Input: tsc2005 - add DT support
This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt
new file mode 100644
index 0000000..4b641c7
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt
@@ -0,0 +1,42 @@
+* Texas Instruments tsc2005 touchscreen controller
+
+Required properties:
+ - compatible : "ti,tsc2005"
+ - reg : SPI device address
+ - spi-max-frequency : Maximal SPI speed
+ - interrupts : IRQ specifier
+ - reset-gpios : GPIO specifier
+ - vio-supply : Regulator specifier
+
+Optional properties:
+ - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates
+ in ohm (defaults to 280)
+ - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after
+ the configured time (in milli seconds), the driver
+ will reset it. This is disabled by default.
+ - properties defined in touchscreen.txt
+
+Example:
+
+&mcspi1 {
+ tsc2005@0 {
+ compatible = "ti,tsc2005";
+ spi-max-frequency = <6000000>;
+ reg = <0>;
+
+ vio-supply = <&vio>;
+
+ reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
+ interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
+
+ touchscreen-fuzz-x = <4>;
+ touchscreen-fuzz-y = <7>;
+ touchscreen-fuzz-pressure = <2>;
+ touchscreen-max-x = <4096>;
+ touchscreen-max-y = <4096>;
+ touchscreen-max-pressure = <2048>;
+
+ ti,x-plate-ohms = <280>;
+ ti,esd-recovery-timeout-ms = <8000>;
+ };
+}
diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c
index d981e49..52380b6 100644
--- a/drivers/input/touchscreen/tsc2005.c
+++ b/drivers/input/touchscreen/tsc2005.c
@@ -25,11 +25,15 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/input.h>
+#include <linux/input/touchscreen.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/pm.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/tsc2005.h>
+#include <linux/regulator/consumer.h>
/*
* The touchscreen interface operates as follows:
@@ -100,6 +104,11 @@
TSC2005_CFR2_AVG_7)
#define MAX_12BIT 0xfff
+#define TSC2005_DEF_X_FUZZ 4
+#define TSC2005_DEF_Y_FUZZ 8
+#define TSC2005_DEF_P_FUZZ 2
+#define TSC2005_DEF_RESISTOR 280
+
#define TSC2005_SPI_MAX_SPEED_HZ 10000000
#define TSC2005_PENUP_TIME_MS 40
@@ -143,6 +152,9 @@
bool pen_down;
+ struct regulator *vio;
+
+ int reset_gpio;
void (*set_reset)(bool enable);
};
@@ -337,6 +349,14 @@
tsc2005_cmd(ts, TSC2005_CMD_STOP);
}
+static void tsc2005_set_reset(struct tsc2005 *ts, bool enable)
+{
+ if (ts->reset_gpio >= 0)
+ gpio_set_value(ts->reset_gpio, enable);
+ else if (ts->set_reset)
+ ts->set_reset(enable);
+}
+
/* must be called with ts->mutex held */
static void __tsc2005_disable(struct tsc2005 *ts)
{
@@ -355,7 +375,7 @@
{
tsc2005_start_scan(ts);
- if (ts->esd_timeout && ts->set_reset) {
+ if (ts->esd_timeout && (ts->set_reset || ts->reset_gpio)) {
ts->last_valid_interrupt = jiffies;
schedule_delayed_work(&ts->esd_work,
round_jiffies_relative(
@@ -414,9 +434,9 @@
}
/* hardware reset */
- ts->set_reset(false);
+ tsc2005_set_reset(ts, false);
usleep_range(100, 500); /* only 10us required */
- ts->set_reset(true);
+ tsc2005_set_reset(ts, true);
if (!success)
goto out;
@@ -459,7 +479,7 @@
umode_t mode = attr->mode;
if (attr == &dev_attr_selftest.attr) {
- if (!ts->set_reset)
+ if (!ts->set_reset && !ts->reset_gpio)
mode = 0;
}
@@ -509,9 +529,9 @@
tsc2005_update_pen_state(ts, 0, 0, 0);
- ts->set_reset(false);
+ tsc2005_set_reset(ts, false);
usleep_range(100, 500); /* only 10us required */
- ts->set_reset(true);
+ tsc2005_set_reset(ts, true);
enable_irq(ts->spi->irq);
tsc2005_start_scan(ts);
@@ -572,29 +592,47 @@
static int tsc2005_probe(struct spi_device *spi)
{
const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev);
+ struct device_node *np = spi->dev.of_node;
+
struct tsc2005 *ts;
struct input_dev *input_dev;
- unsigned int max_x, max_y, max_p;
- unsigned int fudge_x, fudge_y, fudge_p;
+ unsigned int max_x = MAX_12BIT;
+ unsigned int max_y = MAX_12BIT;
+ unsigned int max_p = MAX_12BIT;
+ unsigned int fudge_x = TSC2005_DEF_X_FUZZ;
+ unsigned int fudge_y = TSC2005_DEF_Y_FUZZ;
+ unsigned int fudge_p = TSC2005_DEF_P_FUZZ;
+ unsigned int x_plate_ohm = TSC2005_DEF_RESISTOR;
+ unsigned int esd_timeout;
int error;
- if (!pdata) {
+ if (!np && !pdata) {
dev_err(&spi->dev, "no platform data\n");
return -ENODEV;
}
- fudge_x = pdata->ts_x_fudge ? : 4;
- fudge_y = pdata->ts_y_fudge ? : 8;
- fudge_p = pdata->ts_pressure_fudge ? : 2;
- max_x = pdata->ts_x_max ? : MAX_12BIT;
- max_y = pdata->ts_y_max ? : MAX_12BIT;
- max_p = pdata->ts_pressure_max ? : MAX_12BIT;
-
if (spi->irq <= 0) {
dev_err(&spi->dev, "no irq\n");
return -ENODEV;
}
+ if (pdata) {
+ fudge_x = pdata->ts_x_fudge;
+ fudge_y = pdata->ts_y_fudge;
+ fudge_p = pdata->ts_pressure_fudge;
+ max_x = pdata->ts_x_max;
+ max_y = pdata->ts_y_max;
+ max_p = pdata->ts_pressure_max;
+ x_plate_ohm = pdata->ts_x_plate_ohm;
+ esd_timeout = pdata->esd_timeout_ms;
+ } else {
+ x_plate_ohm = TSC2005_DEF_RESISTOR;
+ of_property_read_u32(np, "ti,x-plate-ohms", &x_plate_ohm);
+ esd_timeout = 0;
+ of_property_read_u32(np, "ti,esd-recovery-timeout-ms",
+ &esd_timeout);
+ }
+
spi->mode = SPI_MODE_0;
spi->bits_per_word = 8;
if (!spi->max_speed_hz)
@@ -615,9 +653,37 @@
ts->spi = spi;
ts->idev = input_dev;
- ts->x_plate_ohm = pdata->ts_x_plate_ohm ? : 280;
- ts->esd_timeout = pdata->esd_timeout_ms;
- ts->set_reset = pdata->set_reset;
+ ts->x_plate_ohm = x_plate_ohm;
+ ts->esd_timeout = esd_timeout;
+
+ if (np) {
+ ts->reset_gpio = of_get_named_gpio(np, "reset-gpios", 0);
+ if (ts->reset_gpio == -EPROBE_DEFER)
+ return ts->reset_gpio;
+ if (ts->reset_gpio < 0) {
+ dev_err(&spi->dev, "error acquiring reset gpio: %d\n",
+ ts->reset_gpio);
+ return ts->reset_gpio;
+ }
+
+ error = devm_gpio_request_one(&spi->dev, ts->reset_gpio, 0,
+ "reset-gpios");
+ if (error) {
+ dev_err(&spi->dev, "error requesting reset gpio: %d\n",
+ error);
+ return error;
+ }
+
+ ts->vio = devm_regulator_get(&spi->dev, "vio");
+ if (IS_ERR(ts->vio)) {
+ error = PTR_ERR(ts->vio);
+ dev_err(&spi->dev, "vio regulator missing (%d)", error);
+ return error;
+ }
+ } else {
+ ts->reset_gpio = -1;
+ ts->set_reset = pdata->set_reset;
+ }
mutex_init(&ts->mutex);
@@ -642,6 +708,9 @@
input_set_abs_params(input_dev, ABS_Y, 0, max_y, fudge_y, 0);
input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0);
+ if (np)
+ touchscreen_parse_of_params(input_dev);
+
input_dev->open = tsc2005_open;
input_dev->close = tsc2005_close;
@@ -659,12 +728,19 @@
return error;
}
+ /* enable regulator for DT */
+ if (ts->vio) {
+ error = regulator_enable(ts->vio);
+ if (error)
+ return error;
+ }
+
spi_set_drvdata(spi, ts);
error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group);
if (error) {
dev_err(&spi->dev,
"Failed to create sysfs attributes, err: %d\n", error);
- return error;
+ goto disable_regulator;
}
error = input_register_device(ts->idev);
@@ -679,13 +755,21 @@
err_remove_sysfs:
sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
+disable_regulator:
+ if (ts->vio)
+ regulator_disable(ts->vio);
return error;
}
static int tsc2005_remove(struct spi_device *spi)
{
+ struct tsc2005 *ts = spi_get_drvdata(spi);
+
sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
+ if (ts->vio)
+ regulator_disable(ts->vio);
+
return 0;
}