1           DlyIrq
+ 31       0           CoalIrq
+ */
+#define TX_CHNL_STS         0x07            /* r */
+/*
+   0:9      22:31   Reserved
+ 10       21      TailPErr
+ 11       20      CmpErr
+ 12       19      AddrErr
+ 13       18      NxtPErr
+ 14       17      CurPErr
+ 15       16      BsyWr
+ 16:23    8:15    Reserved
+ 24       7       Error
+ 25       6       IOE
+ 26       5       SOE
+ 27       4       Cmplt
+ 28       3       SOP
+ 29       2       EOP
+ 30       1       EngBusy
+ 31       0       Reserved
+*/
+
+#define RX_NXTDESC_PTR      0x08            /* r */
+#define RX_CURBUF_ADDR      0x09            /* r */
+#define RX_CURBUF_LENGTH    0x0a            /* r */
+#define RX_CURDESC_PTR      0x0b            /* rw */
+#define RX_TAILDESC_PTR     0x0c            /* rw */
+#define RX_CHNL_CTRL        0x0d            /* rw */
+/*
+ 0:7      24:31       IRQTimeout
+ 8:15     16:23       IRQCount
+ 16:20    11:15       Reserved
+ 21       10          0
+ 22       9           UseIntOnEnd
+ 23       8           LdIRQCnt
+ 24       7           IRQEn
+ 25:28    3:6         Reserved
+ 29       2           IrqErrEn
+ 30       1           IrqDlyEn
+ 31       0           IrqCoalEn
+ */
+#define RX_IRQ_REG          0x0e            /* rw */
+#define IRQ_COAL        (1 << 0)
+#define IRQ_DLY         (1 << 1)
+#define IRQ_ERR         (1 << 2)
+#define IRQ_DMAERR      (1 << 7)            /* this is not documented ??? */
+/*
+ 0:7      24:31       DltTmrValue
+ 8:15     16:23       ClscCntrValue
+ 16:17    14:15       Reserved
+ 18:21    10:13       ClscCnt
+ 22:23    8:9         DlyCnt
+ 24:28    3::7        Reserved
+*/
+#define RX_CHNL_STS         0x0f        /* r */
+#define CHNL_STS_ENGBUSY    (1 << 1)
+#define CHNL_STS_EOP        (1 << 2)
+#define CHNL_STS_SOP        (1 << 3)
+#define CHNL_STS_CMPLT      (1 << 4)
+#define CHNL_STS_SOE        (1 << 5)
+#define CHNL_STS_IOE        (1 << 6)
+#define CHNL_STS_ERR        (1 << 7)
+
+#define CHNL_STS_BSYWR      (1 << 16)
+#define CHNL_STS_CURPERR    (1 << 17)
+#define CHNL_STS_NXTPERR    (1 << 18)
+#define CHNL_STS_ADDRERR    (1 << 19)
+#define CHNL_STS_CMPERR     (1 << 20)
+#define CHNL_STS_TAILERR    (1 << 21)
+/*
+ 0:9      22:31   Reserved
+ 10       21      TailPErr
+ 11       20      CmpErr
+ 12       19      AddrErr
+ 13       18      NxtPErr
+ 14       17      CurPErr
+ 15       16      BsyWr
+ 16:23    8:15    Reserved
+ 24       7       Error
+ 25       6       IOE
+ 26       5       SOE
+ 27       4       Cmplt
+ 28       3       SOP
+ 29       2       EOP
+ 30       1       EngBusy
+ 31       0       Reserved
+*/
+
+#define DMA_CONTROL_REG             0x10            /* rw */
+#define DMA_CONTROL_RST                 (1 << 0)
+#define DMA_TAIL_ENABLE                 (1 << 2)
+
+/* XPS_LL_TEMAC direct registers definition */
+
+#define XTE_RAF0_OFFSET              0x00
+#define RAF0_RST                        (1 << 0)
+#define RAF0_MCSTREJ                    (1 << 1)
+#define RAF0_BCSTREJ                    (1 << 2)
+#define XTE_TPF0_OFFSET              0x04
+#define XTE_IFGP0_OFFSET             0x08
+#define XTE_ISR0_OFFSET              0x0c
+#define ISR0_HARDACSCMPLT               (1 << 0)
+#define ISR0_AUTONEG                    (1 << 1)
+#define ISR0_RXCMPLT                    (1 << 2)
+#define ISR0_RXREJ                      (1 << 3)
+#define ISR0_RXFIFOOVR                  (1 << 4)
+#define ISR0_TXCMPLT                    (1 << 5)
+#define ISR0_RXDCMLCK                   (1 << 6)
+
+#define XTE_IPR0_OFFSET              0x10
+#define XTE_IER0_OFFSET              0x14
+
+#define XTE_MSW0_OFFSET              0x20
+#define XTE_LSW0_OFFSET              0x24
+#define XTE_CTL0_OFFSET              0x28
+#define XTE_RDY0_OFFSET              0x2c
+
+#define XTE_RSE_MIIM_RR_MASK      0x0002
+#define XTE_RSE_MIIM_WR_MASK      0x0004
+#define XTE_RSE_CFG_RR_MASK       0x0020
+#define XTE_RSE_CFG_WR_MASK       0x0040
+#define XTE_RDY0_HARD_ACS_RDY_MASK  (0x10000)
+
+/* XPS_LL_TEMAC indirect registers offset definition */
+
+#define	XTE_RXC0_OFFSET			0x00000200 /* Rx configuration word 0 */
+#define	XTE_RXC1_OFFSET			0x00000240 /* Rx configuration word 1 */
+#define XTE_RXC1_RXRST_MASK		(1 << 31)  /* Receiver reset */
+#define XTE_RXC1_RXJMBO_MASK		(1 << 30)  /* Jumbo frame enable */
+#define XTE_RXC1_RXFCS_MASK		(1 << 29)  /* FCS not stripped */
+#define XTE_RXC1_RXEN_MASK		(1 << 28)  /* Receiver enable */
+#define XTE_RXC1_RXVLAN_MASK		(1 << 27)  /* VLAN enable */
+#define XTE_RXC1_RXHD_MASK		(1 << 26)  /* Half duplex */
+#define XTE_RXC1_RXLT_MASK		(1 << 25)  /* Length/type check disable */
+
+#define XTE_TXC_OFFSET			0x00000280 /*  Tx configuration */
+#define XTE_TXC_TXRST_MASK		(1 << 31)  /* Transmitter reset */
+#define XTE_TXC_TXJMBO_MASK		(1 << 30)  /* Jumbo frame enable */
+#define XTE_TXC_TXFCS_MASK		(1 << 29)  /* Generate FCS */
+#define XTE_TXC_TXEN_MASK		(1 << 28)  /* Transmitter enable */
+#define XTE_TXC_TXVLAN_MASK		(1 << 27)  /* VLAN enable */
+#define XTE_TXC_TXHD_MASK		(1 << 26)  /* Half duplex */
+
+#define XTE_FCC_OFFSET			0x000002C0 /* Flow control config */
+#define XTE_FCC_RXFLO_MASK		(1 << 29)  /* Rx flow control enable */
+#define XTE_FCC_TXFLO_MASK		(1 << 30)  /* Tx flow control enable */
+
+#define XTE_EMCFG_OFFSET		0x00000300 /* EMAC configuration */
+#define XTE_EMCFG_LINKSPD_MASK		0xC0000000 /* Link speed */
+#define XTE_EMCFG_HOSTEN_MASK		(1 << 26)  /* Host interface enable */
+#define XTE_EMCFG_LINKSPD_10		0x00000000 /* 10 Mbit LINKSPD_MASK */
+#define XTE_EMCFG_LINKSPD_100		(1 << 30)  /* 100 Mbit LINKSPD_MASK */
+#define XTE_EMCFG_LINKSPD_1000		(1 << 31)  /* 1000 Mbit LINKSPD_MASK */
+
+#define XTE_GMIC_OFFSET			0x00000320 /* RGMII/SGMII config */
+#define XTE_MC_OFFSET			0x00000340 /* MDIO configuration */
+#define XTE_UAW0_OFFSET			0x00000380 /* Unicast address word 0 */
+#define XTE_UAW1_OFFSET			0x00000384 /* Unicast address word 1 */
+
+#define XTE_MAW0_OFFSET			0x00000388 /* Multicast addr word 0 */
+#define XTE_MAW1_OFFSET			0x0000038C /* Multicast addr word 1 */
+#define XTE_AFM_OFFSET			0x00000390 /* Promiscuous mode */
+#define XTE_AFM_EPPRM_MASK		(1 << 31)  /* Promiscuous mode enable */
+
+/* Interrupt Request status */
+#define XTE_TIS_OFFSET			0x000003A0
+#define TIS_FRIS			(1 << 0)
+#define TIS_MRIS			(1 << 1)
+#define TIS_MWIS			(1 << 2)
+#define TIS_ARIS			(1 << 3)
+#define TIS_AWIS			(1 << 4)
+#define TIS_CRIS			(1 << 5)
+#define TIS_CWIS			(1 << 6)
+
+#define XTE_TIE_OFFSET			0x000003A4 /* Interrupt enable */
+
+/**  MII Mamagement Control register (MGTCR) */
+#define XTE_MGTDR_OFFSET		0x000003B0 /* MII data */
+#define XTE_MIIMAI_OFFSET		0x000003B4 /* MII control */
+
+#define CNTLREG_WRITE_ENABLE_MASK   0x8000
+#define CNTLREG_EMAC1SEL_MASK       0x0400
+#define CNTLREG_ADDRESSCODE_MASK    0x03ff
+
+/* CDMAC descriptor status bit definitions */
+
+#define STS_CTRL_APP0_ERR         (1 << 31)
+#define STS_CTRL_APP0_IRQONEND    (1 << 30)
+/* undoccumented */
+#define STS_CTRL_APP0_STOPONEND   (1 << 29)
+#define STS_CTRL_APP0_CMPLT       (1 << 28)
+#define STS_CTRL_APP0_SOP         (1 << 27)
+#define STS_CTRL_APP0_EOP         (1 << 26)
+#define STS_CTRL_APP0_ENGBUSY     (1 << 25)
+/* undocumented */
+#define STS_CTRL_APP0_ENGRST      (1 << 24)
+
+#define TX_CONTROL_CALC_CSUM_MASK   1
+
+#define XTE_ALIGN       32
+#define BUFFER_ALIGN(adr) ((XTE_ALIGN - ((u32) adr)) % XTE_ALIGN)
+
+#define MULTICAST_CAM_TABLE_NUM 4
+
+/* TX/RX CURDESC_PTR points to first descriptor */
+/* TX/RX TAILDESC_PTR points to last descriptor in linked list */
+
+/**
+ * struct cdmac_bd - LocalLink buffer descriptor format
+ *
+ * app0 bits:
+ *	0    Error
+ *	1    IrqOnEnd    generate an interrupt at completion of DMA  op
+ *	2    reserved
+ *	3    completed   Current descriptor completed
+ *	4    SOP         TX - marks first desc/ RX marks first desct
+ *	5    EOP         TX marks last desc/RX marks last desc
+ *	6    EngBusy     DMA is processing
+ *	7    reserved
+ *	8:31 application specific
+ */
+struct cdmac_bd {
+	u32 next;	/* Physical address of next buffer descriptor */
+	u32 phys;
+	u32 len;
+	u32 app0;
+	u32 app1;	/* TX start << 16 | insert */
+	u32 app2;	/* TX csum */
+	u32 app3;
+	u32 app4;	/* skb for TX length for RX */
+};
+
+struct temac_local {
+	struct net_device *ndev;
+	struct device *dev;
+
+	/* Connection to PHY device */
+	struct phy_device *phy_dev;	/* Pointer to PHY device */
+	struct device_node *phy_node;
+
+	/* MDIO bus data */
+	struct mii_bus *mii_bus;	/* MII bus reference */
+	int mdio_irqs[PHY_MAX_ADDR];	/* IRQs table for MDIO bus */
+
+	/* IO registers and IRQs */
+	void __iomem *regs;
+	dcr_host_t sdma_dcrs;
+	int tx_irq;
+	int rx_irq;
+	int emac_num;
+
+	struct sk_buff **rx_skb;
+	spinlock_t rx_lock;
+	struct mutex indirect_mutex;
+	u32 options;			/* Current options word */
+	int last_link;
+
+	/* Buffer descriptors */
+	struct cdmac_bd *tx_bd_v;
+	dma_addr_t tx_bd_p;
+	struct cdmac_bd *rx_bd_v;
+	dma_addr_t rx_bd_p;
+	int tx_bd_ci;
+	int tx_bd_next;
+	int tx_bd_tail;
+	int rx_bd_ci;
+};
+
+/* xilinx_temac.c */
+u32 temac_ior(struct temac_local *lp, int offset);
+void temac_iow(struct temac_local *lp, int offset, u32 value);
+int temac_indirect_busywait(struct temac_local *lp);
+u32 temac_indirect_in32(struct temac_local *lp, int reg);
+void temac_indirect_out32(struct temac_local *lp, int reg, u32 value);
+
+
+/* xilinx_temac_mdio.c */
+int temac_mdio_setup(struct temac_local *lp, struct device_node *np);
+void temac_mdio_teardown(struct temac_local *lp);
+
+#endif /* XILINX_LL_TEMAC_H */
diff --git a/drivers/net/ll_temac_main.c b/drivers/net/ll_temac_main.c
new file mode 100644
index 0000000..96e7248
--- /dev/null
+++ b/drivers/net/ll_temac_main.c
@@ -0,0 +1,969 @@
+/*
+ * Driver for Xilinx TEMAC Ethernet device
+ *
+ * Copyright (c) 2008 Nissin Systems Co., Ltd.,  Yoshio Kashiwagi
+ * Copyright (c) 2005-2008 DLA Systems,  David H. Lynch Jr. <dhlii@dlasys.net>
+ * Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
+ *
+ * This is a driver for the Xilinx ll_temac ipcore which is often used
+ * in the Virtex and Spartan series of chips.
+ *
+ * Notes:
+ * - The ll_temac hardware uses indirect access for many of the TEMAC
+ *   registers, include the MDIO bus.  However, indirect access to MDIO
+ *   registers take considerably more clock cycles than to TEMAC registers.
+ *   MDIO accesses are long, so threads doing them should probably sleep
+ *   rather than busywait.  However, since only one indirect access can be
+ *   in progress at any given time, that means that *all* indirect accesses
+ *   could end up sleeping (to wait for an MDIO access to complete).
+ *   Fortunately none of the indirect accesses are on the 'hot' path for tx
+ *   or rx, so this should be okay.
+ *
+ * TODO:
+ * - Fix driver to work on more than just Virtex5.  Right now the driver
+ *   assumes that the locallink DMA registers are accessed via DCR
+ *   instructions.
+ * - Factor out locallink DMA code into separate driver
+ * - Fix multicast assignment.
+ * - Fix support for hardware checksumming.
+ * - Testing.  Lots and lots of testing.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/init.h>
+#include <linux/mii.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_mdio.h>
+#include <linux/of_platform.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/tcp.h>      /* needed for sizeof(tcphdr) */
+#include <linux/udp.h>      /* needed for sizeof(udphdr) */
+#include <linux/phy.h>
+#include <linux/in.h>
+#include <linux/io.h>
+#include <linux/ip.h>
+
+#include "ll_temac.h"
+
+#define TX_BD_NUM   64
+#define RX_BD_NUM   128
+
+/* ---------------------------------------------------------------------
+ * Low level register access functions
+ */
+
+u32 temac_ior(struct temac_local *lp, int offset)
+{
+	return in_be32((u32 *)(lp->regs + offset));
+}
+
+void temac_iow(struct temac_local *lp, int offset, u32 value)
+{
+	out_be32((u32 *) (lp->regs + offset), value);
+}
+
+int temac_indirect_busywait(struct temac_local *lp)
+{
+	long end = jiffies + 2;
+
+	while (!(temac_ior(lp, XTE_RDY0_OFFSET) & XTE_RDY0_HARD_ACS_RDY_MASK)) {
+		if (end - jiffies <= 0) {
+			WARN_ON(1);
+			return -ETIMEDOUT;
+		}
+		msleep(1);
+	}
+	return 0;
+}
+
+/**
+ * temac_indirect_in32
+ *
+ * lp->indirect_mutex must be held when calling this function
+ */
+u32 temac_indirect_in32(struct temac_local *lp, int reg)
+{
+	u32 val;
+
+	if (temac_indirect_busywait(lp))
+		return -ETIMEDOUT;
+	temac_iow(lp, XTE_CTL0_OFFSET, reg);
+	if (temac_indirect_busywait(lp))
+		return -ETIMEDOUT;
+	val = temac_ior(lp, XTE_LSW0_OFFSET);
+
+	return val;
+}
+
+/**
+ * temac_indirect_out32
+ *
+ * lp->indirect_mutex must be held when calling this function
+ */
+void temac_indirect_out32(struct temac_local *lp, int reg, u32 value)
+{
+	if (temac_indirect_busywait(lp))
+		return;
+	temac_iow(lp, XTE_LSW0_OFFSET, value);
+	temac_iow(lp, XTE_CTL0_OFFSET, CNTLREG_WRITE_ENABLE_MASK | reg);
+}
+
+static u32 temac_dma_in32(struct temac_local *lp, int reg)
+{
+	return dcr_read(lp->sdma_dcrs, reg);
+}
+
+static void temac_dma_out32(struct temac_local *lp, int reg, u32 value)
+{
+	dcr_write(lp->sdma_dcrs, reg, value);
+}
+
+/**
+ * temac_dma_bd_init - Setup buffer descriptor rings
+ */
+static int temac_dma_bd_init(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	struct sk_buff *skb;
+	int i;
+
+	lp->rx_skb = kzalloc(sizeof(struct sk_buff)*RX_BD_NUM, GFP_KERNEL);
+	/* allocate the tx and rx ring buffer descriptors. */
+	/* returns a virtual addres and a physical address. */
+	lp->tx_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					 sizeof(*lp->tx_bd_v) * TX_BD_NUM,
+					 &lp->tx_bd_p, GFP_KERNEL);
+	lp->rx_bd_v = dma_alloc_coherent(ndev->dev.parent,
+					 sizeof(*lp->rx_bd_v) * RX_BD_NUM,
+					 &lp->rx_bd_p, GFP_KERNEL);
+
+	memset(lp->tx_bd_v, 0, sizeof(*lp->tx_bd_v) * TX_BD_NUM);
+	for (i = 0; i < TX_BD_NUM; i++) {
+		lp->tx_bd_v[i].next = lp->tx_bd_p +
+				sizeof(*lp->tx_bd_v) * ((i + 1) % TX_BD_NUM);
+	}
+
+	memset(lp->rx_bd_v, 0, sizeof(*lp->rx_bd_v) * RX_BD_NUM);
+	for (i = 0; i < RX_BD_NUM; i++) {
+		lp->rx_bd_v[i].next = lp->rx_bd_p +
+				sizeof(*lp->rx_bd_v) * ((i + 1) % RX_BD_NUM);
+
+		skb = alloc_skb(XTE_MAX_JUMBO_FRAME_SIZE
+				+ XTE_ALIGN, GFP_ATOMIC);
+		if (skb == 0) {
+			dev_err(&ndev->dev, "alloc_skb error %d\n", i);
+			return -1;
+		}
+		lp->rx_skb[i] = skb;
+		skb_reserve(skb,  BUFFER_ALIGN(skb->data));
+		/* returns physical address of skb->data */
+		lp->rx_bd_v[i].phys = dma_map_single(ndev->dev.parent,
+						     skb->data,
+						     XTE_MAX_JUMBO_FRAME_SIZE,
+						     DMA_FROM_DEVICE);
+		lp->rx_bd_v[i].len = XTE_MAX_JUMBO_FRAME_SIZE;
+		lp->rx_bd_v[i].app0 = STS_CTRL_APP0_IRQONEND;
+	}
+
+	temac_dma_out32(lp, TX_CHNL_CTRL, 0x10220400 |
+					  CHNL_CTRL_IRQ_EN |
+					  CHNL_CTRL_IRQ_DLY_EN |
+					  CHNL_CTRL_IRQ_COAL_EN);
+	/* 0x10220483 */
+	/* 0x00100483 */
+	temac_dma_out32(lp, RX_CHNL_CTRL, 0xff010000 |
+					  CHNL_CTRL_IRQ_EN |
+					  CHNL_CTRL_IRQ_DLY_EN |
+					  CHNL_CTRL_IRQ_COAL_EN |
+					  CHNL_CTRL_IRQ_IOE);
+	/* 0xff010283 */
+
+	temac_dma_out32(lp, RX_CURDESC_PTR,  lp->rx_bd_p);
+	temac_dma_out32(lp, RX_TAILDESC_PTR,
+		       lp->rx_bd_p + (sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
+	temac_dma_out32(lp, TX_CURDESC_PTR, lp->tx_bd_p);
+
+	return 0;
+}
+
+/* ---------------------------------------------------------------------
+ * net_device_ops
+ */
+
+static int temac_set_mac_address(struct net_device *ndev, void *address)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+
+	if (address)
+		memcpy(ndev->dev_addr, address, ETH_ALEN);
+
+	if (!is_valid_ether_addr(ndev->dev_addr))
+		random_ether_addr(ndev->dev_addr);
+
+	/* set up unicast MAC address filter set its mac address */
+	mutex_lock(&lp->indirect_mutex);
+	temac_indirect_out32(lp, XTE_UAW0_OFFSET,
+			     (ndev->dev_addr[0]) |
+			     (ndev->dev_addr[1] << 8) |
+			     (ndev->dev_addr[2] << 16) |
+			     (ndev->dev_addr[3] << 24));
+	/* There are reserved bits in EUAW1
+	 * so don't affect them Set MAC bits [47:32] in EUAW1 */
+	temac_indirect_out32(lp, XTE_UAW1_OFFSET,
+			     (ndev->dev_addr[4] & 0x000000ff) |
+			     (ndev->dev_addr[5] << 8));
+	mutex_unlock(&lp->indirect_mutex);
+
+	return 0;
+}
+
+static void temac_set_multicast_list(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	u32 multi_addr_msw, multi_addr_lsw, val;
+	int i;
+
+	mutex_lock(&lp->indirect_mutex);
+	if (ndev->flags & (IFF_ALLMULTI | IFF_PROMISC)
+			|| ndev->mc_count > MULTICAST_CAM_TABLE_NUM) {
+		/*
+		 *	We must make the kernel realise we had to move
+		 *	into promisc mode or we start all out war on
+		 *	the cable. If it was a promisc request the
+		 *	flag is already set. If not we assert it.
+		 */
+		ndev->flags |= IFF_PROMISC;
+		temac_indirect_out32(lp, XTE_AFM_OFFSET, XTE_AFM_EPPRM_MASK);
+		dev_info(&ndev->dev, "Promiscuous mode enabled.\n");
+	} else if (ndev->mc_count) {
+		struct dev_mc_list *mclist = ndev->mc_list;
+		for (i = 0; mclist && i < ndev->mc_count; i++) {
+
+			if (i >= MULTICAST_CAM_TABLE_NUM)
+				break;
+			multi_addr_msw = ((mclist->dmi_addr[3] << 24) |
+					  (mclist->dmi_addr[2] << 16) |
+					  (mclist->dmi_addr[1] << 8) |
+					  (mclist->dmi_addr[0]));
+			temac_indirect_out32(lp, XTE_MAW0_OFFSET,
+					     multi_addr_msw);
+			multi_addr_lsw = ((mclist->dmi_addr[5] << 8) |
+					  (mclist->dmi_addr[4]) | (i << 16));
+			temac_indirect_out32(lp, XTE_MAW1_OFFSET,
+					     multi_addr_lsw);
+			mclist = mclist->next;
+		}
+	} else {
+		val = temac_indirect_in32(lp, XTE_AFM_OFFSET);
+		temac_indirect_out32(lp, XTE_AFM_OFFSET,
+				     val & ~XTE_AFM_EPPRM_MASK);
+		temac_indirect_out32(lp, XTE_MAW0_OFFSET, 0);
+		temac_indirect_out32(lp, XTE_MAW1_OFFSET, 0);
+		dev_info(&ndev->dev, "Promiscuous mode disabled.\n");
+	}
+	mutex_unlock(&lp->indirect_mutex);
+}
+
+struct temac_option {
+	int flg;
+	u32 opt;
+	u32 reg;
+	u32 m_or;
+	u32 m_and;
+} temac_options[] = {
+	/* Turn on jumbo packet support for both Rx and Tx */
+	{
+		.opt = XTE_OPTION_JUMBO,
+		.reg = XTE_TXC_OFFSET,
+		.m_or = XTE_TXC_TXJMBO_MASK,
+	},
+	{
+		.opt = XTE_OPTION_JUMBO,
+		.reg = XTE_RXC1_OFFSET,
+		.m_or =XTE_RXC1_RXJMBO_MASK,
+	},
+	/* Turn on VLAN packet support for both Rx and Tx */
+	{
+		.opt = XTE_OPTION_VLAN,
+		.reg = XTE_TXC_OFFSET,
+		.m_or =XTE_TXC_TXVLAN_MASK,
+	},
+	{
+		.opt = XTE_OPTION_VLAN,
+		.reg = XTE_RXC1_OFFSET,
+		.m_or =XTE_RXC1_RXVLAN_MASK,
+	},
+	/* Turn on FCS stripping on receive packets */
+	{
+		.opt = XTE_OPTION_FCS_STRIP,
+		.reg = XTE_RXC1_OFFSET,
+		.m_or =XTE_RXC1_RXFCS_MASK,
+	},
+	/* Turn on FCS insertion on transmit packets */
+	{
+		.opt = XTE_OPTION_FCS_INSERT,
+		.reg = XTE_TXC_OFFSET,
+		.m_or =XTE_TXC_TXFCS_MASK,
+	},
+	/* Turn on length/type field checking on receive packets */
+	{
+		.opt = XTE_OPTION_LENTYPE_ERR,
+		.reg = XTE_RXC1_OFFSET,
+		.m_or =XTE_RXC1_RXLT_MASK,
+	},
+	/* Turn on flow control */
+	{
+		.opt = XTE_OPTION_FLOW_CONTROL,
+		.reg = XTE_FCC_OFFSET,
+		.m_or =XTE_FCC_RXFLO_MASK,
+	},
+	/* Turn on flow control */
+	{
+		.opt = XTE_OPTION_FLOW_CONTROL,
+		.reg = XTE_FCC_OFFSET,
+		.m_or =XTE_FCC_TXFLO_MASK,
+	},
+	/* Turn on promiscuous frame filtering (all frames are received ) */
+	{
+		.opt = XTE_OPTION_PROMISC,
+		.reg = XTE_AFM_OFFSET,
+		.m_or =XTE_AFM_EPPRM_MASK,
+	},
+	/* Enable transmitter if not already enabled */
+	{
+		.opt = XTE_OPTION_TXEN,
+		.reg = XTE_TXC_OFFSET,
+		.m_or =XTE_TXC_TXEN_MASK,
+	},
+	/* Enable receiver? */
+	{
+		.opt = XTE_OPTION_RXEN,
+		.reg = XTE_RXC1_OFFSET,
+		.m_or =XTE_RXC1_RXEN_MASK,
+	},
+	{}
+};
+
+/**
+ * temac_setoptions
+ */
+static u32 temac_setoptions(struct net_device *ndev, u32 options)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	struct temac_option *tp = &temac_options[0];
+	int reg;
+
+	mutex_lock(&lp->indirect_mutex);
+	while (tp->opt) {
+		reg = temac_indirect_in32(lp, tp->reg) & ~tp->m_or;
+		if (options & tp->opt)
+			reg |= tp->m_or;
+		temac_indirect_out32(lp, tp->reg, reg);
+		tp++;
+	}
+	lp->options |= options;
+	mutex_unlock(&lp->indirect_mutex);
+
+	return (0);
+}
+
+/* Initilize temac */
+static void temac_device_reset(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	u32 timeout;
+	u32 val;
+
+	/* Perform a software reset */
+
+	/* 0x300 host enable bit ? */
+	/* reset PHY through control register ?:1 */
+
+	dev_dbg(&ndev->dev, "%s()\n", __func__);
+
+	mutex_lock(&lp->indirect_mutex);
+	/* Reset the receiver and wait for it to finish reset */
+	temac_indirect_out32(lp, XTE_RXC1_OFFSET, XTE_RXC1_RXRST_MASK);
+	timeout = 1000;
+	while (temac_indirect_in32(lp, XTE_RXC1_OFFSET) & XTE_RXC1_RXRST_MASK) {
+		udelay(1);
+		if (--timeout == 0) {
+			dev_err(&ndev->dev,
+				"temac_device_reset RX reset timeout!!\n");
+			break;
+		}
+	}
+
+	/* Reset the transmitter and wait for it to finish reset */
+	temac_indirect_out32(lp, XTE_TXC_OFFSET, XTE_TXC_TXRST_MASK);
+	timeout = 1000;
+	while (temac_indirect_in32(lp, XTE_TXC_OFFSET) & XTE_TXC_TXRST_MASK) {
+		udelay(1);
+		if (--timeout == 0) {
+			dev_err(&ndev->dev,
+				"temac_device_reset TX reset timeout!!\n");
+			break;
+		}
+	}
+
+	/* Disable the receiver */
+	val = temac_indirect_in32(lp, XTE_RXC1_OFFSET);
+	temac_indirect_out32(lp, XTE_RXC1_OFFSET, val & ~XTE_RXC1_RXEN_MASK);
+
+	/* Reset Local Link (DMA) */
+	temac_dma_out32(lp, DMA_CONTROL_REG, DMA_CONTROL_RST);
+	timeout = 1000;
+	while (temac_dma_in32(lp, DMA_CONTROL_REG) & DMA_CONTROL_RST) {
+		udelay(1);
+		if (--timeout == 0) {
+			dev_err(&ndev->dev,
+				"temac_device_reset DMA reset timeout!!\n");
+			break;
+		}
+	}
+	temac_dma_out32(lp, DMA_CONTROL_REG, DMA_TAIL_ENABLE);
+
+	temac_dma_bd_init(ndev);
+
+	temac_indirect_out32(lp, XTE_RXC0_OFFSET, 0);
+	temac_indirect_out32(lp, XTE_RXC1_OFFSET, 0);
+	temac_indirect_out32(lp, XTE_TXC_OFFSET, 0);
+	temac_indirect_out32(lp, XTE_FCC_OFFSET, XTE_FCC_RXFLO_MASK);
+
+	mutex_unlock(&lp->indirect_mutex);
+
+	/* Sync default options with HW
+	 * but leave receiver and transmitter disabled.  */
+	temac_setoptions(ndev,
+			 lp->options & ~(XTE_OPTION_TXEN | XTE_OPTION_RXEN));
+
+	temac_set_mac_address(ndev, NULL);
+
+	/* Set address filter table */
+	temac_set_multicast_list(ndev);
+	if (temac_setoptions(ndev, lp->options))
+		dev_err(&ndev->dev, "Error setting TEMAC options\n");
+
+	/* Init Driver variable */
+	ndev->trans_start = 0;
+}
+
+void temac_adjust_link(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	struct phy_device *phy = lp->phy_dev;
+	u32 mii_speed;
+	int link_state;
+
+	/* hash together the state values to decide if something has changed */
+	link_state = phy->speed | (phy->duplex << 1) | phy->link;
+
+	mutex_lock(&lp->indirect_mutex);
+	if (lp->last_link != link_state) {
+		mii_speed = temac_indirect_in32(lp, XTE_EMCFG_OFFSET);
+		mii_speed &= ~XTE_EMCFG_LINKSPD_MASK;
+
+		switch (phy->speed) {
+		case SPEED_1000: mii_speed |= XTE_EMCFG_LINKSPD_1000; break;
+		case SPEED_100: mii_speed |= XTE_EMCFG_LINKSPD_100; break;
+		case SPEED_10: mii_speed |= XTE_EMCFG_LINKSPD_10; break;
+		}
+
+		/* Write new speed setting out to TEMAC */
+		temac_indirect_out32(lp, XTE_EMCFG_OFFSET, mii_speed);
+		lp->last_link = link_state;
+		phy_print_status(phy);
+	}
+	mutex_unlock(&lp->indirect_mutex);
+}
+
+static void temac_start_xmit_done(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	struct cdmac_bd *cur_p;
+	unsigned int stat = 0;
+
+	cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
+	stat = cur_p->app0;
+
+	while (stat & STS_CTRL_APP0_CMPLT) {
+		dma_unmap_single(ndev->dev.parent, cur_p->phys, cur_p->len,
+				 DMA_TO_DEVICE);
+		if (cur_p->app4)
+			dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
+		cur_p->app0 = 0;
+
+		ndev->stats.tx_packets++;
+		ndev->stats.tx_bytes += cur_p->len;
+
+		lp->tx_bd_ci++;
+		if (lp->tx_bd_ci >= TX_BD_NUM)
+			lp->tx_bd_ci = 0;
+
+		cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
+		stat = cur_p->app0;
+	}
+
+	netif_wake_queue(ndev);
+}
+
+static int temac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	struct cdmac_bd *cur_p;
+	dma_addr_t start_p, tail_p;
+	int ii;
+	unsigned long num_frag;
+	skb_frag_t *frag;
+
+	num_frag = skb_shinfo(skb)->nr_frags;
+	frag = &skb_shinfo(skb)->frags[0];
+	start_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
+	cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
+
+	if (cur_p->app0 & STS_CTRL_APP0_CMPLT) {
+		if (!netif_queue_stopped(ndev)) {
+			netif_stop_queue(ndev);
+			return NETDEV_TX_BUSY;
+		}
+		return NETDEV_TX_BUSY;
+	}
+
+	cur_p->app0 = 0;
+	if (skb->ip_summed == CHECKSUM_PARTIAL) {
+		const struct iphdr *ip = ip_hdr(skb);
+		int length = 0, start = 0, insert = 0;
+
+		switch (ip->protocol) {
+		case IPPROTO_TCP:
+			start = sizeof(struct iphdr) + ETH_HLEN;
+			insert = sizeof(struct iphdr) + ETH_HLEN + 16;
+			length = ip->tot_len - sizeof(struct iphdr);
+			break;
+		case IPPROTO_UDP:
+			start = sizeof(struct iphdr) + ETH_HLEN;
+			insert = sizeof(struct iphdr) + ETH_HLEN + 6;
+			length = ip->tot_len - sizeof(struct iphdr);
+			break;
+		default:
+			break;
+		}
+		cur_p->app1 = ((start << 16) | insert);
+		cur_p->app2 = csum_tcpudp_magic(ip->saddr, ip->daddr,
+						length, ip->protocol, 0);
+		skb->data[insert] = 0;
+		skb->data[insert + 1] = 0;
+	}
+	cur_p->app0 |= STS_CTRL_APP0_SOP;
+	cur_p->len = skb_headlen(skb);
+	cur_p->phys = dma_map_single(ndev->dev.parent, skb->data, skb->len,
+				     DMA_TO_DEVICE);
+	cur_p->app4 = (unsigned long)skb;
+
+	for (ii = 0; ii < num_frag; ii++) {
+		lp->tx_bd_tail++;
+		if (lp->tx_bd_tail >= TX_BD_NUM)
+			lp->tx_bd_tail = 0;
+
+		cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
+		cur_p->phys = dma_map_single(ndev->dev.parent,
+					     (void *)page_address(frag->page) +
+					          frag->page_offset,
+					     frag->size, DMA_TO_DEVICE);
+		cur_p->len = frag->size;
+		cur_p->app0 = 0;
+		frag++;
+	}
+	cur_p->app0 |= STS_CTRL_APP0_EOP;
+
+	tail_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
+	lp->tx_bd_tail++;
+	if (lp->tx_bd_tail >= TX_BD_NUM)
+		lp->tx_bd_tail = 0;
+
+	/* Kick off the transfer */
+	temac_dma_out32(lp, TX_TAILDESC_PTR, tail_p); /* DMA start */
+
+	return 0;
+}
+
+
+static void ll_temac_recv(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	struct sk_buff *skb, *new_skb;
+	unsigned int bdstat;
+	struct cdmac_bd *cur_p;
+	dma_addr_t tail_p;
+	int length;
+	unsigned long skb_vaddr;
+	unsigned long flags;
+
+	spin_lock_irqsave(&lp->rx_lock, flags);
+
+	tail_p = lp->rx_bd_p + sizeof(*lp->rx_bd_v) * lp->rx_bd_ci;
+	cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
+
+	bdstat = cur_p->app0;
+	while ((bdstat & STS_CTRL_APP0_CMPLT)) {
+
+		skb = lp->rx_skb[lp->rx_bd_ci];
+		length = cur_p->app4;
+
+		skb_vaddr = virt_to_bus(skb->data);
+		dma_unmap_single(ndev->dev.parent, skb_vaddr, length,
+				 DMA_FROM_DEVICE);
+
+		skb_put(skb, length);
+		skb->dev = ndev;
+		skb->protocol = eth_type_trans(skb, ndev);
+		skb->ip_summed = CHECKSUM_NONE;
+
+		netif_rx(skb);
+
+		ndev->stats.rx_packets++;
+		ndev->stats.rx_bytes += length;
+
+		new_skb = alloc_skb(XTE_MAX_JUMBO_FRAME_SIZE + XTE_ALIGN,
+				GFP_ATOMIC);
+		if (new_skb == 0) {
+			dev_err(&ndev->dev, "no memory for new sk_buff\n");
+			spin_unlock_irqrestore(&lp->rx_lock, flags);
+			return;
+		}
+
+		skb_reserve(new_skb, BUFFER_ALIGN(new_skb->data));
+
+		cur_p->app0 = STS_CTRL_APP0_IRQONEND;
+		cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
+					     XTE_MAX_JUMBO_FRAME_SIZE,
+					     DMA_FROM_DEVICE);
+		cur_p->len = XTE_MAX_JUMBO_FRAME_SIZE;
+		lp->rx_skb[lp->rx_bd_ci] = new_skb;
+
+		lp->rx_bd_ci++;
+		if (lp->rx_bd_ci >= RX_BD_NUM)
+			lp->rx_bd_ci = 0;
+
+		cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
+		bdstat = cur_p->app0;
+	}
+	temac_dma_out32(lp, RX_TAILDESC_PTR, tail_p);
+
+	spin_unlock_irqrestore(&lp->rx_lock, flags);
+}
+
+static irqreturn_t ll_temac_tx_irq(int irq, void *_ndev)
+{
+	struct net_device *ndev = _ndev;
+	struct temac_local *lp = netdev_priv(ndev);
+	unsigned int status;
+
+	status = temac_dma_in32(lp, TX_IRQ_REG);
+	temac_dma_out32(lp, TX_IRQ_REG, status);
+
+	if (status & (IRQ_COAL | IRQ_DLY))
+		temac_start_xmit_done(lp->ndev);
+	if (status & 0x080)
+		dev_err(&ndev->dev, "DMA error 0x%x\n", status);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t ll_temac_rx_irq(int irq, void *_ndev)
+{
+	struct net_device *ndev = _ndev;
+	struct temac_local *lp = netdev_priv(ndev);
+	unsigned int status;
+
+	/* Read and clear the status registers */
+	status = temac_dma_in32(lp, RX_IRQ_REG);
+	temac_dma_out32(lp, RX_IRQ_REG, status);
+
+	if (status & (IRQ_COAL | IRQ_DLY))
+		ll_temac_recv(lp->ndev);
+
+	return IRQ_HANDLED;
+}
+
+static int temac_open(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+	int rc;
+
+	dev_dbg(&ndev->dev, "temac_open()\n");
+
+	if (lp->phy_node) {
+		lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node,
+					     temac_adjust_link, 0, 0);
+		if (!lp->phy_dev) {
+			dev_err(lp->dev, "of_phy_connect() failed\n");
+			return -ENODEV;
+		}
+
+		phy_start(lp->phy_dev);
+	}
+
+	rc = request_irq(lp->tx_irq, ll_temac_tx_irq, 0, ndev->name, ndev);
+	if (rc)
+		goto err_tx_irq;
+	rc = request_irq(lp->rx_irq, ll_temac_rx_irq, 0, ndev->name, ndev);
+	if (rc)
+		goto err_rx_irq;
+
+	temac_device_reset(ndev);
+	return 0;
+
+ err_rx_irq:
+	free_irq(lp->tx_irq, ndev);
+ err_tx_irq:
+	if (lp->phy_dev)
+		phy_disconnect(lp->phy_dev);
+	lp->phy_dev = NULL;
+	dev_err(lp->dev, "request_irq() failed\n");
+	return rc;
+}
+
+static int temac_stop(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+
+	dev_dbg(&ndev->dev, "temac_close()\n");
+
+	free_irq(lp->tx_irq, ndev);
+	free_irq(lp->rx_irq, ndev);
+
+	if (lp->phy_dev)
+		phy_disconnect(lp->phy_dev);
+	lp->phy_dev = NULL;
+
+	return 0;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void
+temac_poll_controller(struct net_device *ndev)
+{
+	struct temac_local *lp = netdev_priv(ndev);
+
+	disable_irq(lp->tx_irq);
+	disable_irq(lp->rx_irq);
+
+	ll_temac_rx_irq(lp->tx_irq, lp);
+	ll_temac_tx_irq(lp->rx_irq, lp);
+
+	enable_irq(lp->tx_irq);
+	enable_irq(lp->rx_irq);
+}
+#endif
+
+static const struct net_device_ops temac_netdev_ops = {
+	.ndo_open = temac_open,
+	.ndo_stop = temac_stop,
+	.ndo_start_xmit = temac_start_xmit,
+	.ndo_set_mac_address = temac_set_mac_address,
+	//.ndo_set_multicast_list = temac_set_multicast_list,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	.ndo_poll_controller = temac_poll_controller,
+#endif
+};
+
+/* ---------------------------------------------------------------------
+ * SYSFS device attributes
+ */
+static ssize_t temac_show_llink_regs(struct device *dev,
+				     struct device_attribute *attr, char *buf)
+{
+	struct net_device *ndev = dev_get_drvdata(dev);
+	struct temac_local *lp = netdev_priv(ndev);
+	int i, len = 0;
+
+	for (i = 0; i < 0x11; i++)
+		len += sprintf(buf + len, "%.8x%s", temac_dma_in32(lp, i),
+			       (i % 8) == 7 ? "\n" : " ");
+	len += sprintf(buf + len, "\n");
+
+	return len;
+}
+
+static DEVICE_ATTR(llink_regs, 0440, temac_show_llink_regs, NULL);
+
+static struct attribute *temac_device_attrs[] = {
+	&dev_attr_llink_regs.attr,
+	NULL,
+};
+
+static const struct attribute_group temac_attr_group = {
+	.attrs = temac_device_attrs,
+};
+
+static int __init
+temac_of_probe(struct of_device *op, const struct of_device_id *match)
+{
+	struct device_node *np;
+	struct temac_local *lp;
+	struct net_device *ndev;
+	const void *addr;
+	int size, rc = 0;
+	unsigned int dcrs;
+
+	/* Init network device structure */
+	ndev = alloc_etherdev(sizeof(*lp));
+	if (!ndev) {
+		dev_err(&op->dev, "could not allocate device.\n");
+		return -ENOMEM;
+	}
+	ether_setup(ndev);
+	dev_set_drvdata(&op->dev, ndev);
+	SET_NETDEV_DEV(ndev, &op->dev);
+	ndev->flags &= ~IFF_MULTICAST;  /* clear multicast */
+	ndev->features = NETIF_F_SG | NETIF_F_FRAGLIST;
+	ndev->netdev_ops = &temac_netdev_ops;
+#if 0
+	ndev->features |= NETIF_F_IP_CSUM; /* Can checksum TCP/UDP over IPv4. */
+	ndev->features |= NETIF_F_HW_CSUM; /* Can checksum all the packets. */
+	ndev->features |= NETIF_F_IPV6_CSUM; /* Can checksum IPV6 TCP/UDP */
+	ndev->features |= NETIF_F_HIGHDMA; /* Can DMA to high memory. */
+	ndev->features |= NETIF_F_HW_VLAN_TX; /* Transmit VLAN hw accel */
+	ndev->features |= NETIF_F_HW_VLAN_RX; /* Receive VLAN hw acceleration */
+	ndev->features |= NETIF_F_HW_VLAN_FILTER; /* Receive VLAN filtering */
+	ndev->features |= NETIF_F_VLAN_CHALLENGED; /* cannot handle VLAN pkts */
+	ndev->features |= NETIF_F_GSO; /* Enable software GSO. */
+	ndev->features |= NETIF_F_MULTI_QUEUE; /* Has multiple TX/RX queues */
+	ndev->features |= NETIF_F_LRO; /* large receive offload */
+#endif
+
+	/* setup temac private info structure */
+	lp = netdev_priv(ndev);
+	lp->ndev = ndev;
+	lp->dev = &op->dev;
+	lp->options = XTE_OPTION_DEFAULTS;
+	spin_lock_init(&lp->rx_lock);
+	mutex_init(&lp->indirect_mutex);
+
+	/* map device registers */
+	lp->regs = of_iomap(op->node, 0);
+	if (!lp->regs) {
+		dev_err(&op->dev, "could not map temac regs.\n");
+		goto nodev;
+	}
+
+	/* Find the DMA node, map the DMA registers, and decode the DMA IRQs */
+	np = of_parse_phandle(op->node, "llink-connected", 0);
+	if (!np) {
+		dev_err(&op->dev, "could not find DMA node\n");
+		goto nodev;
+	}
+
+	dcrs = dcr_resource_start(np, 0);
+	if (dcrs == 0) {
+		dev_err(&op->dev, "could not get DMA register address\n");
+		goto nodev;;
+	}
+	lp->sdma_dcrs = dcr_map(np, dcrs, dcr_resource_len(np, 0));
+	dev_dbg(&op->dev, "DCR base: %x\n", dcrs);
+
+	lp->rx_irq = irq_of_parse_and_map(np, 0);
+	lp->tx_irq = irq_of_parse_and_map(np, 1);
+	if (!lp->rx_irq || !lp->tx_irq) {
+		dev_err(&op->dev, "could not determine irqs\n");
+		rc = -ENOMEM;
+		goto nodev;
+	}
+
+	of_node_put(np); /* Finished with the DMA node; drop the reference */
+
+	/* Retrieve the MAC address */
+	addr = of_get_property(op->node, "local-mac-address", &size);
+	if ((!addr) || (size != 6)) {
+		dev_err(&op->dev, "could not find MAC address\n");
+		rc = -ENODEV;
+		goto nodev;
+	}
+	temac_set_mac_address(ndev, (void *)addr);
+
+	rc = temac_mdio_setup(lp, op->node);
+	if (rc)
+		dev_warn(&op->dev, "error registering MDIO bus\n");
+
+	lp->phy_node = of_parse_phandle(op->node, "phy-handle", 0);
+	if (lp->phy_node)
+		dev_dbg(lp->dev, "using PHY node %s (%p)\n", np->full_name, np);
+
+	/* Add the device attributes */
+	rc = sysfs_create_group(&lp->dev->kobj, &temac_attr_group);
+	if (rc) {
+		dev_err(lp->dev, "Error creating sysfs files\n");
+		goto nodev;
+	}
+
+	rc = register_netdev(lp->ndev);
+	if (rc) {
+		dev_err(lp->dev, "register_netdev() error (%i)\n", rc);
+		goto err_register_ndev;
+	}
+
+	return 0;
+
+ err_register_ndev:
+	sysfs_remove_group(&lp->dev->kobj, &temac_attr_group);
+ nodev:
+	free_netdev(ndev);
+	ndev = NULL;
+	return rc;
+}
+
+static int __devexit temac_of_remove(struct of_device *op)
+{
+	struct net_device *ndev = dev_get_drvdata(&op->dev);
+	struct temac_local *lp = netdev_priv(ndev);
+
+	temac_mdio_teardown(lp);
+	unregister_netdev(ndev);
+	sysfs_remove_group(&lp->dev->kobj, &temac_attr_group);
+	if (lp->phy_node)
+		of_node_put(lp->phy_node);
+	lp->phy_node = NULL;
+	dev_set_drvdata(&op->dev, NULL);
+	free_netdev(ndev);
+	return 0;
+}
+
+static struct of_device_id temac_of_match[] __devinitdata = {
+	{ .compatible = "xlnx,xps-ll-temac-1.01.b", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, temac_of_match);
+
+static struct of_platform_driver temac_of_driver = {
+	.match_table = temac_of_match,
+	.probe = temac_of_probe,
+	.remove = __devexit_p(temac_of_remove),
+	.driver = {
+		.owner = THIS_MODULE,
+		.name = "xilinx_temac",
+	},
+};
+
+static int __init temac_init(void)
+{
+	return of_register_platform_driver(&temac_of_driver);
+}
+module_init(temac_init);
+
+static void __exit temac_exit(void)
+{
+	of_unregister_platform_driver(&temac_of_driver);
+}
+module_exit(temac_exit);
+
+MODULE_DESCRIPTION("Xilinx LL_TEMAC Ethernet driver");
+MODULE_AUTHOR("Yoshio Kashiwagi");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ll_temac_mdio.c b/drivers/net/ll_temac_mdio.c
new file mode 100644
index 0000000..da0e462
--- /dev/null
+++ b/drivers/net/ll_temac_mdio.c
@@ -0,0 +1,120 @@
+/*
+ * MDIO bus driver for the Xilinx TEMAC device
+ *
+ * Copyright (c) 2009 Secret Lab Technologies, Ltd.
+ */
+
+#include <linux/io.h>
+#include <linux/netdevice.h>
+#include <linux/mutex.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_mdio.h>
+
+#include "ll_temac.h"
+
+/* ---------------------------------------------------------------------
+ * MDIO Bus functions
+ */
+static int temac_mdio_read(struct mii_bus *bus, int phy_id, int reg)
+{
+	struct temac_local *lp = bus->priv;
+	u32 rc;
+
+	/* Write the PHY address to the MIIM Access Initiator register.
+	 * When the transfer completes, the PHY register value will appear
+	 * in the LSW0 register */
+	mutex_lock(&lp->indirect_mutex);
+	temac_iow(lp, XTE_LSW0_OFFSET, (phy_id << 5) | reg);
+	rc = temac_indirect_in32(lp, XTE_MIIMAI_OFFSET);
+	mutex_unlock(&lp->indirect_mutex);
+
+	dev_dbg(lp->dev, "temac_mdio_read(phy_id=%i, reg=%x) == %x\n",
+		phy_id, reg, rc);
+
+	return rc;
+}
+
+static int temac_mdio_write(struct mii_bus *bus, int phy_id, int reg, u16 val)
+{
+	struct temac_local *lp = bus->priv;
+
+	dev_dbg(lp->dev, "temac_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
+		phy_id, reg, val);
+
+	/* First write the desired value into the write data register
+	 * and then write the address into the access initiator register
+	 */
+	mutex_lock(&lp->indirect_mutex);
+	temac_indirect_out32(lp, XTE_MGTDR_OFFSET, val);
+	temac_indirect_out32(lp, XTE_MIIMAI_OFFSET, (phy_id << 5) | reg);
+	mutex_unlock(&lp->indirect_mutex);
+
+	return 0;
+}
+
+int temac_mdio_setup(struct temac_local *lp, struct device_node *np)
+{
+	struct mii_bus *bus;
+	const u32 *bus_hz;
+	int clk_div;
+	int rc, size;
+	struct resource res;
+
+	/* Calculate a reasonable divisor for the clock rate */
+	clk_div = 0x3f; /* worst-case default setting */
+	bus_hz = of_get_property(np, "clock-frequency", &size);
+	if (bus_hz && size >= sizeof(*bus_hz)) {
+		clk_div = (*bus_hz) / (2500 * 1000 * 2) - 1;
+		if (clk_div < 1)
+			clk_div = 1;
+		if (clk_div > 0x3f)
+			clk_div = 0x3f;
+	}
+
+	/* Enable the MDIO bus by asserting the enable bit and writing
+	 * in the clock config */
+	mutex_lock(&lp->indirect_mutex);
+	temac_indirect_out32(lp, XTE_MC_OFFSET, 1 << 6 | clk_div);
+	mutex_unlock(&lp->indirect_mutex);
+
+	bus = mdiobus_alloc();
+	if (!bus)
+		return -ENOMEM;
+
+	of_address_to_resource(np, 0, &res);
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%.8llx",
+		 (unsigned long long)res.start);
+	bus->priv = lp;
+	bus->name = "Xilinx TEMAC MDIO";
+	bus->read = temac_mdio_read;
+	bus->write = temac_mdio_write;
+	bus->parent = lp->dev;
+	bus->irq = lp->mdio_irqs; /* preallocated IRQ table */
+
+	lp->mii_bus = bus;
+
+	rc = of_mdiobus_register(bus, np);
+	if (rc)
+		goto err_register;
+
+	mutex_lock(&lp->indirect_mutex);
+	dev_dbg(lp->dev, "MDIO bus registered;  MC:%x\n",
+		temac_indirect_in32(lp, XTE_MC_OFFSET));
+	mutex_unlock(&lp->indirect_mutex);
+	return 0;
+
+ err_register:
+	mdiobus_free(bus);
+	return rc;
+}
+
+void temac_mdio_teardown(struct temac_local *lp)
+{
+	mdiobus_unregister(lp->mii_bus);
+	kfree(lp->mii_bus->irq);
+	mdiobus_free(lp->mii_bus);
+	lp->mii_bus = NULL;
+}
+