ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index 0e7fed4..cb19dc1 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -1,5 +1,5 @@
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Bluegiga APX4 Development Kit";
@@ -40,13 +40,13 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */
- 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */
- 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_JTAG_RTCK__GPIO_4_20
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -56,10 +56,10 @@
lcdif_pins_apx4: lcdif-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -69,12 +69,12 @@
mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */
- 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */
- 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
- 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */
- 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */
+ MX28_PAD_SSP0_DATA4__SSP2_D0
+ MX28_PAD_SSP0_DATA5__SSP2_D3
+ MX28_PAD_SSP0_DATA6__SSP2_CMD
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ MX28_PAD_SSP2_SS1__SSP2_D1
+ MX28_PAD_SSP2_SS2__SSP2_D2
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -83,7 +83,7 @@
mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 {
fsl,pinmux-ids = <
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
fsl,drive-strength = <2>;
fsl,pull-up = <0>;