Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
First batch of DT changes for 4.5:
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time
ARM: at91/dt: sama5d4: update i2c compatible string
ARM: at91/dt: sama5d4 master clock can run at 200MHz now
ARM: at91/dt: sama5d2: add watchdog node
ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK
ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus
ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index be599a3..39aed91 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@
sama5d34ek.dtb \
sama5d35ek.dtb \
sama5d36ek.dtb \
+ at91-sama5d4_ma5d4evk.dtb \
at91-sama5d4_xplained.dtb \
at91-sama5d4ek.dtb
dtb-$(CONFIG_ARCH_ATLAS6) += \
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index ad6de73..80fdab7 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -129,6 +129,7 @@
dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ i2c-sda-hold-time-ns = <350>;
status = "okay";
pmic: act8865@5b {
@@ -206,6 +207,10 @@
};
};
+ watchdog@f8048040 {
+ status = "okay";
+ };
+
uart3: serial@fc008000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3_default>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
new file mode 100644
index 0000000..e7b2109
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "sama5d4.dtsi"
+
+/ {
+ model = "DENX MA5D4";
+ compatible = "denx,ma5d4", "atmel,sama5d4", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x10000000>;
+ };
+
+ clocks {
+ main_clock: main_clock {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+
+ clk20m: clk20m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <20000000>;
+ clock-output-names = "clk20m";
+ };
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7>;
+ vmmc-supply = <&vcc_mmc0_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ broken-cd;
+ };
+ };
+
+ spi0: spi@f8010000 {
+ cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+ status = "okay";
+
+ m25p80@0 {
+ compatible = "atmel,at25df321a";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ i2c0: i2c@f8014000 {
+ status = "okay";
+ };
+
+ spi1: spi@fc018000 {
+ cs-gpios = <&pioB 22 0>, <&pioB 23 0>, <0>, <0>;
+ status = "okay";
+
+ can0: can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ clocks = <&clk20m>;
+ interrupt-parent = <&pioE>;
+ interrupts = <6 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <10000000>;
+ };
+
+ can1: can@1 {
+ compatible = "microchip,mcp2515";
+ reg = <1>;
+ clocks = <&clk20m>;
+ interrupt-parent = <&pioE>;
+ interrupts = <7 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <10000000>;
+ };
+ };
+
+ adc0: adc@fc034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ /* external trigger conflicts with USBA_VBUS */
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ atmel,adc-vref = <3300>;
+ status = "okay";
+ };
+
+ watchdog@fc068640 {
+ status = "okay";
+ };
+ };
+ };
+
+ vcc_3v3_reg: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC 3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_mmc0_reg: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ gpio = <&pioE 15 GPIO_ACTIVE_HIGH>;
+ regulator-name = "RST_n MCI0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_reg>;
+ regulator-boot-on;
+ };
+};
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts b/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts
new file mode 100644
index 0000000..abaaba5
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts
@@ -0,0 +1,170 @@
+/*
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "at91-sama5d4_ma5d4.dtsi"
+
+/ {
+ model = "DENX MA5D4EVK";
+ compatible = "denx,ma5d4evk", "atmel,sama5d4", "atmel,sama5";
+
+ chosen {
+ stdout-path = "serial3:115200n8";
+ };
+
+ ahb {
+ usb0: gadget@00400000 {
+ atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci@00500000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioE 11 GPIO_ACTIVE_LOW
+ &pioE 14 GPIO_ACTIVE_LOW
+ >;
+ status = "okay";
+ };
+
+ usb2: ehci@00600000 {
+ status = "okay";
+ };
+
+ apb {
+ hlcdc: hlcdc@f0000000 {
+ status = "okay";
+
+ hlcdc-display-controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+
+ port@0 {
+ hlcdc_panel_output: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+ };
+ };
+
+ };
+
+ macb0: ethernet@f8020000 {
+ phy-mode = "rmii";
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
+ usart0: serial@f802c000 {
+ status = "okay";
+ };
+
+ usart1: serial@f8030000 {
+ status = "okay";
+ };
+
+ mmc1: mmc@fc000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ vmmc-supply = <&vcc_mmc1_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 5 0>;
+ };
+ };
+
+ adc0: adc@fc034000 {
+ atmel,adc-ts-wires = <4>;
+ atmel,adc-ts-pressure-threshold = <10000>;
+ };
+
+
+ pinctrl@fc06a000 {
+ board {
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins = <AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&hlcdc_pwm 0 50000 0>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ user1 {
+ label = "user1";
+ gpios = <&pioD 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ user2 {
+ label = "user2";
+ gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ user3 {
+ label = "user3";
+ gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel: panel {
+ /* Actually Ampire 800480R2 */
+ compatible = "foxlink,fl500wvr00-a0t", "simple-panel";
+ backlight = <&backlight>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&hlcdc_panel_output>;
+ };
+ };
+ };
+
+ vcc_mmc1_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ gpio = <&pioE 17 GPIO_ACTIVE_LOW>;
+ regulator-name = "VDD MCI1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_reg>;
+ };
+};
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 4dfca8f..545264b 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -929,6 +929,13 @@
clocks = <&h32ck>;
};
+ watchdog@f8048040 {
+ compatible = "atmel,sama5d4-wdt";
+ reg = <0xf8048040 0x10>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 7>;
+ status = "disabled";
+ };
+
sckc@f8048050 {
compatible = "atmel,at91sam9x5-sckc";
reg = <0xf8048050 0x4>;
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index 2193637..b8032bc 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -451,7 +451,7 @@
interrupt-parent = <&pmc>;
interrupts = <AT91_PMC_MCKRDY>;
clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
- atmel,clk-output-range = <125000000 177000000>;
+ atmel,clk-output-range = <125000000 200000000>;
atmel,clk-divisors = <1 2 4 3>;
};
@@ -916,7 +916,7 @@
};
i2c0: i2c@f8014000 {
- compatible = "atmel,at91sam9x5-i2c";
+ compatible = "atmel,sama5d4-i2c";
reg = <0xf8014000 0x4000>;
interrupts = <32 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma1
@@ -935,7 +935,7 @@
};
i2c1: i2c@f8018000 {
- compatible = "atmel,at91sam9x5-i2c";
+ compatible = "atmel,sama5d4-i2c";
reg = <0xf8018000 0x4000>;
interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma1
@@ -975,7 +975,7 @@
};
i2c2: i2c@f8024000 {
- compatible = "atmel,at91sam9x5-i2c";
+ compatible = "atmel,sama5d4-i2c";
reg = <0xf8024000 0x4000>;
interrupts = <34 IRQ_TYPE_LEVEL_HIGH 6>;
dmas = <&dma1
@@ -1669,15 +1669,23 @@
pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 {
atmel,pins =
<AT91_PIOC 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* MCI0_CK, conflict with PCK1(ISI_MCK) */
- AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_CDB, conflict with NAND_D0 */
- AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DB0, conflict with NAND_D1 */
+ AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_CDA, conflict with NAND_D0 */
+ AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA0, conflict with NAND_D1 */
>;
};
pinctrl_mmc0_dat1_3: mmc0_dat1_3 {
atmel,pins =
- <AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DB1, conflict with NAND_D2 */
- AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DB2, conflict with NAND_D3 */
- AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DB3, conflict with NAND_D4 */
+ <AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA1, conflict with NAND_D2 */
+ AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA2, conflict with NAND_D3 */
+ AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA3, conflict with NAND_D4 */
+ >;
+ };
+ pinctrl_mmc0_dat4_7: mmc0_dat4_7 {
+ atmel,pins =
+ <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA4, conflict with NAND_D5 */
+ AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA5, conflict with NAND_D6 */
+ AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA6, conflict with NAND_D7 */
+ AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* MCI0_DA7, conflict with NAND_OE */
>;
};
};