gpio/mxc: Change gpio-mxc into an upstanding gpio driver
The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.
* Add a list to save all mx2 ports references, so that
mx2_gpio_irq_handler can walk through all interrupt status
registers
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxc_gpio_init into mxc_gpio_probe function
* Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
be public at all, and also make some other cleanup on
plat-mxc/include/mach/gpio.h at the same time
And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/arch/arm/mach-mx5/mm.c b/arch/arm/mach-mx5/mm.c
index ff55730..800bb8b2 100644
--- a/arch/arm/mach-mx5/mm.c
+++ b/arch/arm/mach-mx5/mm.c
@@ -69,8 +69,6 @@
mxc_arch_reset_init(MX53_IO_ADDRESS(MX53_WDOG1_BASE_ADDR));
}
-int imx51_register_gpios(void);
-
void __init mx51_init_irq(void)
{
unsigned long tzic_addr;
@@ -86,11 +84,8 @@
panic("unable to map TZIC interrupt controller\n");
tzic_init_irq(tzic_virt);
- imx51_register_gpios();
}
-int imx53_register_gpios(void);
-
void __init mx53_init_irq(void)
{
unsigned long tzic_addr;
@@ -103,5 +98,23 @@
panic("unable to map TZIC interrupt controller\n");
tzic_init_irq(tzic_virt);
- imx53_register_gpios();
+}
+
+void __init imx51_soc_init(void)
+{
+ mxc_register_gpio(0, MX51_GPIO1_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO1_LOW, MX51_MXC_INT_GPIO1_HIGH);
+ mxc_register_gpio(1, MX51_GPIO2_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO2_LOW, MX51_MXC_INT_GPIO2_HIGH);
+ mxc_register_gpio(2, MX51_GPIO3_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO3_LOW, MX51_MXC_INT_GPIO3_HIGH);
+ mxc_register_gpio(3, MX51_GPIO4_BASE_ADDR, SZ_16K, MX51_MXC_INT_GPIO4_LOW, MX51_MXC_INT_GPIO4_HIGH);
+}
+
+void __init imx53_soc_init(void)
+{
+ mxc_register_gpio(0, MX53_GPIO1_BASE_ADDR, SZ_16K, MX53_INT_GPIO1_LOW, MX53_INT_GPIO1_HIGH);
+ mxc_register_gpio(1, MX53_GPIO2_BASE_ADDR, SZ_16K, MX53_INT_GPIO2_LOW, MX53_INT_GPIO2_HIGH);
+ mxc_register_gpio(2, MX53_GPIO3_BASE_ADDR, SZ_16K, MX53_INT_GPIO3_LOW, MX53_INT_GPIO3_HIGH);
+ mxc_register_gpio(3, MX53_GPIO4_BASE_ADDR, SZ_16K, MX53_INT_GPIO4_LOW, MX53_INT_GPIO4_HIGH);
+ mxc_register_gpio(4, MX53_GPIO5_BASE_ADDR, SZ_16K, MX53_INT_GPIO5_LOW, MX53_INT_GPIO5_HIGH);
+ mxc_register_gpio(5, MX53_GPIO6_BASE_ADDR, SZ_16K, MX53_INT_GPIO6_LOW, MX53_INT_GPIO6_HIGH);
+ mxc_register_gpio(6, MX53_GPIO7_BASE_ADDR, SZ_16K, MX53_INT_GPIO7_LOW, MX53_INT_GPIO7_HIGH);
}