wl12xx: implement set_bitrate_mask callback
Save the configured bitrate, and use the min allowed rate
as the basic rate (e.g. when scanning).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
diff --git a/drivers/net/wireless/wl12xx/cmd.c b/drivers/net/wireless/wl12xx/cmd.c
index 51be8f7..287fe95 100644
--- a/drivers/net/wireless/wl12xx/cmd.c
+++ b/drivers/net/wireless/wl12xx/cmd.c
@@ -1112,6 +1112,7 @@
{
struct sk_buff *skb;
int ret;
+ u32 rate;
skb = ieee80211_probereq_get(wl->hw, wl->vif, ssid, ssid_len,
ie, ie_len);
@@ -1122,14 +1123,13 @@
wl1271_dump(DEBUG_SCAN, "PROBE REQ: ", skb->data, skb->len);
+ rate = wl1271_tx_min_rate_get(wl, wl->bitrate_masks[band]);
if (band == IEEE80211_BAND_2GHZ)
ret = wl1271_cmd_template_set(wl, CMD_TEMPL_CFG_PROBE_REQ_2_4,
- skb->data, skb->len, 0,
- wl->conf.tx.basic_rate);
+ skb->data, skb->len, 0, rate);
else
ret = wl1271_cmd_template_set(wl, CMD_TEMPL_CFG_PROBE_REQ_5,
- skb->data, skb->len, 0,
- wl->conf.tx.basic_rate_5);
+ skb->data, skb->len, 0, rate);
out:
dev_kfree_skb(skb);
@@ -1140,6 +1140,7 @@
struct sk_buff *skb)
{
int ret;
+ u32 rate;
if (!skb)
skb = ieee80211_ap_probereq_get(wl->hw, wl->vif);
@@ -1148,14 +1149,13 @@
wl1271_dump(DEBUG_SCAN, "AP PROBE REQ: ", skb->data, skb->len);
+ rate = wl1271_tx_min_rate_get(wl, wl->bitrate_masks[wl->band]);
if (wl->band == IEEE80211_BAND_2GHZ)
ret = wl1271_cmd_template_set(wl, CMD_TEMPL_CFG_PROBE_REQ_2_4,
- skb->data, skb->len, 0,
- wl->conf.tx.basic_rate);
+ skb->data, skb->len, 0, rate);
else
ret = wl1271_cmd_template_set(wl, CMD_TEMPL_CFG_PROBE_REQ_5,
- skb->data, skb->len, 0,
- wl->conf.tx.basic_rate_5);
+ skb->data, skb->len, 0, rate);
if (ret < 0)
wl1271_error("Unable to set ap probe request template.");
@@ -1448,7 +1448,8 @@
sta_rates |= sta->ht_cap.mcs.rx_mask[0] << HW_HT_RATES_OFFSET;
cmd->supported_rates =
- cpu_to_le32(wl1271_tx_enabled_rates_get(wl, sta_rates));
+ cpu_to_le32(wl1271_tx_enabled_rates_get(wl, sta_rates,
+ wl->band));
wl1271_debug(DEBUG_CMD, "new peer rates=0x%x queues=0x%x",
cmd->supported_rates, sta->uapsd_queues);