bnx2x: Check for UNDI in uncommon branch
If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index cf14218..c506135 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -10053,6 +10053,24 @@
#define BCM_5710_UNDI_FW_MF_VERS (0x05)
#define BNX2X_PREV_UNDI_MF_PORT(p) (BAR_TSTRORM_INTMEM + 0x150c + ((p) << 4))
#define BNX2X_PREV_UNDI_MF_FUNC(f) (BAR_TSTRORM_INTMEM + 0x184c + ((f) << 4))
+
+static bool bnx2x_prev_is_after_undi(struct bnx2x *bp)
+{
+ /* UNDI marks its presence in DORQ -
+ * it initializes CID offset for normal bell to 0x7
+ */
+ if (!(REG_RD(bp, MISC_REG_RESET_REG_1) &
+ MISC_REGISTERS_RESET_REG_1_RST_DORQ))
+ return false;
+
+ if (REG_RD(bp, DORQ_REG_NORM_CID_OFST) == 0x7) {
+ BNX2X_DEV_INFO("UNDI previously loaded\n");
+ return true;
+ }
+
+ return false;
+}
+
static bool bnx2x_prev_unload_undi_fw_supports_mf(struct bnx2x *bp)
{
u8 major, minor, version;
@@ -10302,6 +10320,10 @@
BNX2X_DEV_INFO("Path is unmarked\n");
+ /* Cannot proceed with FLR if UNDI is loaded, since FW does not match */
+ if (bnx2x_prev_is_after_undi(bp))
+ goto out;
+
/* If function has FLR capabilities, and existing FW version matches
* the one required, then FLR will be sufficient to clean any residue
* left by previous driver
@@ -10322,6 +10344,7 @@
BNX2X_DEV_INFO("Could not FLR\n");
+out:
/* Close the MCP request, return failure*/
rc = bnx2x_prev_mcp_done(bp);
if (!rc)
@@ -10360,19 +10383,13 @@
/* close LLH filters towards the BRB */
bnx2x_set_rx_filter(&bp->link_params, 0);
- /* Check if the UNDI driver was previously loaded
- * UNDI driver initializes CID offset for normal bell to 0x7
- */
- if (reset_reg & MISC_REGISTERS_RESET_REG_1_RST_DORQ) {
- tmp_reg = REG_RD(bp, DORQ_REG_NORM_CID_OFST);
- if (tmp_reg == 0x7) {
- BNX2X_DEV_INFO("UNDI previously loaded\n");
- prev_undi = true;
- /* clear the UNDI indication */
- REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0);
- /* clear possible idle check errors */
- REG_RD(bp, NIG_REG_NIG_INT_STS_CLR_0);
- }
+ /* Check if the UNDI driver was previously loaded */
+ if (bnx2x_prev_is_after_undi(bp)) {
+ prev_undi = true;
+ /* clear the UNDI indication */
+ REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0);
+ /* clear possible idle check errors */
+ REG_RD(bp, NIG_REG_NIG_INT_STS_CLR_0);
}
if (!CHIP_IS_E1x(bp))
/* block FW from writing to host */