net: stmmac: add fix_mac_speed support for socfpga
This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
index ec632e6..cd613d7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
@@ -17,6 +17,7 @@
#include <linux/mfd/syscon.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/of_net.h>
#include <linux/phy.h>
#include <linux/regmap.h>
@@ -30,6 +31,12 @@
#define SYSMGR_EMACGRP_CTRL_PHYSEL_WIDTH 2
#define SYSMGR_EMACGRP_CTRL_PHYSEL_MASK 0x00000003
+#define EMAC_SPLITTER_CTRL_REG 0x0
+#define EMAC_SPLITTER_CTRL_SPEED_MASK 0x3
+#define EMAC_SPLITTER_CTRL_SPEED_10 0x2
+#define EMAC_SPLITTER_CTRL_SPEED_100 0x3
+#define EMAC_SPLITTER_CTRL_SPEED_1000 0x0
+
struct socfpga_dwmac {
int interface;
u32 reg_offset;
@@ -37,14 +44,46 @@
struct device *dev;
struct regmap *sys_mgr_base_addr;
struct reset_control *stmmac_rst;
+ void __iomem *splitter_base;
};
+static void socfpga_dwmac_fix_mac_speed(void *priv, unsigned int speed)
+{
+ struct socfpga_dwmac *dwmac = (struct socfpga_dwmac *)priv;
+ void __iomem *splitter_base = dwmac->splitter_base;
+ u32 val;
+
+ if (!splitter_base)
+ return;
+
+ val = readl(splitter_base + EMAC_SPLITTER_CTRL_REG);
+ val &= ~EMAC_SPLITTER_CTRL_SPEED_MASK;
+
+ switch (speed) {
+ case 1000:
+ val |= EMAC_SPLITTER_CTRL_SPEED_1000;
+ break;
+ case 100:
+ val |= EMAC_SPLITTER_CTRL_SPEED_100;
+ break;
+ case 10:
+ val |= EMAC_SPLITTER_CTRL_SPEED_10;
+ break;
+ default:
+ return;
+ }
+
+ writel(val, splitter_base + EMAC_SPLITTER_CTRL_REG);
+}
+
static int socfpga_dwmac_parse_data(struct socfpga_dwmac *dwmac, struct device *dev)
{
struct device_node *np = dev->of_node;
struct regmap *sys_mgr_base_addr;
u32 reg_offset, reg_shift;
int ret;
+ struct device_node *np_splitter;
+ struct resource res_splitter;
dwmac->stmmac_rst = devm_reset_control_get(dev,
STMMAC_RESOURCE_NAME);
@@ -73,6 +112,21 @@
return -EINVAL;
}
+ np_splitter = of_parse_phandle(np, "altr,emac-splitter", 0);
+ if (np_splitter) {
+ if (of_address_to_resource(np_splitter, 0, &res_splitter)) {
+ dev_info(dev, "Missing emac splitter address\n");
+ return -EINVAL;
+ }
+
+ dwmac->splitter_base = (void *)devm_ioremap_resource(dev,
+ &res_splitter);
+ if (!dwmac->splitter_base) {
+ dev_info(dev, "Failed to mapping emac splitter\n");
+ return -EINVAL;
+ }
+ }
+
dwmac->reg_offset = reg_offset;
dwmac->reg_shift = reg_shift;
dwmac->sys_mgr_base_addr = sys_mgr_base_addr;
@@ -91,6 +145,7 @@
switch (phymode) {
case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII;
break;
case PHY_INTERFACE_MODE_MII:
@@ -102,6 +157,13 @@
return -EINVAL;
}
+ /* Overwrite val to GMII if splitter core is enabled. The phymode here
+ * is the actual phy mode on phy hardware, but phy interface from
+ * EMAC core is GMII.
+ */
+ if (dwmac->splitter_base)
+ val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII;
+
regmap_read(sys_mgr_base_addr, reg_offset, &ctrl);
ctrl &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << reg_shift);
ctrl |= val << reg_shift;
@@ -196,4 +258,5 @@
.setup = socfpga_dwmac_probe,
.init = socfpga_dwmac_init,
.exit = socfpga_dwmac_exit,
+ .fix_mac_speed = socfpga_dwmac_fix_mac_speed,
};