serial: sh-sci: Add support for SCIFA/SCIFB variable sampling rates
Add support for sparse variable sampling rates on SCIFA and SCIFB.
According to the datasheet, sampling rate 1/5 needs a small quirk to
avoid corrupting the first byte received.
This increases the range and accuracy of supported baud rates.
E.g. on r8a7791/koelsch:
- Supports now 134, 150, and standard 500000-4000000 bps,
- Perfect match for 134, 150, 500000, 1000000, 2000000, and 4000000
bps,
- Accuracy has increased for most standard bps values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index dbf488b..4678d8f 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -88,6 +88,10 @@
#define SCI_SR(x) BIT((x) - 1)
#define SCI_SR_RANGE(x, y) GENMASK((y) - 1, (x) - 1)
+#define SCI_SR_SCIFAB SCI_SR(5) | SCI_SR(7) | SCI_SR(11) | \
+ SCI_SR(13) | SCI_SR(16) | SCI_SR(17) | \
+ SCI_SR(19) | SCI_SR(27)
+
#define min_sr(_port) ffs((_port)->sampling_rate_mask)
#define max_sr(_port) fls((_port)->sampling_rate_mask)
@@ -2179,6 +2183,17 @@
uart_update_timeout(port, termios->c_cflag, baud);
if (best_clk >= 0) {
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
+ switch (srr + 1) {
+ case 5: smr_val |= SCSMR_SRC_5; break;
+ case 7: smr_val |= SCSMR_SRC_7; break;
+ case 11: smr_val |= SCSMR_SRC_11; break;
+ case 13: smr_val |= SCSMR_SRC_13; break;
+ case 16: smr_val |= SCSMR_SRC_16; break;
+ case 17: smr_val |= SCSMR_SRC_17; break;
+ case 19: smr_val |= SCSMR_SRC_19; break;
+ case 27: smr_val |= SCSMR_SRC_27; break;
+ }
smr_val |= cks;
dev_dbg(port->dev,
"SCR 0x%x SMR 0x%x BRR %u CKS 0x%x DL %u SRR %u\n",
@@ -2227,6 +2242,16 @@
scr_val |= s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0);
dev_dbg(port->dev, "SCSCR 0x%x\n", scr_val);
serial_port_out(port, SCSCR, scr_val);
+ if ((srr + 1 == 5) &&
+ (port->type == PORT_SCIFA || port->type == PORT_SCIFB)) {
+ /*
+ * In asynchronous mode, when the sampling rate is 1/5, first
+ * received data may become invalid on some SCIFA and SCIFB.
+ * To avoid this problem wait more than 1 serial data time (1
+ * bit time x serial data number) after setting SCSCR.RE = 1.
+ */
+ udelay(DIV_ROUND_UP(10 * 1000000, baud));
+ }
#ifdef CONFIG_SERIAL_SH_SCI_DMA
/*
@@ -2523,7 +2548,7 @@
port->fifosize = 256;
sci_port->overrun_reg = SCxSR;
sci_port->overrun_mask = SCIFA_ORER;
- sci_port->sampling_rate_mask = SCI_SR(16);
+ sci_port->sampling_rate_mask = SCI_SR_SCIFAB;
break;
case PORT_HSCIF:
port->fifosize = 128;
@@ -2535,7 +2560,7 @@
port->fifosize = 64;
sci_port->overrun_reg = SCxSR;
sci_port->overrun_mask = SCIFA_ORER;
- sci_port->sampling_rate_mask = SCI_SR(16);
+ sci_port->sampling_rate_mask = SCI_SR_SCIFAB;
break;
case PORT_SCIF:
port->fifosize = 16;