phylib: Add device reset GPIO support
The PHY devices sometimes do have their reset signal (maybe even power
supply?) tied to some GPIO and sometimes it also does happen that a boot
loader does not leave it deasserted. So far this issue has been attacked
from (as I believe) a wrong angle: by teaching the MAC driver to manipulate
the GPIO in question; that solution, when applied to the device trees, led
to adding the PHY reset GPIO properties to the MAC device node, with one
exception: Cadence MACB driver which could handle the "reset-gpios" prop
in a PHY device subnode. I believe that the correct approach is to teach
the 'phylib' to get the MDIO device reset GPIO from the device tree node
corresponding to this device -- which this patch is doing...
Note that I had to modify the AT803x PHY driver as it would stop working
otherwise -- it made use of the reset GPIO for its own purposes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Propagate actual errors from fwnode_get_named_gpiod()]
[geert: Avoid destroying initial setup]
[geert: Consolidate GPIO descriptor acquiring code]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index de7dd65..29da7a3 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -71,7 +71,6 @@ MODULE_LICENSE("GPL");
struct at803x_priv {
bool phy_reset:1;
- struct gpio_desc *gpiod_reset;
};
struct at803x_context {
@@ -254,22 +253,11 @@ static int at803x_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
struct at803x_priv *priv;
- struct gpio_desc *gpiod_reset;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
- if (phydev->drv->phy_id != ATH8030_PHY_ID)
- goto does_not_require_reset_workaround;
-
- gpiod_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
- if (IS_ERR(gpiod_reset))
- return PTR_ERR(gpiod_reset);
-
- priv->gpiod_reset = gpiod_reset;
-
-does_not_require_reset_workaround:
phydev->priv = priv;
return 0;
@@ -343,14 +331,14 @@ static void at803x_link_change_notify(struct phy_device *phydev)
* cannot recover from by software.
*/
if (phydev->state == PHY_NOLINK) {
- if (priv->gpiod_reset && !priv->phy_reset) {
+ if (phydev->mdio.reset && !priv->phy_reset) {
struct at803x_context context;
at803x_context_save(phydev, &context);
- gpiod_set_value(priv->gpiod_reset, 1);
+ phy_device_reset(phydev, 1);
msleep(1);
- gpiod_set_value(priv->gpiod_reset, 0);
+ phy_device_reset(phydev, 0);
msleep(1);
at803x_context_restore(phydev, &context);