ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 5f9c0a0..023eaf7 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Freescale i.MX28 Evaluation Kit";
@@ -70,14 +70,14 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
- 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */
- 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */
- 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */
- 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -87,7 +87,7 @@
led_pin_gpio3_5: led_gpio3_5@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -97,8 +97,8 @@
gpmi_pins_evk: gpmi-nand-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -108,10 +108,10 @@
lcdif_pins_evk: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;