ath5k: clean up some comments
This fixes a few misspellings, word repetitions, and some grammar
nits in ath5k comments. No code changes.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c
index f5434eb..4154959 100644
--- a/drivers/net/wireless/ath/ath5k/reset.c
+++ b/drivers/net/wireless/ath/ath5k/reset.c
@@ -959,7 +959,7 @@
AR5K_QUEUE_DCU_SEQNUM(0));
}
- /* TSF accelerates on AR5211 durring reset
+ /* TSF accelerates on AR5211 during reset
* As a workaround save it here and restore
* it later so that it's back in time after
* reset. This way it'll get re-synced on the
@@ -1080,7 +1080,7 @@
return ret;
/* Spur info is available only from EEPROM versions
- * bigger than 5.3 but but the EEPOM routines will use
+ * greater than 5.3, but the EEPROM routines will use
* static values for older versions */
if (ah->ah_mac_srev >= AR5K_SREV_AR5424)
ath5k_hw_set_spur_mitigation_filter(ah,
@@ -1173,11 +1173,11 @@
/* Set RSSI/BRSSI thresholds
*
* Note: If we decide to set this value
- * dynamicaly, have in mind that when AR5K_RSSI_THR
- * register is read it might return 0x40 if we haven't
- * wrote anything to it plus BMISS RSSI threshold is zeroed.
+ * dynamically, keep in mind that when AR5K_RSSI_THR
+ * register is read, it might return 0x40 if we haven't
+ * written anything to it. Also, BMISS RSSI threshold is zeroed.
* So doing a save/restore procedure here isn't the right
- * choice. Instead store it on ath5k_hw */
+ * choice. Instead, store it in ath5k_hw */
ath5k_hw_reg_write(ah, (AR5K_TUNE_RSSI_THRES |
AR5K_TUNE_BMISS_THRES <<
AR5K_RSSI_THR_BMISS_S),
@@ -1235,7 +1235,7 @@
/*
* Perform ADC test to see if baseband is ready
- * Set tx hold and check adc test register
+ * Set TX hold and check ADC test register
*/
phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
@@ -1254,15 +1254,15 @@
*
* This method is used to calibrate some static offsets
* used together with on-the fly I/Q calibration (the
- * one performed via ath5k_hw_phy_calibrate), that doesn't
+ * one performed via ath5k_hw_phy_calibrate), which doesn't
* interrupt rx path.
*
* While rx path is re-routed to the power detector we also
- * start a noise floor calibration, to measure the
+ * start a noise floor calibration to measure the
* card's noise floor (the noise we measure when we are not
- * transmiting or receiving anything).
+ * transmitting or receiving anything).
*
- * If we are in a noisy environment AGC calibration may time
+ * If we are in a noisy environment, AGC calibration may time
* out and/or noise floor calibration might timeout.
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,