[libata] use dev_printk() throughout drivers
A few drivers were not following the standard meme of printing out
their driver name and version at module load time; this is fixed
as well.
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index 5efb3c5..e2a5657 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -41,6 +41,7 @@
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/dma-mapping.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -674,10 +675,10 @@
if (!ahci_host_intr(ap, qc))
if (ata_ratelimit()) {
struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- printk(KERN_WARNING
- "ahci(%s): unhandled interrupt on port %u\n",
- pci_name(pdev), i);
+ to_pci_dev(ap->host_set->dev);
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "unhandled interrupt on port %u\n",
+ i);
}
VPRINTK("port %u\n", i);
@@ -685,10 +686,9 @@
VPRINTK("port %u (no irq)\n", i);
if (ata_ratelimit()) {
struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- printk(KERN_WARNING
- "ahci(%s): interrupt on disabled port %u\n",
- pci_name(pdev), i);
+ to_pci_dev(ap->host_set->dev);
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "interrupt on disabled port %u\n", i);
}
}
@@ -760,8 +760,8 @@
tmp = readl(mmio + HOST_CTL);
if (tmp & HOST_RESET) {
- printk(KERN_ERR DRV_NAME "(%s): controller reset failed (0x%x)\n",
- pci_name(pdev), tmp);
+ dev_printk(KERN_ERR, &pdev->dev,
+ "controller reset failed (0x%x)\n", tmp);
return -EIO;
}
@@ -789,22 +789,22 @@
if (rc) {
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 64-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "64-bit DMA enable failed\n");
return rc;
}
}
} else {
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 32-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit DMA enable failed\n");
return rc;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 32-bit consistent DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit consistent DMA enable failed\n");
return rc;
}
}
@@ -907,10 +907,10 @@
else
scc_s = "unknown";
- printk(KERN_INFO DRV_NAME "(%s) AHCI %02x%02x.%02x%02x "
+ dev_printk(KERN_INFO, &pdev->dev,
+ "AHCI %02x%02x.%02x%02x "
"%u slots %u ports %s Gbps 0x%x impl %s mode\n"
,
- pci_name(pdev),
(vers >> 24) & 0xff,
(vers >> 16) & 0xff,
@@ -923,11 +923,11 @@
impl,
scc_s);
- printk(KERN_INFO DRV_NAME "(%s) flags: "
+ dev_printk(KERN_INFO, &pdev->dev,
+ "flags: "
"%s%s%s%s%s%s"
"%s%s%s%s%s%s%s\n"
,
- pci_name(pdev),
cap & (1 << 31) ? "64bit " : "",
cap & (1 << 30) ? "ncq " : "",
@@ -960,7 +960,7 @@
VPRINTK("ENTER\n");
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)