ibft: Fix finding IBFT ACPI table on UEFI
Found one system with UEFI/iBFT, kernel does not detect the iBFT during
iscsi_ibft module loading.
Root cause: on x86 (UEFI), we are calling of find_ibft_region() much earlier
- specifically in setup_arch() before ACPI is enabled.
Try to split acpi checking code out and call that later
At that time ACPI iBFT already get permanent mapped with ioremap.
So isa_virt_to_bus() will get wrong phys from right virt address.
We could just skip that phys address printing.
For legacy one, print the found address early.
-v2: update comments and description according to Konrad.
-v3: fix problem about module use case that is found by Konrad.
-v4: use acpi_get_table() instead of acpi_table_parse() to handle module use case that is found by Konrad again..
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
diff --git a/drivers/firmware/iscsi_ibft.c b/drivers/firmware/iscsi_ibft.c
index c811cb1..2cce44a 100644
--- a/drivers/firmware/iscsi_ibft.c
+++ b/drivers/firmware/iscsi_ibft.c
@@ -746,6 +746,37 @@
ibft_cleanup();
}
+#ifdef CONFIG_ACPI
+static const struct {
+ char *sign;
+} ibft_signs[] = {
+ /*
+ * One spec says "IBFT", the other says "iBFT". We have to check
+ * for both.
+ */
+ { ACPI_SIG_IBFT },
+ { "iBFT" },
+};
+
+static void __init acpi_find_ibft_region(void)
+{
+ int i;
+ struct acpi_table_header *table = NULL;
+
+ if (acpi_disabled)
+ return;
+
+ for (i = 0; i < ARRAY_SIZE(ibft_signs) && !ibft_addr; i++) {
+ acpi_get_table(ibft_signs[i].sign, 0, &table);
+ ibft_addr = (struct acpi_table_ibft *)table;
+ }
+}
+#else
+static void __init acpi_find_ibft_region(void)
+{
+}
+#endif
+
/*
* ibft_init() - creates sysfs tree entries for the iBFT data.
*/
@@ -753,9 +784,16 @@
{
int rc = 0;
+ /*
+ As on UEFI systems the setup_arch()/find_ibft_region()
+ is called before ACPI tables are parsed and it only does
+ legacy finding.
+ */
+ if (!ibft_addr)
+ acpi_find_ibft_region();
+
if (ibft_addr) {
- printk(KERN_INFO "iBFT detected at 0x%llx.\n",
- (u64)isa_virt_to_bus(ibft_addr));
+ pr_info("iBFT detected.\n");
rc = ibft_check_device();
if (rc)
diff --git a/drivers/firmware/iscsi_ibft_find.c b/drivers/firmware/iscsi_ibft_find.c
index bfe7232..4da4eb9 100644
--- a/drivers/firmware/iscsi_ibft_find.c
+++ b/drivers/firmware/iscsi_ibft_find.c
@@ -45,13 +45,6 @@
static const struct {
char *sign;
} ibft_signs[] = {
-#ifdef CONFIG_ACPI
- /*
- * One spec says "IBFT", the other says "iBFT". We have to check
- * for both.
- */
- { ACPI_SIG_IBFT },
-#endif
{ "iBFT" },
{ "BIFT" }, /* Broadcom iSCSI Offload */
};
@@ -62,14 +55,6 @@
#define VGA_MEM 0xA0000 /* VGA buffer */
#define VGA_SIZE 0x20000 /* 128kB */
-#ifdef CONFIG_ACPI
-static int __init acpi_find_ibft(struct acpi_table_header *header)
-{
- ibft_addr = (struct acpi_table_ibft *)header;
- return 0;
-}
-#endif /* CONFIG_ACPI */
-
static int __init find_ibft_in_mem(void)
{
unsigned long pos;
@@ -94,6 +79,7 @@
* the table cannot be valid. */
if (pos + len <= (IBFT_END-1)) {
ibft_addr = (struct acpi_table_ibft *)virt;
+ pr_info("iBFT found at 0x%lx.\n", pos);
goto done;
}
}
@@ -108,20 +94,12 @@
*/
unsigned long __init find_ibft_region(unsigned long *sizep)
{
-#ifdef CONFIG_ACPI
- int i;
-#endif
ibft_addr = NULL;
-#ifdef CONFIG_ACPI
- for (i = 0; i < ARRAY_SIZE(ibft_signs) && !ibft_addr; i++)
- acpi_table_parse(ibft_signs[i].sign, acpi_find_ibft);
-#endif /* CONFIG_ACPI */
-
/* iBFT 1.03 section 1.4.3.1 mandates that UEFI machines will
* only use ACPI for this */
- if (!ibft_addr && !efi_enabled)
+ if (!efi_enabled)
find_ibft_in_mem();
if (ibft_addr) {