Merge tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.10, 2nd round:
- A couple of Nitrogen6 device tree fixes for audio codec probe
failure, which is caused by that pinctrl setting for codec clock
was not in the correct device node.
* tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt
index 3e5b979..8682ab6 100644
--- a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt
+++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt
@@ -8,8 +8,9 @@
Required properties:
- compatible: should be "ti,tps65217-pwrbutton" or "ti,tps65218-pwrbutton"
-Required properties for TPS65218:
+Required properties:
- interrupts: should be one of the following
+ - <2>: For controllers compatible with tps65217
- <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218
Examples:
@@ -17,6 +18,7 @@
&tps {
tps65217-pwrbutton {
compatible = "ti,tps65217-pwrbutton";
+ interrupts = <2>;
};
};
diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt
index 98d131a..a11072c 100644
--- a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt
+++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt
@@ -2,11 +2,16 @@
Required Properties:
-compatible: "ti,tps65217-charger"
+-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change.
+ Should be <0> for the USB charger and <1> for the AC adapter.
+-interrupt-names: Should be "USB" and "AC"
This node is a subnode of the tps65217 PMIC.
Example:
tps65217-charger {
- compatible = "ti,tps65090-charger";
+ compatible = "ti,tps65217-charger";
+ interrupts = <0>, <1>;
+ interrupt-names = "USB", "AC";
};
diff --git a/MAINTAINERS b/MAINTAINERS
index cfff2c9..c7397bd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9842,7 +9842,7 @@
M: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
L: linux-arm-kernel@lists.infradead.org
S: Maintained
-F: drivers/firmware/psci.c
+F: drivers/firmware/psci*.c
F: include/linux/psci.h
F: include/uapi/linux/psci.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5fab553..186c4c2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1502,8 +1502,7 @@
config HZ_FIXED
int
- default 200 if ARCH_EBSA110 || ARCH_S3C24XX || \
- ARCH_S5PV210 || ARCH_EXYNOS4
+ default 200 if ARCH_EBSA110
default 128 if SOC_AT91RM9200
default 0
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb..7327250 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -501,6 +501,7 @@
am3517-evm.dtb \
am3517_mt_ventoux.dtb \
logicpd-torpedo-37xx-devkit.dtb \
+ logicpd-som-lv-37xx-devkit.dtb \
omap3430-sdp.dtb \
omap3-beagle.dtb \
omap3-beagle-xm.dtb \
diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi
index dc561d5..3e32dd1 100644
--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
+++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
@@ -6,8 +6,6 @@
* published by the Free Software Foundation.
*/
-#include <dt-bindings/mfd/tps65217.h>
-
/ {
cpus {
cpu@0 {
@@ -319,13 +317,13 @@
ti,pmic-shutdown-controller;
charger {
- interrupts = <TPS65217_IRQ_AC>, <TPS65217_IRQ_USB>;
- interrupts-names = "AC", "USB";
+ interrupts = <0>, <1>;
+ interrupt-names = "USB", "AC";
status = "okay";
};
pwrbutton {
- interrupts = <TPS65217_IRQ_PB>;
+ interrupts = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 64c8aa9..18d72a2 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -16,6 +16,7 @@
interrupt-parent = <&intc>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
aliases {
i2c0 = &i2c0;
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index ac55f93..2df9e60 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -16,6 +16,7 @@
interrupt-parent = <&wakeupgen>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
memory@0 {
device_type = "memory";
diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index d6e43e5..ad68d1e 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -62,11 +62,6 @@
linux,default-trigger = "mmc0";
};
};
-
- extcon_usb2: extcon_usb2 {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
- };
};
&mmc1 {
@@ -79,3 +74,8 @@
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
+
+&extcon_usb2 {
+ id-gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+ vbus-gpio = <&gpio7 22 GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index 27d9149..8350b4b 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -23,11 +23,6 @@
reg = <0x0 0x80000000 0x0 0x80000000>;
};
- extcon_usb2: extcon_usb2 {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
- };
-
status-leds {
compatible = "gpio-leds";
cpu0-led {
@@ -76,6 +71,11 @@
extcon = <&extcon_usb2>;
};
+&extcon_usb2 {
+ id-gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+ vbus-gpio = <&gpio3 26 GPIO_ACTIVE_HIGH>;
+};
+
&mmc1 {
status = "okay";
vmmc-supply = <&v3_3d>;
@@ -87,3 +87,7 @@
&sn65hvs882 {
load-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
};
+
+&pcie1 {
+ gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi
index 555ae21..814a720 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi
@@ -303,6 +303,13 @@
gpio-controller;
#gpio-cells = <2>;
};
+
+ extcon_usb2: tps659038_usb {
+ compatible = "ti,palmas-usb-vid";
+ ti,enable-vbus-detection;
+ ti,enable-id-detection;
+ /* ID & VBUS GPIOs provided in board dts */
+ };
};
};
@@ -369,7 +376,7 @@
};
&usb2 {
- dr_mode = "otg";
+ dr_mode = "peripheral";
};
&mmc2 {
diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi
index 1facc5f..81b8cec 100644
--- a/arch/arm/boot/dts/dm814x.dtsi
+++ b/arch/arm/boot/dts/dm814x.dtsi
@@ -12,6 +12,7 @@
interrupt-parent = <&intc>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
aliases {
i2c0 = &i2c1;
diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index 61dd2f6..6db652a 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -12,6 +12,7 @@
interrupt-parent = <&intc>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
aliases {
i2c0 = &i2c1;
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index addb753..1faf24a 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -18,6 +18,7 @@
compatible = "ti,dra7xx";
interrupt-parent = <&crossbar_mpu>;
+ chosen { };
aliases {
i2c0 = &i2c1;
diff --git a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
index ee6dac4..e6df676 100644
--- a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
@@ -132,3 +132,19 @@
ti,palmas-long-press-seconds = <6>;
};
};
+
+&usb2_phy1 {
+ phy-supply = <&ldo4_reg>;
+};
+
+&usb2_phy2 {
+ phy-supply = <&ldo4_reg>;
+};
+
+&dss {
+ vdda_video-supply = <&ldo5_reg>;
+};
+
+&mmc1 {
+ vmmc_aux-supply = <&ldo1_reg>;
+};
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index 4f793a0..f1d6de8 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -17,6 +17,7 @@
interrupt-parent = <&intc>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
aliases {
serial0 = &uart1;
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 87ca50b..4d448f1 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -734,6 +734,8 @@
vmmc_aux-supply = <&vsim>;
bus-width = <8>;
non-removable;
+ no-sdio;
+ no-sd;
};
&mmc3 {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index ecf5eb5..a3ff493 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -17,6 +17,7 @@
interrupt-parent = <&intc>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
aliases {
i2c0 = &i2c1;
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 8087456..578c53f 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -15,6 +15,7 @@
interrupt-parent = <&wakeupgen>;
#address-cells = <1>;
#size-cells = <1>;
+ chosen { };
aliases {
i2c0 = &i2c1;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 968c67a..7cd92ba 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -17,6 +17,7 @@
compatible = "ti,omap5";
interrupt-parent = <&wakeupgen>;
+ chosen { };
aliases {
i2c0 = &i2c1;
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 268bd47..407a461 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -4,6 +4,7 @@
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -303,6 +304,9 @@
firmware {
scm {
compatible = "qcom,scm-apq8064";
+
+ clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
+ clock-names = "core";
};
};
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
index 5ae4ec5..c852b69 100644
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615.dtsi
@@ -357,7 +357,7 @@
};
amba {
- compatible = "arm,amba-bus";
+ compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts b/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
index 102838f..15f4fd3 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
+++ b/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
@@ -81,7 +81,7 @@
#address-cells = <0>;
interrupt-controller;
reg = <0 0x2c001000 0 0x1000>,
- <0 0x2c002000 0 0x1000>,
+ <0 0x2c002000 0 0x2000>,
<0 0x2c004000 0 0x2000>,
<0 0x2c006000 0 0x2000>;
interrupts = <1 9 0xf04>;
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
index 45d08cc..bd107c5 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
+++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
@@ -131,7 +131,7 @@
#address-cells = <0>;
interrupt-controller;
reg = <0 0x2c001000 0 0x1000>,
- <0 0x2c002000 0 0x1000>,
+ <0 0x2c002000 0 0x2000>,
<0 0x2c004000 0 0x2000>,
<0 0x2c006000 0 0x2000>;
interrupts = <1 9 0xf04>;
diff --git a/arch/arm/mach-davinci/clock.c b/arch/arm/mach-davinci/clock.c
index df42c93..f5dce9b 100644
--- a/arch/arm/mach-davinci/clock.c
+++ b/arch/arm/mach-davinci/clock.c
@@ -31,10 +31,10 @@
static DEFINE_MUTEX(clocks_mutex);
static DEFINE_SPINLOCK(clockfw_lock);
-static void __clk_enable(struct clk *clk)
+void davinci_clk_enable(struct clk *clk)
{
if (clk->parent)
- __clk_enable(clk->parent);
+ davinci_clk_enable(clk->parent);
if (clk->usecount++ == 0) {
if (clk->flags & CLK_PSC)
davinci_psc_config(clk->domain, clk->gpsc, clk->lpsc,
@@ -44,7 +44,7 @@
}
}
-static void __clk_disable(struct clk *clk)
+void davinci_clk_disable(struct clk *clk)
{
if (WARN_ON(clk->usecount == 0))
return;
@@ -56,7 +56,7 @@
clk->clk_disable(clk);
}
if (clk->parent)
- __clk_disable(clk->parent);
+ davinci_clk_disable(clk->parent);
}
int davinci_clk_reset(struct clk *clk, bool reset)
@@ -103,7 +103,7 @@
return -EINVAL;
spin_lock_irqsave(&clockfw_lock, flags);
- __clk_enable(clk);
+ davinci_clk_enable(clk);
spin_unlock_irqrestore(&clockfw_lock, flags);
return 0;
@@ -118,7 +118,7 @@
return;
spin_lock_irqsave(&clockfw_lock, flags);
- __clk_disable(clk);
+ davinci_clk_disable(clk);
spin_unlock_irqrestore(&clockfw_lock, flags);
}
EXPORT_SYMBOL(clk_disable);
diff --git a/arch/arm/mach-davinci/clock.h b/arch/arm/mach-davinci/clock.h
index e2a5437..fa2b837 100644
--- a/arch/arm/mach-davinci/clock.h
+++ b/arch/arm/mach-davinci/clock.h
@@ -132,6 +132,8 @@
int davinci_set_refclk_rate(unsigned long rate);
int davinci_simple_set_rate(struct clk *clk, unsigned long rate);
int davinci_clk_reset(struct clk *clk, bool reset);
+void davinci_clk_enable(struct clk *clk);
+void davinci_clk_disable(struct clk *clk);
extern struct platform_device davinci_wdt_device;
extern void davinci_watchdog_reset(struct platform_device *);
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index e770c97..1d873d1 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -319,6 +319,16 @@
.gpsc = 1,
};
+/*
+ * In order to avoid adding the emac_clk to the clock lookup table twice (and
+ * screwing up the linked list in the process) create a separate clock for
+ * mdio inheriting the rate from emac_clk.
+ */
+static struct clk mdio_clk = {
+ .name = "mdio",
+ .parent = &emac_clk,
+};
+
static struct clk mcasp_clk = {
.name = "mcasp",
.parent = &async3_clk,
@@ -367,6 +377,16 @@
.flags = ALWAYS_ENABLED,
};
+/*
+ * In order to avoid adding the aemif_clk to the clock lookup table twice (and
+ * screwing up the linked list in the process) create a separate clock for
+ * nand inheriting the rate from aemif_clk.
+ */
+static struct clk aemif_nand_clk = {
+ .name = "nand",
+ .parent = &aemif_clk,
+};
+
static struct clk usb11_clk = {
.name = "usb11",
.parent = &pll0_sysclk4,
@@ -529,7 +549,7 @@
CLK(NULL, "arm", &arm_clk),
CLK(NULL, "rmii", &rmii_clk),
CLK("davinci_emac.1", NULL, &emac_clk),
- CLK("davinci_mdio.0", "fck", &emac_clk),
+ CLK("davinci_mdio.0", "fck", &mdio_clk),
CLK("davinci-mcasp.0", NULL, &mcasp_clk),
CLK("davinci-mcbsp.0", NULL, &mcbsp0_clk),
CLK("davinci-mcbsp.1", NULL, &mcbsp1_clk),
@@ -537,7 +557,15 @@
CLK("da830-mmc.0", NULL, &mmcsd0_clk),
CLK("da830-mmc.1", NULL, &mmcsd1_clk),
CLK("ti-aemif", NULL, &aemif_clk),
- CLK(NULL, "aemif", &aemif_clk),
+ /*
+ * The only user of this clock is davinci_nand and it get's it through
+ * con_id. The nand node itself is created from within the aemif
+ * driver to guarantee that it's probed after the aemif timing
+ * parameters are configured. of_dev_auxdata is not accessible from
+ * the aemif driver and can't be passed to of_platform_populate(). For
+ * that reason we're leaving the dev_id here as NULL.
+ */
+ CLK(NULL, "aemif", &aemif_nand_clk),
CLK("ohci-da8xx", "usb11", &usb11_clk),
CLK("musb-da8xx", "usb20", &usb20_clk),
CLK("spi_davinci.0", NULL, &spi0_clk),
diff --git a/arch/arm/mach-davinci/usb-da8xx.c b/arch/arm/mach-davinci/usb-da8xx.c
index c6feecf..9a6af0b 100644
--- a/arch/arm/mach-davinci/usb-da8xx.c
+++ b/arch/arm/mach-davinci/usb-da8xx.c
@@ -22,6 +22,8 @@
#define DA8XX_USB0_BASE 0x01e00000
#define DA8XX_USB1_BASE 0x01e25000
+static struct clk *usb20_clk;
+
static struct platform_device da8xx_usb_phy = {
.name = "da8xx-usb-phy",
.id = -1,
@@ -158,26 +160,13 @@
static void usb20_phy_clk_enable(struct clk *clk)
{
- struct clk *usb20_clk;
- int err;
u32 val;
u32 timeout = 500000; /* 500 msec */
val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
- usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
- if (IS_ERR(usb20_clk)) {
- pr_err("could not get usb20 clk: %ld\n", PTR_ERR(usb20_clk));
- return;
- }
-
/* The USB 2.O PLL requires that the USB 2.O PSC is enabled as well. */
- err = clk_prepare_enable(usb20_clk);
- if (err) {
- pr_err("failed to enable usb20 clk: %d\n", err);
- clk_put(usb20_clk);
- return;
- }
+ davinci_clk_enable(usb20_clk);
/*
* Turn on the USB 2.0 PHY, but just the PLL, and not OTG. The USB 1.1
@@ -197,8 +186,7 @@
pr_err("Timeout waiting for USB 2.0 PHY clock good\n");
done:
- clk_disable_unprepare(usb20_clk);
- clk_put(usb20_clk);
+ davinci_clk_disable(usb20_clk);
}
static void usb20_phy_clk_disable(struct clk *clk)
@@ -285,11 +273,19 @@
int __init da8xx_register_usb20_phy_clk(bool use_usb_refclkin)
{
struct clk *parent;
- int ret = 0;
+ int ret;
+
+ usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
+ ret = PTR_ERR_OR_ZERO(usb20_clk);
+ if (ret)
+ return ret;
parent = clk_get(NULL, use_usb_refclkin ? "usb_refclkin" : "pll0_aux");
- if (IS_ERR(parent))
- return PTR_ERR(parent);
+ ret = PTR_ERR_OR_ZERO(parent);
+ if (ret) {
+ clk_put(usb20_clk);
+ return ret;
+ }
usb20_phy_clk.parent = parent;
ret = clk_register(&usb20_phy_clk);
diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c
index 98ffe1e..a5d6841 100644
--- a/arch/arm/mach-exynos/platsmp.c
+++ b/arch/arm/mach-exynos/platsmp.c
@@ -385,36 +385,6 @@
return pen_release != -1 ? ret : 0;
}
-/*
- * Initialise the CPU possible map early - this describes the CPUs
- * which may be present or become present in the system.
- */
-
-static void __init exynos_smp_init_cpus(void)
-{
- void __iomem *scu_base = scu_base_addr();
- unsigned int i, ncores;
-
- if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9)
- ncores = scu_base ? scu_get_core_count(scu_base) : 1;
- else
- /*
- * CPU Nodes are passed thru DT and set_cpu_possible
- * is set by "arm_dt_init_cpu_maps".
- */
- return;
-
- /* sanity check */
- if (ncores > nr_cpu_ids) {
- pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
- ncores, nr_cpu_ids);
- ncores = nr_cpu_ids;
- }
-
- for (i = 0; i < ncores; i++)
- set_cpu_possible(i, true);
-}
-
static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
{
int i;
@@ -479,7 +449,6 @@
#endif /* CONFIG_HOTPLUG_CPU */
const struct smp_operations exynos_smp_ops __initconst = {
- .smp_init_cpus = exynos_smp_init_cpus,
.smp_prepare_cpus = exynos_smp_prepare_cpus,
.smp_secondary_init = exynos_secondary_init,
.smp_boot_secondary = exynos_boot_secondary,
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 4698940..093458b 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -7,7 +7,7 @@
# Common support
obj-y := id.o io.o control.o devices.o fb.o timer.o pm.o \
- common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o \
+ common.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o \
omap_device.o omap-headsmp.o sram.o drm.o
hwmod-common = omap_hwmod.o omap_hwmod_reset.o \
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 36d9943..dc9e34e 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -304,7 +304,7 @@
.init_late = am43xx_init_late,
.init_irq = omap_gic_of_init,
.init_machine = omap_generic_init,
- .init_time = omap4_local_timer_init,
+ .init_time = omap3_gptimer_timer_init,
.dt_compat = am43_boards_compat,
.restart = omap44xx_restart,
MACHINE_END
diff --git a/arch/arm/mach-omap2/gpio.c b/arch/arm/mach-omap2/gpio.c
deleted file mode 100644
index 7a57714..0000000
--- a/arch/arm/mach-omap2/gpio.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * OMAP2+ specific gpio initialization
- *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Author:
- * Charulatha V <charu@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/gpio.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/of.h>
-#include <linux/platform_data/gpio-omap.h>
-
-#include "soc.h"
-#include "omap_hwmod.h"
-#include "omap_device.h"
-#include "omap-pm.h"
-
-#include "powerdomain.h"
-
-static int __init omap2_gpio_dev_init(struct omap_hwmod *oh, void *unused)
-{
- struct platform_device *pdev;
- struct omap_gpio_platform_data *pdata;
- struct omap_gpio_dev_attr *dev_attr;
- char *name = "omap_gpio";
- int id;
- struct powerdomain *pwrdm;
-
- /*
- * extract the device id from name field available in the
- * hwmod database and use the same for constructing ids for
- * gpio devices.
- * CAUTION: Make sure the name in the hwmod database does
- * not change. If changed, make corresponding change here
- * or make use of static variable mechanism to handle this.
- */
- sscanf(oh->name, "gpio%d", &id);
-
- pdata = kzalloc(sizeof(struct omap_gpio_platform_data), GFP_KERNEL);
- if (!pdata) {
- pr_err("gpio%d: Memory allocation failed\n", id);
- return -ENOMEM;
- }
-
- dev_attr = (struct omap_gpio_dev_attr *)oh->dev_attr;
- pdata->bank_width = dev_attr->bank_width;
- pdata->dbck_flag = dev_attr->dbck_flag;
- pdata->get_context_loss_count = omap_pm_get_dev_context_loss_count;
- pdata->regs = kzalloc(sizeof(struct omap_gpio_reg_offs), GFP_KERNEL);
- if (!pdata->regs) {
- pr_err("gpio%d: Memory allocation failed\n", id);
- kfree(pdata);
- return -ENOMEM;
- }
-
- switch (oh->class->rev) {
- case 0:
- if (id == 1)
- /* non-wakeup GPIO pins for OMAP2 Bank1 */
- pdata->non_wakeup_gpios = 0xe203ffc0;
- else if (id == 2)
- /* non-wakeup GPIO pins for OMAP2 Bank2 */
- pdata->non_wakeup_gpios = 0x08700040;
- /* fall through */
-
- case 1:
- pdata->regs->revision = OMAP24XX_GPIO_REVISION;
- pdata->regs->direction = OMAP24XX_GPIO_OE;
- pdata->regs->datain = OMAP24XX_GPIO_DATAIN;
- pdata->regs->dataout = OMAP24XX_GPIO_DATAOUT;
- pdata->regs->set_dataout = OMAP24XX_GPIO_SETDATAOUT;
- pdata->regs->clr_dataout = OMAP24XX_GPIO_CLEARDATAOUT;
- pdata->regs->irqstatus = OMAP24XX_GPIO_IRQSTATUS1;
- pdata->regs->irqstatus2 = OMAP24XX_GPIO_IRQSTATUS2;
- pdata->regs->irqenable = OMAP24XX_GPIO_IRQENABLE1;
- pdata->regs->irqenable2 = OMAP24XX_GPIO_IRQENABLE2;
- pdata->regs->set_irqenable = OMAP24XX_GPIO_SETIRQENABLE1;
- pdata->regs->clr_irqenable = OMAP24XX_GPIO_CLEARIRQENABLE1;
- pdata->regs->debounce = OMAP24XX_GPIO_DEBOUNCE_VAL;
- pdata->regs->debounce_en = OMAP24XX_GPIO_DEBOUNCE_EN;
- pdata->regs->ctrl = OMAP24XX_GPIO_CTRL;
- pdata->regs->wkup_en = OMAP24XX_GPIO_WAKE_EN;
- pdata->regs->leveldetect0 = OMAP24XX_GPIO_LEVELDETECT0;
- pdata->regs->leveldetect1 = OMAP24XX_GPIO_LEVELDETECT1;
- pdata->regs->risingdetect = OMAP24XX_GPIO_RISINGDETECT;
- pdata->regs->fallingdetect = OMAP24XX_GPIO_FALLINGDETECT;
- break;
- case 2:
- pdata->regs->revision = OMAP4_GPIO_REVISION;
- pdata->regs->direction = OMAP4_GPIO_OE;
- pdata->regs->datain = OMAP4_GPIO_DATAIN;
- pdata->regs->dataout = OMAP4_GPIO_DATAOUT;
- pdata->regs->set_dataout = OMAP4_GPIO_SETDATAOUT;
- pdata->regs->clr_dataout = OMAP4_GPIO_CLEARDATAOUT;
- pdata->regs->irqstatus_raw0 = OMAP4_GPIO_IRQSTATUSRAW0;
- pdata->regs->irqstatus_raw1 = OMAP4_GPIO_IRQSTATUSRAW1;
- pdata->regs->irqstatus = OMAP4_GPIO_IRQSTATUS0;
- pdata->regs->irqstatus2 = OMAP4_GPIO_IRQSTATUS1;
- pdata->regs->irqenable = OMAP4_GPIO_IRQSTATUSSET0;
- pdata->regs->irqenable2 = OMAP4_GPIO_IRQSTATUSSET1;
- pdata->regs->set_irqenable = OMAP4_GPIO_IRQSTATUSSET0;
- pdata->regs->clr_irqenable = OMAP4_GPIO_IRQSTATUSCLR0;
- pdata->regs->debounce = OMAP4_GPIO_DEBOUNCINGTIME;
- pdata->regs->debounce_en = OMAP4_GPIO_DEBOUNCENABLE;
- pdata->regs->ctrl = OMAP4_GPIO_CTRL;
- pdata->regs->wkup_en = OMAP4_GPIO_IRQWAKEN0;
- pdata->regs->leveldetect0 = OMAP4_GPIO_LEVELDETECT0;
- pdata->regs->leveldetect1 = OMAP4_GPIO_LEVELDETECT1;
- pdata->regs->risingdetect = OMAP4_GPIO_RISINGDETECT;
- pdata->regs->fallingdetect = OMAP4_GPIO_FALLINGDETECT;
- break;
- default:
- WARN(1, "Invalid gpio bank_type\n");
- kfree(pdata->regs);
- kfree(pdata);
- return -EINVAL;
- }
-
- pwrdm = omap_hwmod_get_pwrdm(oh);
- pdata->loses_context = pwrdm_can_ever_lose_context(pwrdm);
-
- pdev = omap_device_build(name, id - 1, oh, pdata, sizeof(*pdata));
- kfree(pdata);
-
- if (IS_ERR(pdev)) {
- WARN(1, "Can't build omap_device for %s:%s.\n",
- name, oh->name);
- return PTR_ERR(pdev);
- }
-
- return 0;
-}
-
-/*
- * gpio_init needs to be done before
- * machine_init functions access gpio APIs.
- * Hence gpio_init is a omap_postcore_initcall.
- */
-static int __init omap2_gpio_init(void)
-{
- /* If dtb is there, the devices will be created dynamically */
- if (of_have_populated_dt())
- return -ENODEV;
-
- return omap_hwmod_for_each_by_class("gpio", omap2_gpio_dev_init, NULL);
-}
-omap_postcore_initcall(omap2_gpio_init);
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index 759e1d4..e8b9887 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -741,14 +741,14 @@
int ret = 0;
char name[MOD_CLK_MAX_NAME_LEN];
struct clk *clk;
+ static const char modck[] = "_mod_ck";
- /* +7 magic comes from '_mod_ck' suffix */
- if (strlen(oh->name) + 7 > MOD_CLK_MAX_NAME_LEN)
+ if (strlen(oh->name) >= MOD_CLK_MAX_NAME_LEN - strlen(modck))
pr_warn("%s: warning: cropping name for %s\n", __func__,
oh->name);
- strncpy(name, oh->name, MOD_CLK_MAX_NAME_LEN - 7);
- strcat(name, "_mod_ck");
+ strlcpy(name, oh->name, MOD_CLK_MAX_NAME_LEN - strlen(modck));
+ strlcat(name, modck, MOD_CLK_MAX_NAME_LEN);
clk = clk_get(NULL, name);
if (!IS_ERR(clk)) {
diff --git a/arch/arm/mach-omap2/omap_hwmod_common_data.h b/arch/arm/mach-omap2/omap_hwmod_common_data.h
index cdfbb44..f22e9cb 100644
--- a/arch/arm/mach-omap2/omap_hwmod_common_data.h
+++ b/arch/arm/mach-omap2/omap_hwmod_common_data.h
@@ -121,10 +121,6 @@
extern struct omap_hwmod_irq_info omap2_dispc_irqs[];
extern struct omap_hwmod_irq_info omap2_i2c1_mpu_irqs[];
extern struct omap_hwmod_irq_info omap2_i2c2_mpu_irqs[];
-extern struct omap_hwmod_irq_info omap2_gpio1_irqs[];
-extern struct omap_hwmod_irq_info omap2_gpio2_irqs[];
-extern struct omap_hwmod_irq_info omap2_gpio3_irqs[];
-extern struct omap_hwmod_irq_info omap2_gpio4_irqs[];
extern struct omap_hwmod_irq_info omap2_dma_system_irqs[];
extern struct omap_hwmod_irq_info omap2_mcspi1_mpu_irqs[];
extern struct omap_hwmod_irq_info omap2_mcspi2_mpu_irqs[];
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
index 5b2f513..2b138b6 100644
--- a/arch/arm/mach-omap2/prm_common.c
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -295,10 +295,8 @@
GFP_KERNEL);
if (!prcm_irq_chips || !prcm_irq_setup->saved_mask ||
- !prcm_irq_setup->priority_mask) {
- pr_err("PRCM: kzalloc failed\n");
+ !prcm_irq_setup->priority_mask)
goto err;
- }
memset(mask, 0, sizeof(mask));
diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index 56128da..07dd692 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -510,18 +510,19 @@
}
#endif /* CONFIG_ARCH_OMAP3 */
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX)
+#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX) || \
+ defined(CONFIG_SOC_AM43XX)
void __init omap3_gptimer_timer_init(void)
{
__omap_sync32k_timer_init(2, "timer_sys_ck", NULL,
1, "timer_sys_ck", "ti,timer-alwon", true);
-
- clocksource_probe();
+ if (of_have_populated_dt())
+ clocksource_probe();
}
#endif
#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) || \
- defined(CONFIG_SOC_DRA7XX) || defined(CONFIG_SOC_AM43XX)
+ defined(CONFIG_SOC_DRA7XX)
static void __init omap4_sync32k_timer_init(void)
{
__omap_sync32k_timer_init(1, "timer_32k_ck", "ti,timer-alwon",
diff --git a/arch/arm/mach-s3c24xx/common.c b/arch/arm/mach-s3c24xx/common.c
index f6c3f15..b59f4f4 100644
--- a/arch/arm/mach-s3c24xx/common.c
+++ b/arch/arm/mach-s3c24xx/common.c
@@ -345,10 +345,40 @@
[DMACH_USB_EP4] = { S3C24XX_DMA_APB, true, S3C24XX_DMA_CHANREQ(4, 3), },
};
+static const struct dma_slave_map s3c2410_dma_slave_map[] = {
+ { "s3c2410-sdi", "rx-tx", (void *)DMACH_SDI },
+ { "s3c2410-spi.0", "rx", (void *)DMACH_SPI0_RX },
+ { "s3c2410-spi.0", "tx", (void *)DMACH_SPI0_TX },
+ { "s3c2410-spi.1", "rx", (void *)DMACH_SPI1_RX },
+ { "s3c2410-spi.1", "tx", (void *)DMACH_SPI1_TX },
+ /*
+ * The DMA request source[1] (DMACH_UARTx_SRC2) are
+ * not used in the UART driver.
+ */
+ { "s3c2410-uart.0", "rx", (void *)DMACH_UART0 },
+ { "s3c2410-uart.0", "tx", (void *)DMACH_UART0 },
+ { "s3c2410-uart.1", "rx", (void *)DMACH_UART1 },
+ { "s3c2410-uart.1", "tx", (void *)DMACH_UART1 },
+ { "s3c2410-uart.2", "rx", (void *)DMACH_UART2 },
+ { "s3c2410-uart.2", "tx", (void *)DMACH_UART2 },
+ { "s3c24xx-iis", "rx", (void *)DMACH_I2S_IN },
+ { "s3c24xx-iis", "tx", (void *)DMACH_I2S_OUT },
+ { "s3c-hsudc", "rx0", (void *)DMACH_USB_EP1 },
+ { "s3c-hsudc", "tx0", (void *)DMACH_USB_EP1 },
+ { "s3c-hsudc", "rx1", (void *)DMACH_USB_EP2 },
+ { "s3c-hsudc", "tx1", (void *)DMACH_USB_EP2 },
+ { "s3c-hsudc", "rx2", (void *)DMACH_USB_EP3 },
+ { "s3c-hsudc", "tx2", (void *)DMACH_USB_EP3 },
+ { "s3c-hsudc", "rx3", (void *)DMACH_USB_EP4 },
+ { "s3c-hsudc", "tx3", (void *)DMACH_USB_EP4 }
+};
+
static struct s3c24xx_dma_platdata s3c2410_dma_platdata = {
.num_phy_channels = 4,
.channels = s3c2410_dma_channels,
.num_channels = DMACH_MAX,
+ .slave_map = s3c2410_dma_slave_map,
+ .slavecnt = ARRAY_SIZE(s3c2410_dma_slave_map),
};
struct platform_device s3c2410_device_dma = {
@@ -388,10 +418,36 @@
[DMACH_USB_EP4] = { S3C24XX_DMA_APB, true, 16 },
};
+static const struct dma_slave_map s3c2412_dma_slave_map[] = {
+ { "s3c2412-sdi", "rx-tx", (void *)DMACH_SDI },
+ { "s3c2412-spi.0", "rx", (void *)DMACH_SPI0_RX },
+ { "s3c2412-spi.0", "tx", (void *)DMACH_SPI0_TX },
+ { "s3c2412-spi.1", "rx", (void *)DMACH_SPI1_RX },
+ { "s3c2412-spi.1", "tx", (void *)DMACH_SPI1_TX },
+ { "s3c2440-uart.0", "rx", (void *)DMACH_UART0 },
+ { "s3c2440-uart.0", "tx", (void *)DMACH_UART0 },
+ { "s3c2440-uart.1", "rx", (void *)DMACH_UART1 },
+ { "s3c2440-uart.1", "tx", (void *)DMACH_UART1 },
+ { "s3c2440-uart.2", "rx", (void *)DMACH_UART2 },
+ { "s3c2440-uart.2", "tx", (void *)DMACH_UART2 },
+ { "s3c2412-iis", "rx", (void *)DMACH_I2S_IN },
+ { "s3c2412-iis", "tx", (void *)DMACH_I2S_OUT },
+ { "s3c-hsudc", "rx0", (void *)DMACH_USB_EP1 },
+ { "s3c-hsudc", "tx0", (void *)DMACH_USB_EP1 },
+ { "s3c-hsudc", "rx1", (void *)DMACH_USB_EP2 },
+ { "s3c-hsudc", "tx1", (void *)DMACH_USB_EP2 },
+ { "s3c-hsudc", "rx2", (void *)DMACH_USB_EP3 },
+ { "s3c-hsudc", "tx2", (void *)DMACH_USB_EP3 },
+ { "s3c-hsudc", "rx3", (void *)DMACH_USB_EP4 },
+ { "s3c-hsudc", "tx3", (void *)DMACH_USB_EP4 }
+};
+
static struct s3c24xx_dma_platdata s3c2412_dma_platdata = {
.num_phy_channels = 4,
.channels = s3c2412_dma_channels,
.num_channels = DMACH_MAX,
+ .slave_map = s3c2412_dma_slave_map,
+ .slavecnt = ARRAY_SIZE(s3c2412_dma_slave_map),
};
struct platform_device s3c2412_device_dma = {
@@ -534,10 +590,30 @@
[DMACH_MIC_IN] = { S3C24XX_DMA_APB, true, 29 },
};
+static const struct dma_slave_map s3c2443_dma_slave_map[] = {
+ { "s3c2440-sdi", "rx-tx", (void *)DMACH_SDI },
+ { "s3c2443-spi.0", "rx", (void *)DMACH_SPI0_RX },
+ { "s3c2443-spi.0", "tx", (void *)DMACH_SPI0_TX },
+ { "s3c2443-spi.1", "rx", (void *)DMACH_SPI1_RX },
+ { "s3c2443-spi.1", "tx", (void *)DMACH_SPI1_TX },
+ { "s3c2440-uart.0", "rx", (void *)DMACH_UART0 },
+ { "s3c2440-uart.0", "tx", (void *)DMACH_UART0 },
+ { "s3c2440-uart.1", "rx", (void *)DMACH_UART1 },
+ { "s3c2440-uart.1", "tx", (void *)DMACH_UART1 },
+ { "s3c2440-uart.2", "rx", (void *)DMACH_UART2 },
+ { "s3c2440-uart.2", "tx", (void *)DMACH_UART2 },
+ { "s3c2440-uart.3", "rx", (void *)DMACH_UART3 },
+ { "s3c2440-uart.3", "tx", (void *)DMACH_UART3 },
+ { "s3c24xx-iis", "rx", (void *)DMACH_I2S_IN },
+ { "s3c24xx-iis", "tx", (void *)DMACH_I2S_OUT },
+};
+
static struct s3c24xx_dma_platdata s3c2443_dma_platdata = {
.num_phy_channels = 6,
.channels = s3c2443_dma_channels,
.num_channels = DMACH_MAX,
+ .slave_map = s3c2443_dma_slave_map,
+ .slavecnt = ARRAY_SIZE(s3c2443_dma_slave_map),
};
struct platform_device s3c2443_device_dma = {
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
index fc033c0..eada0b5 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -356,5 +356,21 @@
status = "disabled";
};
};
+
+ vpu: vpu@d0100000 {
+ compatible = "amlogic,meson-gx-vpu";
+ reg = <0x0 0xd0100000 0x0 0x100000>,
+ <0x0 0xc883c000 0x0 0x1000>,
+ <0x0 0xc8838000 0x0 0x1000>;
+ reg-names = "vpu", "hhi", "dmc";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* CVBS VDAC output port */
+ cvbs_vdac_port: port@0 {
+ reg = <0>;
+ };
+ };
};
};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index 9696820..4cbd626 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -142,6 +142,16 @@
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
};
&uart_AO {
@@ -229,3 +239,9 @@
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 203be28..4a96e0f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -125,6 +125,16 @@
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
};
/* This UART is brought out to the DB9 connector */
@@ -234,3 +244,9 @@
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 51edd5b5..596240c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -506,3 +506,7 @@
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
+
+&vpu {
+ compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
index e99101a..cea4a3e 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
@@ -117,6 +117,16 @@
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
};
&uart_AO {
@@ -203,3 +213,9 @@
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index 9f89b99..6921624 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -43,7 +43,7 @@
#include "meson-gx.dtsi"
#include <dt-bindings/clock/gxbb-clkc.h>
-#include <dt-bindings/gpio/meson-gxbb-gpio.h>
+#include <dt-bindings/gpio/meson-gxl-gpio.h>
/ {
compatible = "amlogic,meson-gxl";
@@ -299,3 +299,7 @@
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
+
+&vpu {
+ compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index f859d75..5a337d3 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -90,6 +90,16 @@
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
};
/* This UART is brought out to the DB9 connector */
@@ -167,3 +177,9 @@
max-speed = <1000>;
};
};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
index c1974bb..eb2f0c3 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
@@ -112,3 +112,7 @@
};
};
};
+
+&vpu {
+ compatible = "amlogic,meson-gxm-vpu", "amlogic,meson-gx-vpu";
+};
diff --git a/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts b/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts
index a852e28..a83ed2c 100644
--- a/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts
+++ b/arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts
@@ -81,7 +81,7 @@
#address-cells = <0>;
interrupt-controller;
reg = <0x0 0x2c001000 0 0x1000>,
- <0x0 0x2c002000 0 0x1000>,
+ <0x0 0x2c002000 0 0x2000>,
<0x0 0x2c004000 0 0x2000>,
<0x0 0x2c006000 0 0x2000>;
interrupts = <1 9 0xf04>;
diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
index 64226d5..135890c 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
@@ -1367,7 +1367,7 @@
};
amba {
- compatible = "arm,amba-bus";
+ compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 9d1d7ad..29ed6b6 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -64,6 +64,16 @@
reg = <0x0 0x86000000 0x0 0x200000>;
no-map;
};
+
+ memory@85800000 {
+ reg = <0x0 0x85800000 0x0 0x800000>;
+ no-map;
+ };
+
+ memory@86200000 {
+ reg = <0x0 0x86200000 0x0 0x2600000>;
+ no-map;
+ };
};
cpus {
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index 6ffb051..dbea2c3 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -169,7 +169,7 @@
power-source = <3300>;
};
- sdhi0_pins_uhs: sd0 {
+ sdhi0_pins_uhs: sd0_uhs {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <1800>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts b/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts
index 3580896..ef1b9e5 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts
@@ -27,7 +27,7 @@
stdout-path = "serial0:115200n8";
};
- memory {
+ memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index 68a90833..54dc283 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -72,7 +72,7 @@
<1 10 0xf08>;
};
- amba_apu {
+ amba_apu: amba_apu@0 {
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
@@ -175,7 +175,7 @@
};
i2c0: i2c@ff020000 {
- compatible = "cdns,i2c-r1p10";
+ compatible = "cdns,i2c-r1p14", "cdns,i2c-r1p10";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 17 4>;
@@ -185,7 +185,7 @@
};
i2c1: i2c@ff030000 {
- compatible = "cdns,i2c-r1p10";
+ compatible = "cdns,i2c-r1p14", "cdns,i2c-r1p10";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 18 4>;
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 869dded..33b744d 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -331,6 +331,7 @@
CONFIG_DRM_PANEL_SIMPLE=m
CONFIG_DRM_I2C_ADV7511=m
CONFIG_DRM_HISI_KIRIN=m
+CONFIG_DRM_MESON=m
CONFIG_FB=y
CONFIG_FB_ARMCLCD=y
CONFIG_BACKLIGHT_GENERIC=m
diff --git a/drivers/firmware/arm_scpi.c b/drivers/firmware/arm_scpi.c
index 70e1323..9ad0b19 100644
--- a/drivers/firmware/arm_scpi.c
+++ b/drivers/firmware/arm_scpi.c
@@ -721,11 +721,17 @@
ret = scpi_send_message(CMD_SENSOR_VALUE, &id, sizeof(id),
&buf, sizeof(buf));
- if (!ret)
+ if (ret)
+ return ret;
+
+ if (scpi_info->is_legacy)
+ /* only 32-bits supported, hi_val can be junk */
+ *val = le32_to_cpu(buf.lo_val);
+ else
*val = (u64)le32_to_cpu(buf.hi_val) << 32 |
le32_to_cpu(buf.lo_val);
- return ret;
+ return 0;
}
static int scpi_device_get_power_state(u16 dev_id)
diff --git a/drivers/firmware/psci_checker.c b/drivers/firmware/psci_checker.c
index 44bdb78..29d58fe 100644
--- a/drivers/firmware/psci_checker.c
+++ b/drivers/firmware/psci_checker.c
@@ -270,8 +270,7 @@
struct cpuidle_device *dev;
struct cpuidle_driver *drv;
/* No need for an actual callback, we just want to wake up the CPU. */
- struct timer_list wakeup_timer =
- TIMER_INITIALIZER(dummy_callback, 0, 0);
+ struct timer_list wakeup_timer;
/* Wait for the main thread to give the start signal. */
wait_for_completion(&suspend_threads_started);
@@ -287,6 +286,7 @@
pr_info("CPU %d entering suspend cycles, states 1 through %d\n",
cpu, drv->state_count - 1);
+ setup_timer_on_stack(&wakeup_timer, dummy_callback, 0);
for (i = 0; i < NUM_SUSPEND_CYCLE; ++i) {
int index;
/*
diff --git a/include/dt-bindings/mfd/tps65217.h b/include/dt-bindings/mfd/tps65217.h
deleted file mode 100644
index cafb9e6..0000000
--- a/include/dt-bindings/mfd/tps65217.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * This header provides macros for TI TPS65217 DT bindings.
- *
- * Copyright (C) 2016 Texas Instruments
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program. If not, see <http://www.gnu.org/licenses/>.
- */
-
-#ifndef __DT_BINDINGS_TPS65217_H__
-#define __DT_BINDINGS_TPS65217_H__
-
-#define TPS65217_IRQ_USB 0
-#define TPS65217_IRQ_AC 1
-#define TPS65217_IRQ_PB 2
-
-#endif